Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
4 results
Search Results
Item Експериментальні дослідження ефективності функціонування систем забезпечення мікроклімату від’ємного тиску в тваринницьких приміщеннях(ЦНТУ, 2023) Калетнік, Г. М.; Яропуд, В. М.; Kaletnik, Н.; Yaropud, V.Обґрунтування раціональної схеми системи забезпечення мікроклімату від’ємного тиску в тваринницьких приміщеннях на основі виробничих обстежень є основною метою проведених досліджень. За результатами досліджень встановлено, що для тваринницького приміщення із системою вентиляції наземного каналу забезпечується більше свіжого повітря в зоні перебування тварин, у порівняні зі стельовою системою вентиляції і системою вентиляції через стінові канали. The microclimate of livestock premises is determined by a set of physical, chemical and biological parameters inside the premises for keeping animals and is characterized by the following parameters: air temperature, internal surfaces of walls, ceilings, floors, windows, doors, and other internal structures; humidity of air, internal surfaces of walls, ceiling, floor, windows, doors, and other internal structures; the speed and direction of air flows in the locations of animals, manure, inflow and exhaust channels, windows and doors; the gas composition of the air - the concentration of carbon dioxide, ammonia, hydrogen sulfide, carbon monoxide; the presence of dust and microorganisms in the air; the intensity of natural and artificial lighting; optical radiation; the level of industrial noise, the degree of air ionization. The substantiation of the rational scheme of the negative pressure microclimate system in livestock premises on the basis of production surveys is the main goal of the conducted research. According to the results of the research, it was found that for the livestock room with the ventilation system of the ground channel, more fresh air is provided in the area where the animals are staying, in comparison with the ceiling ventilation system and the ventilation system through the wall channels. For the ground duct ventilation system and the wall duct ventilation system, the efficiency of contaminant removal was influenced by the ventilation rate, which is significantly dependent on the animal's age, weight, and outdoor temperature. For the ventilation system of the above-ground channel in production conditions, the efficiency of pollution removal decreased with an increase in the speed of the air flow in the ventilation. For the wall duct ventilation system, the efficiency of pollutant removal increased as the ventilation air flow rate increased, as the sampling point was located at the back of the room. In a room with a ceiling ventilation system, the efficiency of contaminant removal was significantly influenced by the lying behavior of animals, and a slight decrease in the efficiency of contaminant removal was observed with increasing ventilation.Item Результати експериментальних досліджень біотермічних процесів компостування підстилкового посліду на основі лушпиння соняшнику в натурних буртах(ЦНТУ, 2017) Павленко, С. І.; Павленко, С. И.; Pavlenko, S.Втрати поживних біогенних речовин підстилкового посліду пов’язані з фізико-хімічними і мікробіологічними процесами, які відбуваються безпосередньо після виділення екскрементів тваринами, а також під час накопичення, зберігання і перероблення. Під впливом механізованих втручань та біоконверсних перетворень відбуваються зміни в масовому балансі біогенних компонентів тваринницьких відходів та в біоенергетичному потенціалі. Мета – дослідження технологічних процесів прискореного біотермічного компостування підстилкового посліду на основі лушпиння соняшнику технічними засобами механізованого компостування. Методи і прийоми досліджень: метод натурних спостережень, методи планування експерименту, методики тепловізерних і пірометричних спостережень, електротехнічні прийоми визначення динаміки зміни температури. Динаміка температур у буртах досліджувалася з використанням персонального комп’ютера до якого підключався електронний термометр TM-32/H-5T із системою температурних зондів на основі датчиків температури DS18B20. Температурне поле поверхні або розрізу буртів визначалося з використанням тепловізора Testo-875, який дозволяє проводити аналіз температурних полів із абсолютною похибкою вимірювання 0,01 °С. В результаті дослідження отримана динаміка зміни температури в кожній точці натурного бурта згідно розробленої методики. Потери питательных биогенных веществ подстилочного помета связанные с физико-химическим и микробиологическим процессами, которые происходят непосредственно после выделения экскрементов животных, а также во время накопления, хранения и переработки. Под влиянием механизированных вмешательств и биоконверсных преобразований происходят изменения в массовом балансе биогенных компонентов животноводческих отходов и в биоэнергетическом потенциале. Цель - исследование технологических процессов ускоренного биотермического компостирования подстилочного помета на основе шелухи подсолнечника техническими средствами механизированного компостирования. Методы и приемы исследований: метод натурных наблюдений, методы планирования эксперимента, методики тепловизерних и пирометрических наблюдений, электротехнические приемы определения динамики изменения температуры. Динамика температур в буртах исследовалась с использованием персонального компьютера к которому подключался электронный термометр TM-32 / H-5T с системой температурных зондов на основе датчиков температуры DS18B20. Температурное поле поверхности или разреза буртов определялось с использованием тепловизора Testo-875, который позволяет проводить анализ температурных полей с абсолютной погрешностью измерения 0,01 ° С. В результате исследования получена динамика изменения температуры в каждой точке натурного бурта согласно разработанной методики. Loss of nutrient nutrients of litter litter is associated with physico-chemical and microbiological processes that occur immediately after the excrement of animals, as well as during accumulation, storage and processing. Under the influence of mechanized interventions and bioconversal transformations, changes in the mass balance of nutrient components of livestock wastes and in bioenergy potential are taking place. The purpose is to study the technological processes of accelerated biodegradation composting of litter litter based on sunflower husk by technical means of mechanized composting. Methods and techniques of research: method of field observations, methods of planning the experiment, methods