Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
2 results
Search Results
Item Аналіз конструкцій індивідуальних доїльних установок на відповідність забезпечення вимог виробництва молока(КНТУ, 2013) Рубльов, В. І.; Дев’ятко, О. С.; Rublev, V.; Deviatko, E.Розглянуто основні вимоги до конструкцій індивідуальних доїльних установок згідно з міжнародними стандартами. Наведено блок схему транспортування молока від дійок вимені до збірної ємності. Вказано напрямок удосконалення технічного забезпечення покращення якості молока в умовах технологій доїння особистих селянських та фермерських господарствах. Розроблена і апробована конструкція удосконаленого устрію для індивідуальних доїльних установок. Considered set of requirements for individual construction milking according to international standards to ensure milk quality at the global level, which was based on the analysis of the standard ISO 5707:2007 and ISO 6690:2007. It is possible by using a systematic approach to consider the individual components of the milking machines and create a flowchart. On the basis of which it was found that transport milk is in the system milking machine. It was therefore examined the interaction of the components of the reduced system of individual milking machines and their impact on the quality of milk. This analysis allowed to be determined with the the least protected stage in the line of transporting, and by direction of improvement of the technical providing and improvement of quality of milk in the conditions of technologies of milking the personal peasant and farmer economies. Based on patent information retrieval have been confirmed are listed priority areas of work and design. Improvements are taken to the improvement of receipt of quality of milk at his transporting in accordance with world requirements. A maintainance of the maximally close bacterial state of milk is on an output from a cattle. Designed and tested device of improved design for individual milking machines.Item Обгрунтування постачального пристрою установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2014) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryhsaka, O.; Gutsul, V.; Artiukhov, А.Визначений вплив параметрів постачального пристрою на швидкість руху сипкого матеріалу в каналах патрубків в стаціонарному положенні і при обертанні пристрою, зміна лінійної питомої маси сипкого матеріалу в патрубках, а також центр мас сипкого матеріалу. Установлено, що швидкість руху сипкого матеріалу в каналах патрубків при обертанні пристрою збільшується відносно його стаціонарного положення, що виключає порушення технологічного процесу із-за забивання каналів патрубків. Modern machines for loading friable materials into valve bags require a considerable amount of energy, allow the loss of fasoo material, as well as the violation of technological process at boot friable materials, so the improvement of modern mechanization is an actual scientific problem. The effect of the parameters of the feeding device the speed of movement of the friable material in the channels of the nozzle in a stationary position during rotation of the device, the change of a specific linear mass of granular material in the channel setup. It is established that the speed of the friable material in the channels of the nozzles during rotation of the device increases relative to its stationary position, which eliminates the violation of technological process of plugging nozzles. Resume: 1. The speed of movement of the friable material in patrols postchallenge of the device increases when the rotation of the rotor relative to the stationary position of the rotor. This makes it possible to avoid the accumulation of loose material that could lead to blockage of the channel. 2. With increasing angular velocity of rotation of the rotor the flow of material moves from the lower to the upper wall of the socket. 3. The weight of friable material in patrols, when the rotor is reduced.