Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація. Випуск 31. - 2018
Permanent URI for this collectionhttps://dspace.kntu.kr.ua/handle/123456789/8110
Browse
Search Results
Item Розмірна обробка електричною дугою бічної поверхні напрямного ролика з композиційного матеріалу на основі реліту(ЦНТУ, 2018) Сіса, О. Ф.; Пукалов, В. В.; Свяцький, В. В.; Сиса, О. Ф.; Свяцкий, В. В.; Sisa, O.; Pukalov, V.; Sviatskyi, V.Виконано обґрунтування технологічної схеми формоутворення зовнішньої бічної поверхні напрямного ролика, способом розмірної обробки електричною дугою з урахуванням особливостей фізичних механізмів їх утворення та гідродинамічних явищ в міжелектродному проміжку. Встановлені аналітичні зв’язки технологічних характеристик процесу розмірної обробки електричною дугою твердого сплаву «Реліт» з режимами обробки і геометричними параметрами. Выполнено обоснование технологической схемы формообразования внешней боковой поверхности направляющего ролика, способом размерной обработки электрической дугой с учетом особенностей физического механизма образования и гидродинамических явлений в межэлектродном промежутке. Установлены аналитические связи технологических характеристик процесса размерной обработки электрической дугой твердого сплава «Релит» с режимами обработки и геометрическими параметрами. The article is dedicated to development of technology and equipment of rough machining method by electric arc of a guide roller side surface, as high performance alternative to traditional methods of rough machining. During operation, the damage to the surface of the hard alloys guide roller caliber occurs by abrasion and chipping of carbide particles. The development of net shaped roll marks occurs by the occurrence of hotbeds of accelerated cluster abrasion and chipping of smaller particles with subsequent growth of these areas and unification in a closed net shaped roll marks. The turned out particles of hard alloy leave the machining marks on the wire, in such a worn the hard alloy rolling roller does not meet the specified dimensions and it is reground to a smaller diameter by grinding of diamond tool on the rough machining stage. It is proposed on the stage of rough machining to remove the worn-out profile of a guide roller side surface with help of dimensional electric arc, which allows you to remove big allowances of material at the lowest treatment costs. It is suggested to get the lateral surface by dimensional electric arc with a given roughness of Ra = 10..20mkm, which allows you to take great allowances material at the lowest cost processing time.In this case, the processing cycle of hard alloy side surface decreased of 1,4…2,6 times. The justification of technical scheme of forming the guide roller side surface by electric arc sizing method is done taking into account features of physical formatting mechanism and hydrodynamic phenomena in the electrode gap. The analytical communication of technological characteristics of rough machining process by electric arc made of composite material, based on relit, with the modes of processing and geometric parameters are established. The obtained models allow to control the productivity and specific productivity, specific electricity consumption, quality and surface accuracy which is processed, predicted and optimized given characteristics. A technical solution is proposed that allows to expand the technological possibilities of processing the guide roller.Item Виробничі випробування технології механізованого компостування органічних відходів з використанням аератора-змішувача(ЦНТУ, 2018) Павленко, С. І.; Павленко, С. И.; Pavlenko, S.Проведений системний аналіз поводження з органічними відходами, існуючий в господарстві на фермі великої рогатої худоби стійлового утримання. Результати аналізу узагальнені у вигляді таблиці, що розглядає технологічний процес, операції та склад технічних засобів та матеріалів і значення показників операції. Сформовані робочі гіпотези по покращенню технології поводження з органічними відходами на основі вдосконалення технологічних прийомів циклу, яким необхідно повести експериментальну перевірку: ‒ формування буртів при суцільному складуванні гноєвих сумішей за рахунок створення проходів шириною до 2-3 м в середовищі сировини вологістю до 75 % за допомогою бульдозера або іншого технічного засобу; ‒ формування буртів при вивантаженні гноєкомпостної суміші на майданчик при транспортуванні сировини самоскидним тракторним причепом або розкидачем органічних добрив, що агрегатуються з трактором МТЗ-80; ‒ укрупнення