Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
5 results
Search Results
Item Технічне забезпечення гідропоніки, як прогресивного виду вирощування овочевих культур(ЦНТУ, 2022) Васильковська, К. В.; Ковальов, М. М.; Андрієнко, О. О.; Корнічева, Г. І.; Vasylkovska, К.; Kovalov, М.; Andriienko, О.; Kornicheva, Н.В статті запропоновано схему гідропонної установки (NFT) для вирощування зелених овочевих культур в умовах закритого ґрунту. Вирощування зелених овочевих культур в умовах гідропонних систем дає можливість отримувати врожай цілий рік, при чому в об’ємі набагато більшому ніж за ґрунтових умов. Розроблена конструкція гідропонної системи дає можливість отримувати сталий врожай рослин салату при використанні субстрату. Використана установка системи NFT із використанням поживного розчину мінерально-біологічних препаратів дозволяє отримати розсаду з добре розвиненою кореневою системою та надземною частиною. Проведені дослідження дали змогу отримати врожайність, що переважає врожайність в ґрунтових умовах на 10-15%, а в перерахунку на рік – в 5,0-5,5 рази. The aggravation of the food crisis and the impossibility of exporting agricultural products from the ports against the backdrop of the war in Ukraine only exacerbates the issue of food security. The purpose of writing the article is to substantiate the installation scheme for hydroponic cultivation of vegetable crops in closed soil conditions for obtaining stable harvests of vegetable crops throughout the year. To carry out research, a hydroponic plant that works on the principle of a nutrient layer (NFT) was developed and manufactured at the Department of General Agriculture of the Central Ukrainian National Technical University. The installation is designed for growing green vegetable crops. A coconut-agroperlite soil mixture was used as a substrate. The used installation is compact, provided with a lighting system and works in automatic mode. The useful area of the installation is 0.104 m2, so it is possible to grow from 40 to 112 lettuce plants at the same time. The use of a mineral solution in a hydroponic installation had a significant effect on the growth and development of lettuce plants and caused an increase in the area of leaf plates. In the experiment, the yield of Tudela variety lettuce was obtained - 4.9 kg/m2, which is 10-15% more than in soil conditions, and if the installation is used all year round - 5.0-5.5 times more. The advantage of the method is that there is no need to use fungicides. Since, without the presence of soil, there are no such pests as cabbageworm and sciaridis. And the biggest advantage is saving water and controlling the substances they absorb in the process of development. The latest systems of growing green vegetable crops in the conditions of hydroponic systems make it possible to harvest all year round, and in a much larger volume than under soil conditions. The developed design of the hydroponic system makes it possible to obtain a steady crop of lettuce plants when using a coconutagroperlite soil mixture as a substrate. The proposed installation of the NFT system using a nutrient solution of mineral-biological preparations made it possible to obtain seedlings with a well-developed root system and an above-ground part with a yield of 4.9 kg/m2.Item Теоретичне дослідження конусного стабілізатора потоку сипкого матеріалу установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2016) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryshaka, О.; Gutsul, V.; Artiuhov, А.Отримані залежності швидкості руху сипкого матеріалу по конусному стабілізатору залежно від величини кута конуса, відстані від конусного стабілізатора до заслінки клапана і коефіцієнта тертя сипкого матеріалу, зазору між торцем матеріалопровода і конусним стабілізатором, товщини шару сипкого матеріалу, що сходить з поверхні конуса. The resulting dependence of the speed of the free-flowing material in the feed device from the height of the free flight, the coefficient of friction, angle of inclination of the side walls of the receiving receiving hopper, as for the case of fixed position receiving hopper, and for the case of circular motion of the funnel for different values of the angular velocity. When you increase the angle of the surface of the cone to the horizontal and V0 the speed of descent of granular material from the cone increases, and the thickness of the layer of bulk material flow that is coming off the cone decreases. A significant impact on the speed of descent of granular material from the cone and the