of thermal and pyrometric observations, electrotechnical methods of determining the dynamics of temperature change. The temperature dynamics in the booths was studied using a personal computer to which an electronic thermometer TM-32 / H-5T with a temperature sensor system based on DS18B20 temperature sensors was connected. The temperature field of the surface or the cut of burs was determined using the thermo-testor Testo-875, which allows the analysis of temperature fields with an absolute measurement error of 0.01 ° C. As a result of the study, the dynamics of temperature variation at each point of the bourse according to the developed method is obtained. The results of researches showed that mechanical abrasion of raw materials - aeration, provides growth of internal temperatures - 7 points of measurement on the height of the port H1 = 1.5 m to a maximum temperature of 65-71 ° C and up to 50-58 ° C at the height of the port H2 = 1, 0 m for 2-3 days after packing of the bouquet. At 15-17 days, the temperature drops to 50 ° C, which does not correspond to the thermophilic mode of bacterial activity, and the processes go to the mesophilic regime - up to 40 ° C. Humidification - up to 20% of the mass of the broom and aeration - effective technological techniques that provide temperature maintenance of the corresponding thermophilic regime 3-5 days more without using them.Item Дослідження мінімаксного керування та спостереження теплових об’єктів сільськогосподарського призначення(КНТУ, 2013) Лобок, О. П.; Гончаренко, Б. М.; Слєзенко, А. М.; Lobok, O.; Goncharenko, B.; Slyezenko, A.Наводяться розв’язки задач мінімаксного керування та спостереження багатовимірного теплового об’єкта керування (напр. сушарна камера) за умов повних і точних, а також неповних і неточних вимірювань параметрів стану. Експериментально досліджені оптимальні керування, спостереження, стан координат та значення критеріїв оптимальності об’єкта за цих умов. Досліджені припустимі збурення для випадку неповних і неточних вимірювань, обчислені значення критеріїв і значення їхніх верхніх меж. Здійснений аналіз перехідних процесів (ПП) елементів матриць зворотного зв’язку для обох випадків вимірювань стану об’єкта. Здійснений аналіз ПП оптимальних керувань, станів системи, спостережень і оптимальних оцінок якості роботи мінімаксного фільтра Калмана-Бюсі. Досліджена оптимальна область припустимих збурень. Доведено, що синтезоване мінімаксне керування має запас стійкості більший від розрахованого. The solutions to the minimax control and monitor thermal dimensional object сontrol (e.g. drying chamber) in a comprehensive and accurate, as well as incomplete and inaccurate measurements of the state. Experimentally studied the optimal control, monitoring, and the values of the state of origin of the optimality criteria of the object in these conditions. Investigated admissible perturbations in the case of incomplete and inaccurate measurements, calculating the values of the criteria and the value of their upper limits. The analysis of transients matrix elements of feedback for both cases, the measurement object's state. The analysis of the transients optimal controls, system states, observations and assessments of the quality of the optimal minimax Kalman-Bucy filter. The optimal range of admissible perturbations. It is proved that the synthesized minimax control has a margin of stability, the larger of the calculated.Item Вплив властивостей компонентів КМ (КП) на напружено-деформований стан і триботехнічні характеристики деталей СГТ(КНТУ, 2015) Аулін, В. В.; Кузик, О. В.; Носуленко, В. І.; Aulin, Viktor; Kuzyk, Oleksandr; Nosulenko, VictorРозглянуто різновиди контактування трибоелементів (ТЕ), зміцнених КМ (КП), які дозволяють істотно змінювати якість фізичного контакту, величину фактичної площі, здатність поверхневого шару (ПШ) ТЕ до еволюції складу і структури в процесі тертя та зношування. Виявлено ефективне гальмування руху дислокацій гетерогенними структурами КМ (КП), як при низьких, так і при високих температурах, а також рекристалізаційні процеси. Розглянуто напружений стан матеріалу ТЕ з КМ (КП) при терті. Отримано умову пластичної рівноваги компонентів у вигляді системи рівнянь та формула величини напруження при переході від матеріалу наповнювача до матеріалу матриці та визначено характер деформації, яким вони підлягають. Отримано вираз для критичного кута нахилу виступу і коефіцієнта тертя та проведена оцінка зміни коефіцієнта тертя. В процесі тертя і зношування ПШ КМ (КП) підлягає пружно-пластичному деформуванню, мало- або багато цикловому руйнуванню під силовим впливом, при протіканні теплових процесів та структурно-фазових перетворень, формуванню залишкових напружень різних знаків, спостерігається сумарний ефект силових, температурних та структурно-фазових залишкових напружень. The varieties of contact of triboelementov are considered tribo-element (TE), fortified composite material (CM) composition coating (CC), that allow substantially to change quality of physical contact, size of actual area, ability of superficial layer (SL) TE to the evolution of composition and structure in the process of friction and wear. The effective braking of motion of distributions the heterogeneous structures of CM(CC) is educed, both at subzero and at high temperatures, and also recrystallizations processes. The operating at a friction loading is distributed on hard fillers, that serve as opportune, barriers to movable distributions and reduce speed of flowage of matrix, that brings to the decline of intensity grasping over in a contact "matrix-matrix" and in a resiliently-plastic matrix there is relaxation of net voltages, minimum deformation and decline of probability of origin of cracks of tiredness. The tense state of material is considered TE of CM(CC) at a friction. The condition of plastic equilibrium of components as a system of equalizations and formula of size of tension are got in transition from material of filler to material of matrix and character of deformation is certain they are subject that. Expression for the critical angle of slope of performance and coefficient of friction and conducted estimation of change of coefficient of friction are got. In the process of friction and wear of SL CM(CC) subject to resiliently-plastic deformation, small- or much to cyclic destruction under power influence, at flowing of thermal processes and structurally-phase transformations, to forming of remaining tensions of different signs, there is a total effect of power, temperature and structurally-phase remaining tensions.