Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
3 results
Search Results
Item Технологічні особливості виготовлення дискових робочих органів ґрунтообробних та посівних машин(ЦНТУ, 2020) Кропівний, В. М.; Свірень, М. О.; Кузик, О. В.; Амосов, В. В.; Козловський, М. А.; Kropivny, V.; Sviren, M.; Kuzyk, O.; Amosov, V.; Kozlovsky, M.; Кропивный, В. Н.; Свирень, Н. А.; Кузык, А. В.; Козловский, Н. А.Провідні світові виробники досягають високих показників зносостійкості та міцності дисків з борвмісних сталей як їх хімічним складом, так і вибором раціональної технології термічної обробки. Експериментальні дослідження зразків деталей зі сталі марки 30MnB5 дозволили визначити, що для досягнення максимальних значень твердості достатньо нагріву протягом 15 хвилин до температури 850º С та гартування у воді. Щоб запобігти зниженню твердості та забезпечити необхідну пружність та в’язкість дисків, рекомендується відпускання при температурі 180º С. Розроблено технологічний процес та виробничу дільницю виготовлення сферичних дисків. The purpose of this study is to improve the technology of manufacturing spherical disk working bodies of tillage machines to increase their wear resistance and strength. The world's leading manufacturers achieve high wear resistance and strength of discs made of boron-containing steels both in their chemical composition and the choice of rational heat treatment technology. Experimental studies of 30MnB5 steel parts revealed that heating for 15 minutes to a temperature of 850°C and quenching in water was sufficient to achieve maximum hardness values. To prevent hardness reduction and to ensure the necessary elasticity and viscosity of the discs, it is recommended to temper at a temperature of 180°C and combine with heat before painting with powder paint. The application of cutting blanks with cutting of depressions along the outer contour of the disk and internal holes on the laser machine, as well as the formation of the finished shape of parts in the process of hot stamping and subsequent heat treatment in quenching dies. 1. The market of disk working bodies of tillage and sowing machines is studied, technological processes of manufacturing of which it is expedient to improve. 2. Theoretical and experimental study of the structure, structure and material properties of samples of spherical disks of imported agricultural machinery. The choice of 30MnB5 pine steel for their production is substantiated. 3. The improved technological process of manufacturing spherical disks is developed. It is recommended to form them by hot stamping in cold dies and intensive hardening in a water bath. 4. The project development of the section of production of disk working bodies of tillage and sowing equipment is carried out. Ведущие мировые производители достигают высоких показателей износоустойчивости и прочности дисков из борсодержащих сталей как их химическим составом, так и выбором рациональной технологии термической обработки. Экспериментальные исследования образцов деталей из стали марки 30MnB5 позволили определить, что для достижения максимальных значений твердости достаточно нагрева на протяжении 15 минут до температуры 850º С и закалки в воде. Чтобы предотвратить снижение твердости и обеспечить необходимую упругость и вязкость дисков, рекомендуется отпуск при температуре 180º С. Разработан технологический процесс и производственный участок изготовления сферических дисков.Item До розрахунку міцності різьбових з’єднань(КНТУ, 2016) Невдаха, А. Ю.; Дубовик, В. О.; Nevdaha, А.; Dubovik, V.В статті проведені дослідження метричних різьбових з’єднань, які дозволяють розраховувати коефіцієнт повноти різьби. Це дає можливість збільшити міцність різьбових з’єднань і, як результат, підвищити надійність вузла і машини в цілому. В розрахунках враховували, що сила розподілена по поверхні витка і прикладена в центрі ваги його робочої поверхні. При цьому враховували зусилля, яке руйнує тіло болта, а також силу зрізу різьби болта і зусилля зрізу витка гайки. З отриманих рівнянь зрізу для витків болта і гайки визначили коефіцієнт повноти різьби. В результаті проведених досліджень були отримані умови рівноміцності стержня болта і різьби гайки. Із співвідношень для метричних стандартних різьб і однакових матеріалів болта та гайки визначили висоту гайки, яка відповідає висоті стандартних гайок. The paper studies metric threaded connections which allow to calculate the coefficient of completeness thread. This makes it possible to increase the strength of threaded connections and as a result increase the reliability of the site and the car in general. The calculations take into account that the force is distributed over the surface of the coil and attached to the center of gravity of its working surface. This took into account the efforts that destroys the body bolt and screw thread cut power and effort slice spiral nuts. From these equations for cut turns the bolt and nut factor determined completeness thread. As a result of the research were obtained conditions rivnomitsnosti rod bolt and nut thread. With relations for metric standard thread and the same material bolt nuts and nut height determined which corresponds to the height standard screws.Item Міцнісні властивості компонентів для дражирування насіння(КНТУ, 2014) Сербій, Є. К.; Serbiy, Е.В статті обґрунтовано доцільність та наведено методику експериментальних досліджень з визначення міцнісних властивостей компонентів для дражирування насіння, встановлено залежності модуля Юнга та максимальної відносної деформації зразків з суміші бентоніту та гумату від її кількісного складу та абсолютної вологості, перевірено їх адекватність. The expediency and the experimental research methodology for strength properties determination of components for seeds pelleting, the dependences of the Young modulus and the maximum relative deformation of samples from a mixture of bentonite and humate on its composition and absolute humidity, checked their adequacy are informed in the article. It is established that pelleted seeds rationally be made from several layers: the outer, it is advisable to form out of 100% bentonite, because it has the maximum strength of 6.0•108 ... of 6.5•108 Pa at a moisture content close to your natural and significantly reduces the strength of 2.5•108 ... of 3.0•108 Pa at the increase of soil moisture. The dependences of the elastic modulus and the maximum relative elastic deformation of the mixture of bentonite and humate from humidity and quantitative composition is useful for discrete dynamic modeling pelleted seed.