thickness of the layer of bulk material flow that is coming off the cone f has. For large values of the coefficient of friction of the granular material on the surface of the cone, the surface of the cone to cover the materials with small values of the coefficient of friction.Item Разработка установки для опреснения воды методом вымораживания(КНТУ, 2013) Барабаш, П. А.; Голубев, А. Б.; Трокоз, Я. Е.; Горин, В. В.; Барабаш, П. О.; Голубєв, О. Б.; Трокоз, Я. Е.; Горін, В. В.; Barabash, Petr; Golubev, Aleksey; Trokoz, Yaroslav; Gorin, YaroslavВ работе представлена установка, предназначенная для опреснения воды методом вымораживания с деформируемой льдогенерирующей поверхностью теплообмена. В роботі наведена установка, яка призначена для опріснення води методом виморожування з дерформуючою льдогенерирующею поверхнею теплообміну. This work presents a plant intended for desalination method of freezing with deformable ice generating heat exchange surface. Developed by installing УОВВ-100 is intended for desalination method of freezing with deformable льдогенерирующей surface heat transfer. Plant capacity - 100 l/h water with salt content 0,001...0,5 g/l (initial≈ 0.5 to 30 g/l). Installations are intended use in medical, food, meat and dairy industries. The main element of desalination plants such freezing type is ice (LH). The efficiency of the LH depends on the efficiency of operation of the plant for desalination method of freezing. Design LH takes into account technical innovations, a set of applications which gives a new technical and economic effect. Energy cost deformation льдообразующей surface significantly lower the energy cost cutting ice. Tests proved the capacity of the proposed design ice machine and allowed to determine the approximate value of the frequency of deformations (ω = 20 min-1) to obtain the maximum specific performance ice machine g= 260 kg/m2h.Item Експериментальні дослідження пневмомеханічного висівного апарата з периферійним розташуванням комірок для висіву насіння просапних культур(КНТУ, 2012) Васильковська, К. В.; Vasilkovskaya, K.Проведено експериментальні дослідження нового пневмомеханічного висівного апарата з периферійним розташуванням комірок для висіву насіння просапних культур. Результати досліджень свідчать про можливість підвищення ефективності точного висіву. Experimental researches of new pneumomechanical sowing vehicle are conducted with the peripheral location of barns for sowing of seed of the cultivated cultures. The results of researches testify to possibility of increase of efficiency of seed-spacing.Item Обгрунтування постачального пристрою установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2014) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryhsaka, O.; Gutsul, V.; Artiukhov, А.Визначений вплив параметрів постачального пристрою на швидкість руху сипкого матеріалу в каналах патрубків в стаціонарному положенні і при обертанні пристрою, зміна лінійної питомої маси сипкого матеріалу в патрубках, а також центр мас сипкого матеріалу. Установлено, що швидкість руху сипкого матеріалу в каналах патрубків при обертанні пристрою збільшується відносно його стаціонарного положення, що виключає порушення технологічного процесу із-за забивання каналів патрубків. Modern machines for loading friable materials into valve bags require a considerable amount of energy, allow the loss of fasoo material, as well as the violation of technological process at boot friable materials, so the improvement of modern mechanization is an actual scientific problem. The effect of the parameters of the feeding device the speed of movement of the friable material in the channels of the nozzle in a stationary position during rotation of the device, the change of a specific linear mass of granular material in the channel setup. It is established that the speed of the friable material in the channels of the nozzles during rotation of the device increases relative to its stationary position, which eliminates the violation of technological process of plugging nozzles. Resume: 1. The speed of movement of the friable material in patrols postchallenge of the device increases when the rotation of the rotor relative to the stationary position of the rotor. This makes it possible to avoid the accumulation of loose material that could lead to blockage of the channel. 2. With increasing angular velocity of rotation of the rotor the flow of material moves from the lower to the upper wall of the socket. 3. The weight of friable material in patrols, when the rotor is reduced.