Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.

У статі наводяться переваги збирання зернових культур методом обчісування на корені з подальшою доробкою обчісаного вороху на стаціонарному пункті в порівнянні з комбайновим збиранням. Збирання цією технологією виконується причіпною збиральною машиною, яка складається з обчісуючого пристрою, ходової частини, транспортуючої системи. Параметри пневмотранспортеру збиральної машини є недостатньо обґрунтовані, тому подальшому наводяться результати експериментальних досліджень технологічного процесу пневмотранспортеру для транспортування обчісаного вороху зернових у причіп – візок, а саме дальність польоту обчісаного вороху в залежності від частоти обертання валу відцентрового вентилятору, питомої подачі вихідного матеріалу та кута нахилу рухомої заслінки. The article presents the advantages of harvesting grain ears by the method of combing at the root use stripper harvesting module technology with subsequent processing in comparison with combining. Harvesting with this technology is performed by a trailed harvesting machine with stripper working bodies. The implementation of this technology is constrained by namely the lack of scientific substantiation of the operating modes of the pneumatic conveyor of the combed heap. In this regard, there is a problem of researching the pneumatic conveyor, for its solution a method of experimental research was developed, which will determine the optimal parameters and performance of the pneumatic conveyor combed heap.The results of experimental researches of technological process of the pneumotransporter for transportation of the combed heap of grain in the trailer - the cart, namely range of flight of the combed heap depending on frequency of rotation dampers. The parameters of the factors and the geometric dimensions of the experimental setup were determined by computer simulation in SolidWorks. During the simulation, a full-fledged computer model was developed in real size, where the parameters were obtained by changing the speed of the impeller and changing the geometry of the loading window and the pneumatic line. Using the results of theoretical research, modeling and analysis of literature sources, the limits of the values of the factors were determined, which are given in the table. To conduct experimental research, an experimental setup was made, which allowed to vary the values of variable factors, and thus obtain a variety of data on the range of the combed pile of wheat depending on the values of variable factors. It is established that it is most expedient to use a noncomposite three - level Box - Benkin plan for three factors, which makes it possible to obtain a mathematical model according to the conducted experiments. The mathematical model is obtained, which in the future will make it possible to establish rational parameters and modes of operation of the compressed heap pneumatic conveyor. Checking the significance of the coefficients. The significance of the regression coefficients indicated that all the coefficients are significant. Checking the adequacy of the model showed that the model is adequate.

У статті розглянуто побудову математичної моделі ймовірності проходження зернівки крізь шар обчісаного вороху зернових, а також проведено аналіз отриманої моделі. The article deals with the construction of a mathematical model for the probability of grain passing through a layer of combed heap of cereals, and an analysis of the model obtained. As a result of the modelling it has been revealed that: - in the case when the distance between the straws is bigger than the length of the grain and the diameter of the straw, the probability of sifting the grain is 0.875, under the condition that the distance between the straws is 10 mm; - if the distance between the straw is less than the sum of the diameter of the straw and the grain length, and at the same time more than the sum of the diameter of the straw and the width of the grains, then the probability of passing the grains through the straw is within the range of 0.85 ... 0.877 at the distance between straws of 6.0 ... 8, 05 mm; - if the distance between the straws is less than the sum of the straw diameter and the width of the grains, the probability of sifting both in the horizontal arrangement of the grains and in the vertical one is equal to zero. In order to provide the necessary conditions for the grains to pass through layers of straw there should be used the operating element that has the potential of mechanical impact on the bundle.

Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.

Browse

Filters

Settings

Sort By

Results per page

Search Results