Конструювання, виробництво та експлуатація сільськогосподарських машин. Випуск 51. - 2021
Permanent URI for this collectionhttps://dspace.kntu.kr.ua/handle/123456789/11876
Browse
Search Results
Item Обґрунтування конструктивної схеми пневморешітного сепаратора зерна(ЦНТУ, 2021) Васильковський, О. М.; Лещенко, С. М.; Нестеренко, О. В.; Петренко, Д. І.; Якименко, С.М.; Vasylkovskyi, O.; Leshchenko, S.; Nesterenko, O.; Petrenko, D.; Iakymenko, S.Статтю присвячено удосконаленню конструкції відцентрового пневморешітного сепаратора для розділення компонентів зернових сумішей. Базова конструкція задовільно виконує технологічний процес, однак має відносно великі вертикальні габарити за рахунок використання замкненої системи аспірації з подвійним очищенням зернової маси повітряним потоком. В роботі наведено концепцію удосконалення системи аспірації, що дозволить суттєво зменшити висоту, а також викладено методику проектного конструкторського розрахунку параметрів удосконаленої машини. The aim of the article is to improve the design of the original centrifugal grain separator. The separator is designed to separate the components of grain materials by size and aerodynamic properties. The basic design satisfactorily performs the technological process, but has large dimensions vertically. Reducing the size will simplify the design and reduce the cost of the machine. The article proposes to replace the double pneumatic cleaning of grain material with a single one. At the same time the car gets rid of the closed aspiration system. The closed aspiration system has operational advantages, however difficult adjustment reduces indicators of technological efficiency of pneumatic cleaning of grain. The original pneumatic cleaning system allows you to remove light impurities without creating significant air resistance, due to the lack of countercurrent movements. In addition, the use of an inclined pneumatic channel does not require the creation of high-speed airflow. As a result of the proposed improvement simplifies the structure and regulation of the separator, as well as reduces its size and weight. In addition to the modernization of the design of the pneumatic-sieve separator, the article presents the method of design engineering calculation of its basic geometric parameters. Depending on the specific capacity of the upper (ear) sieve and the characteristics of the grain mixture is determined by its length and angle. The remaining geometric parameters are derived from the above. Based on preliminary calculations, the following conclusions can be drawn. The use of the proposed scheme will reduce the height and weight of the centrifugal pneumatic sieve grain separator. Replacing the double air cleaning with a single one will simplify the adjustment of the machine. Experimental establishment of indicators of technological efficiency of the proposed separator will theoretically determine the dimensions and automate the design process of grain cleaning machines created by a similar scheme.Item Теоретичні дослідження руху компонентів зернового матеріалу із штучно сформованим розподілом швидкості повітря в поперечному перетині каналу(ЦНТУ, 2021) Котов, Б. І.; Степаненко, С. П.; Kotov, B.; Stepanenko, S.В статті розглядаються дослідження поділу зернових матеріалів у пневматичних каналах із штучно сформованим розподілом швидкості повітря в поперечному перетині каналу, для визначення раціональної форми та параметрів подачі матеріалу та варіантів поділу зернового матеріалу на фракції. Теоретично досліджено та встановлено закономірності руху зернівки у вигляді математичних моделей динаміки руху твердої частки в потоці повітря, які відрізняється від відомих тим, що враховують дію бокових сил, концентрацію матеріалу, а застосування степеневого закону та штучно сформованого експоненціального закону розподілу повітря дало можливість підвищити розходження (розщеплення) траєкторій руху зернівок на 20%. Розв’язок системи нелінійних диференційних рівнянь із початковими умовами виконано в програмному середовищі MathCad у вигляді траєкторій руху зернівки в повітряному потоці, що дозволяє розраховувати їх траєкторії руху, які різняться коефіцієнтами парусності та визначити раціональні значення параметрів пневмогравітаційних та пневмоінерційних сепараторів. Використовуючи отримані залежності для розробки повітряних сепараторів, можна визначити початкову швидкість введення і напрямок входження зернівок у повітряний потік, а також визначити траєкторії руху матеріалу в повітряних каналах з нижнім вивантаженням матеріалу. The purpose of research to formulate a mathematical description of the movement of components of grain material in pneumatic channels with artificially formed distribution of air velocity in the cross section of the channel to improve the quality of separation (trajectory divergence) of grain material components. The article considers studies of grain separation in pneumatic channels with artificially formed air velocity distribution in the cross section of the channel, to determine the rational form and parameters of material supply and options for separation of grain material into fractions. The regularities of grain motion in the form of mathematical models of the dynamics of solid particle motion in air flow are theoretically investigated and established, which differ from those known in that they take into account the action of lateral forces, material concentration, and the application of power law and artificially formed exponential air distribution law) trajectories. The solution of the system of nonlinear differential equations with initial conditions is made in the MathCad software environment in the form of grain motion trajectories in air flow, allows to calculate their motion trajectories that differ in sailing coefficients and determine rational values of pneumogravity and pneumoinertia parameters. Using the obtained dependences for the development of air separators, it is possible to determine the initial velocity of entry and direction of entry of grains into the air stream, as well as to determine the trajectories of the material in the air ducts with lower material unloading. Conclusions: 1. Theories of grain motion are theoretically investigated and established in the form of mathematical models of solid grain motion dynamics in air flow, which differ from those known in that they take into account the action of lateral forces, material concentration, and the application of power and artificial exponential law (splitting) of grain movement trajectories by 20%. 2. The solution of the system of nonlinear differential equations with initial conditions is made in the MathCad software environment in the form of grain motion trajectories in the air stream, which allows to calculate their motion trajectories differing in sailing coefficients and determine rational values of pneumogravity and pneumoinertial separators.