буртів з використанням бульдозера; ‒ покращення аерації за рахунок використання аератора-змішувача, конструкції ІМТ НААН України. Розроблений вдосконалений технологічний і технічний регламенти механізованого компостування. Визначені геометричні параметри буртів, їх щільність, маса. Проведені результати випробування технічних засобів: бульдозера, аератора-змішувача згідно стандартним методикам. Проведенный системный анализ поведения с органическими отходами, существующий в хозяйстве на ферме крупного рогатого скота стойлового содержания. Результаты анализа обобщены в виде таблицы, рассматривает технологический процесс, операции и состав технических средств и материалов и значения показателей операции. Сформированы рабочие гипотезы по улучшению технологии обращения с органическими отходами на основе совершенствования технологических приемов цикла, которым необходимо повести экспериментальную проверку: - формирование буртов при сплошном складировании гноя смесей за счет создания проходов шириной до 2-3 м в среде сырья влажностью до 75% с помощью бульдозера или другого технического средства; - формирование буртов при выгрузке гноекомпостнои смеси на площадку при транспортировке сырья самосвальным тракторным прицепом или разбрасывателем органических удобрений, которые агрегатируются с трактором МТЗ-80; - укрупнение буртов с использованием бульдозера; - улучшение аэрации за счет использования аэратора-смесителя, конструкции ИМТ НААН Украины. Разработан усовершенствованный технологический и технический регламенты механизированного компостирования. Определены геометрические параметры буртов, их плотность, масса. Проведенные результаты испытания технических средств: бульдозера, аэратора-смесителя согласно стандартным методикам. Adaptation of new technological methods and technical means of mechanized composting of organic waste of bovine cattle at steady maintenance and daily disposal of organic waste requires systemic solutions based on the analysis of organizational and economic conditions. In practical terms, it is necessary to prove the feasibility of introducing modern solutions: technologies, technical means, methods of use before existing in the economy. The purpose of the further development of rational use of technical means in the mechanized processes of solid phase composting. A systematic analysis of the management of organic waste, existing in the farm on the cattle stockholding system, was carried out. The results of the analysis are summarized in the form of a table that deals with the technological process, operations and the composition of the technical means and materials and the value of the indicators of the operation. Worked hypotheses for improving the technology of handling organic waste based on the improvement of technological techniques of the cycle, which need to conduct an experimental verification: - the formation of bursts in the continuous storage of gnawing mixtures due to the creation of passages with a width of up to 2-3 m in the medium of raw materials up to 75% humidity using a bulldozer or other technical means; - formation of bursts during unloading of gnoyeposobnoy mixture at the site during transportation of raw material by a dumper tractor trailer or spreader of organic fertilizers that are aggregated with a tractor MTZ-80; - consolidation of bursts using a bulldozer; - Improvement of aeration due to the use of an aerator-mixer, the structure of the IMT NAAS of Ukraine. Improved technological and technical regulations for mechanized composting have been developed. The geometric parameters of the drums, their density, mass are determined. The results of testing the technical equipment: bulldozer, mixer aerator according to standard methods are carried out. Main conclusions. Formation of passages in the raw material, which is enclosed entirely with the help of a bulldozer, is not efficient. Previously, it is necessary to form bursts when unloading in a row. The technological complex of technical means ensures high-quality mixing, formation of drills in height and width, new aggregates are created - the size of particles close to the soil aggregates. The cycle is up to 45-60 days. Productivity of the unit: tractor MTZ-80 with throttle reducer from 300 to 500 t / year. Smaller values at first passages. Working speeds 0,10-0,25 m / s. Technological operations of accelerated composting can increase the chemical composition of organic fertilizers by 20-30%, reduce the loss of nutrients, increase the mass of organic fertilizers, introduced on the field by 60-70%.