Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
4 results
Search Results
Item Розмірна та параметрична градація верстата з МПС(КНТУ, 2016) Вахніченко, Д. В.; Верхогляд, Ю. І.; Брайко, М. В.В статті виконано дослідження розмірів і параметрів верстатів з механізмом паралельної структури та їх градація. Розглянуто відповідність між технічними характеристиками верстата і величиною необхідних координатних рухів виконавчого органа та умови досягнення узгодженості між цими характеристиками та вимогами, що ставляться до виконання операцій. Наведено модульну будову конструкцій верстата з МПС та запропоновано визначення основних параметрів кожного модуля та їх градацію на основі стандарту. В роботі запропоновано поділ верстатів з механізмами паралельної структури по максимальним координатним рухам, опираючись на переважні ряди чисел, основний та додатковий. Запропоновано градація верстатів за величиною кута обертання ланок в опорах платформ та по максимальному куту, під яким можлива обробка. Також представлено регламентовані параметри для лінійних розмірів, діаметрів рухомої та нерухомої платформ, відстані між їх опорами, розміру виконавчого органа та габаритних розміри несучої системи верстата. The paper used to study the size and parameters of machines with the mechanism of parallel structure and grading. We consider the correspondence between the technical characteristics of the machine and the size of the necessary co-ordinate the movements of the executive body and achieving coherence between these characteristics and the requirements of the procedures. Powered by a modular structure of the machine design with the MPS and the suggested definition of the basic parameters of each module and their graduation on the basis of the standard. The paper suggested the division of machines with parallel structure mechanisms with the maximum coordinate movements. And it is determined that most of them are the same as the next primary R20 numbers with ratio of 1.12. For these and other conditions, it is advisable to have an extra row with finer gradations, which, in accordance with GOST R40 must meet a number with a denominator 1,06. Tak for further recommendations when selecting certain parameters, preference should be given to the main or first additional row. Achieved a justification of key design parameters of MPS machines can be used as the basis of the standard. As a result, it is proposed grading machines largest units in the rotation angle of platforms and supports the maximum angle at which can be processed. Also presented regulated parameters of the linear sizes, diameters mobile and fixed platforms, the distance between their legs, the size of the executive body and the overall dimensions of the machine carrier system.Item Підвищення геометричної точності гексапода(КНТУ, 2013) Кириченко, А. М.На основі кінематичних залежностей визначено вплив відхилень положення центрів шарнірних опор на точність положення робочого органа верстата. Запропоновано метод обчислення положень центрів шарнірних опор за результатами обміру еталонної деталі вимірювальним контактним датчиком. The purpose of article is increasing the geometric accuracy of hexapod parallel manipulator by identifying the joint center positions. Using hexapod kinematics the influence of joint center position errors upon accuracy of the platform position and orientation is determined. A method is suggested to calculate the joint center positions from results of measurement of reference part with a touch probe. The reference part can be a cylinder, a sphere or a cube. The identification was simulated with random errors introduced to joints center positions, also considering the reference part geometry errors and measurement errors. The method was implemented for CNC hexapod machine tool, where a cylinder shaped reference part was measured with a touch probe mounted in the spindle. According to the results of numerical simulation and experimental easurements, the method can improve the geometric accuracy of hexapod up to 3-5 times.Item Дослідження впливу компонувальної схеми та діапазону зміни довжини кінематичних ланок на просторові рухові характеристики гексаподів(КНТУ, 2015) Валявський, І. А.; Кулєшков, Ю. В.; Valyavsky, Ivan; Kuleshkov, YuriyВ статті розглянуто вплив конструктивних параметрів (компонувальної схеми та діапазону зміни довжини кінематичних ланок) на розміри та об‘єм робочого простору верстата-гексапода. Use parallel kinematics machine tools is one of problems solving expanding functional capabilities of machine tools. Hexapod is one of that machine tools. Determining the most efficient design parameters of the hexapod main elements is an urgent problem. The results of previous theoretical research determined that the design of hexapod and length of struts and their movements influence the geometric characteristics hexapod workspace. Modeling workspace for different layouts of hexapod and obtained graphic dependences between workspace parameters and lengths of kinematic links. The article considers the influence of the design parameters (lyout of the machine and changing the length of the range of struts) on the shape, size and volume of the working space of the hexapod machine-tool and determine the most efficient execution heksapodiv options depending on their functionality.Item Зона обслуговування верстата з МПС при виконанні свердлильних операцій(КНТУ, 2014) Павленко, І. І.; Вахніченко, Д. В.; Якименко, С. М.; Pavlenko, І.; Vakhnichenko, D.; Yakimenko, S.В статті визначається зона обслуговування робочого простору верстату з МПС при свердлінні деталі, в якій отвори розташовані з різних боків. Operation of the machine is possible with the geometric space that is a working space of the machine with a parallel structure of the mechanism. Reasoned determination of the magnitude of this space allows him to set reasonable sizes depending on the mechanism used with parallel structure. The article is made a general equation for determining the coverage area of the working space of the machine with the mechanism of parallel structure when performing drilling operations at an angle. As a result, to analyze the influence of design parameters of the mechanism of parallel structure to the service area.