Вплив режимів експлуатації на зношування деталей, виготовлених з полімерно-композитного матеріалу

dc.contributor.authorАулін, В. В.
dc.contributor.authorДеркач, О. Д.
dc.contributor.authorМакаренко, Д. О.
dc.contributor.authorГриньків, А. В.
dc.contributor.authorAulin, V.
dc.contributor.authorDerkach, O.
dc.contributor.authorMakarenko, D.
dc.contributor.authorGrynkiv, A.
dc.date.accessioned2019-01-24T09:02:17Z
dc.date.available2019-01-24T09:02:17Z
dc.date.issued2018
dc.description.abstractЗазначено, що до посівних машин висуваються особливі вимоги: повне забезпечення якості посіву, висока надійність, ремонтопридатність у польових умовах, тривала перерва між технічними обслуговуваннями техніки тощо. Метою роботи є обґрунтування раціональних режимів експлуатації деталей, виготовлених з полімерно-композитного матеріалу. Для досягнення мети виконувались такі завдання: обґрунтувати закономірність зношування деталей рухомих спряжень в залежності від умов експлуатації та визначити раціональні режими їх роботи. Доведено, що основними факторами умов експлуатації, які впливають на триботехнічні характеристики рухомих з'єднань є навантаження, лінійна швидкість ковзання та зазор в спряженнях деталей. Виявлено, що суттєвий вплив на триботехнічні характеристики здійснює навантаження на трибоспряження деталей в той час, як відносна швидкість ковзання практично не впливає на них. Встановлено, що величина зазору в спряженні деталей при мінімальному значенні навантаження практично не змінюється величина зносу деталей. Мінімальне значення зносу становить (6,4 • 10-3 г) при наступних режимах експлуатації: Р = 250 Н та v = 0,1 м/с, S = 300 мкм. При розробці математичної моделі впливу режимів експлуатації на величину зношування, складали схему планування експерименту при трьох факторах: швидкість ковзання, навантаження та зазор у спряженнях зразків Отримана регресійна модель дозволяє оптимізувати параметри рухомих спряжень деталей в залежності від умов їх експлуатації. It was established that one of the main technological operations in growing any agricultural crop is sowing or planting. It is noted that special requirements apply to sowing machines: full quality assurance of sowing, high reliability, repair in field conditions, a long gap between maintenance of machinery and the like. The purpose of the work is to justify the rational modes of operation of parts made of polymer-composite material. To achieve the goal, the following tasks were performed: to substantiate the regularity of the wear of parts of moving conjugates depending on the conditions of operation and to determine the rational modes of their work. It is proved that the main factors of the operating conditions that affect the tribotechnical characteristics of the mobile connections are the load, the linear speed of sliding and the gap in the joints of the parts. It was revealed that significant influence on the tribotechnical characteristics carries the load on the detachment of three parts while the relative slip speed practically does not affect them. It is established that the size of the gap in the conjugation of parts with a minimum load value does not change the value of wear of parts. The minimum wear value is (6.4 ∙ 10-3 g) with the following operating modes: P = 250 N and v = 0.1 m / s, S = 300 microns. In developing the mathematical model of the influence of operating modes on the amount of wear, they compiled the scheme of planning the experiment in three factors: slip speed, load and gap in conjugation of samples. The obtained regression model allows to optimize the parameters of moving parts of the joints depending on the conditions of their operation.uk_UA
dc.identifier.citationВплив режимів експлуатації на зношування деталей, виготовлених з полімерно-композитного матеріалу / В. В. Аулін, О. Д. Деркач, Д. О. Макаренко, А. В. Гриньків // Проблеми трибології. - Хмельницький : ХНУ, 2018. - № 4. - С. 65-69.uk_UA
dc.identifier.issn2079-1372
dc.identifier.urihttps://dspace.kntu.kr.ua/handle/123456789/8335
dc.language.isouk_UAuk_UA
dc.publisherХНУuk_UA
dc.subjectпосівні машиниuk_UA
dc.subjectполімерно-композиційний матеріалuk_UA
dc.subjectшвидкість ковзанняuk_UA
dc.subjectзазорuk_UA
dc.subjectтриботехнічні характеристикиuk_UA
dc.subjectsowing machinesuk_UA
dc.subjectpolymer-composite materialuk_UA
dc.subjectslip speeduk_UA
dc.subjectclearanceuk_UA
dc.subjecttribotechnical characteristicsuk_UA
dc.titleВплив режимів експлуатації на зношування деталей, виготовлених з полімерно-композитного матеріалуuk_UA
dc.title.alternativeInfluence of operating modes on wear of parts made of polymer-composite materialuk_UA
dc.typeArticleuk_UA

Files

Original bundle
Now showing 1 - 1 of 1
Loading...
Thumbnail Image
Name:
Problems of Tribology 2018 № 4 P.65-69.pdf
Size:
238.48 KB
Format:
Adobe Portable Document
License bundle
Now showing 1 - 1 of 1
No Thumbnail Available
Name:
license.txt
Size:
7.42 KB
Format:
Item-specific license agreed upon to submission
Description: