Наукові публікації кафедри БДМБ
Permanent URI for this collectionhttps://dspace.kntu.kr.ua/handle/123456789/1353
Browse
11 results
Search Results
Item Providing the thermal reliability of window junctions during the thermal modernization of civil buildings(2020) Pashynskyi, M.; Dzhyrma, S.; Pashynskyi, V.; Nastoyashchiy, V.; Пашинський, М. В.; Джирма, С. О.; Пашинський, В. А.; Настоящий, В. А.In order to assess the possibility of condensation on an internal window jamb surface, the temperature fields of window junctions to brick and precast concrete walls of civil buildings were analyzed, which were massively produced in the second half of the twentieth century. This study obtained the dependences of the jamb temperature on the thickness of the additional insulation layer and the outdoor temperature. Additionally, it showed the possibility of adjusting the jamb temperature by shifting the window frame inside the building. Outside air temperatures at which no condensation will occur in the initial junction structures and after thermal modernization by additional facade insulation were determined. The results can be used to replace worn-out windows and during the thermal modernization of buildings.Item Досвід розрахунково-екпериментального оцінювання енергетичних показників будівлі школи(НУВГП, 2020) Настоящий, В. А.; Пашинський, В. А.; Пашинський, М. В.; Джирма, С. О.; Nastoiashchyi., V.; Pashynskyi, V.; Pashynskyi, M.; Dzhyrma, S.Висвітлена методика і результати оцінювання показників енергетичної ефективності будівлі школи з урахуванням теплових характеристик огороджувальних конструкцій, отриманих за даними вимірювань у процесі натурних обстежень. Проаналізовано вплив термомодернізації на клас енергетичної ефективності будівлі. During the examination, numerous damages of the outer wall cladding, unfilled seams between the wall blocks and poorly executed junction of window and door frames to a wall were revealed, where heat transfer is highly increased due to air leakage from the inside of the building. The actual values of the heat transfer resistance of walls and translucent structures, experimentally established using a thermohygrometer, do not meet the requirements of current standards. Examination of the outer walls and window blocks using a thermal imager revealed thermal anomalies that significantly reduce the thermal insulation characteristics of enclosure structures. It is noted that the use of technical devices makes it easy to detect thermal anomalies and to estimate the characteristics of enclosure structures. Based on the research results, an energy passport of the building was developed. The design value of specific energy consumption is 55.7 kW×h/m3. Taking into account the maximum value of 35 kW×h/m3 for educational institutions, that are a subject of thermal modernization, the building was examined and classified as energy efficiency class F. Design proposals have been developed for thermal modernization of the building by using ventilated facade systems with rockwool insulation. After thermal modernization, the specific energy consumption are reduced to 34.7 kW×h/m2, and the energy efficiency is improving to class C.Item Методика аналізу процесу теплопередачі у вузлах огороджувальних конструкцій будівель(ОДАБА, 2020) Джирма, С. О.; Пашинський, В. А.; Настоящий, В. А.; Пашинський, М. В.Розроблена методика визначення втрат тепла через вузли огороджувальних конструкцій довільної форми. Методика базується на аналізі температури внутрішньої поверхні огороджень і дозволяє визначати втрати тепла в зонах лінійних теплопровідних включень та відповідні лінійні коефіцієнти теплопередачі. Встановлені параметри чисельного розв'язку, які гарантують достатню точність результатів. Виконані приклади визначення втрат тепла та лінійних коефіцієнтів теплопередачі для характерних вузлів стін житлових і громадських будівель. Достовірність результатів підтверджена шляхом порівняння лінійних коефіцієнтів теплопередачі з відомими даними для типових вузлів. The energy needs of buildings should be determined taking into account heat losses through zones of increased thermal conductivity in the junctions of enclosure structures. For this, linear heat transfer coefficients are used, which are given in the Ukrainian standard for a number of typical junctions. Non-standard solutions of junctions of enclosure structures require the development of a simple method for determining heat loss, which can be used for the design of real buildings. The proposed method is based on the analysis of the process of heat transfer from internal air to the inner surface of the enclosure. To determine the amount of heat, it is necessary to select a junction with adjacent flat sections of the enclosure and by two-dimensional computer simulation to determine the temperature on the inner surface of the enclosure. The amount of heat transferred is determined by numerical integration of the temperature difference between the internal air and the inner surface of the enclosure, taking into account the heat transfer coefficient of this surface. By the multi-variant calculations, it was found that the width of the adjacent junctions to the flat wall sections should be about two thicknesses of the wall. For a sufficiently accurate determination of heat loss using the trapezoidal rule, the discretization step of the temperature of the inner surface should not exceed 40 ... 50 mm. The developed technique also allows to determine the linear heat transfer coefficient of the junction. It is equal to the difference between the total amount of heat transferred and the amount of heat that can be transmitted through the flat sections of the enclosure, divided by the temperature difference between the internal and external air. A comparison of the obtained results with the values of linear heat transfer coefficients known from the Standard for several typical wall units showed a discrepancy within 2.5%. Such accuracy level can be considered as satisfactory for the thermal calculations of enclosure structures. Given the ease of implementation, the developed method is recommended for use during calculations of the energy performance of buildings.Item Обоснование использования самофутеровки рабочих поверхностей для повышения показателей барабанных мельниц(УкрДАЗТ, 2014) Настоящий, В. А.; Чижик, Е. Ф.; Тихий, А. А.; Настоящий, В. А.; Чижик, Є. Ф.; Тихий, А. А.; Nastoyashchiy, V.; Chizyk, E.; Tykhyi, A.В работе с использованием моделирования связности, базирующемся на топологических операциях объединения и разъединения твердых тел, в качестве которых рассматриваются мелющие шары и футеровочные плиты. При этом допускается преобразование связности, совместно с конфигурацией при размещении, деформируемость одного из тел, их объединение и разъединение. Решается задача определения параметров самофутеруюшихся плит рабочих поверхностей барабанных мельниц, обеспечивающих повышение производительности мельниц при сохранении срока службы. В роботі з використанням моделювання зв’язності, яке базується на топологічних операціях об’єднання і роз’єднання твердих тіл, в якості яких розглядались подрібнюючі кулі і футерувальні плити. При цьому допускалось перетворення зв’язності, сумісність конфігурації при розміщенні, дефомованість одного з тіл, їх об’єднання та роз’єднання, вирішується задача визначення параметрів робочих поверхонь плит, барабанних млинів плит, що самофутеруються, для забезпечення підвищення продуктивності млинів при збереженні термінів служби. The most important operation in the technology of preparation of mineral raw materials for the production of construction materials on the enterprises of the construction industry is grinding, mainly carried out in the drum mills. An important place in the context of increasing productivity while reducing energy mills takes protective lining working surface. One of the factors designed to enhance performance and service life of mill liners is a character interaction processing load of the working surface of the lining and the drum mill in which the contact zone formed in the layer of crushed material or specially placed metal balls. To this end, members of the lining constructively carried out with special recesses or niches. In the work carried out theoretical studies on the characterization of lining plates, provide reliable jamming balls. For this purpose we used simulation of connectivity based on topological operations of union and separation of solids, which were considered as the grinding balls and lining plates, while allowing the transformation of the connection, the joint configuration for the location, the deformability of one of the bodies, their union and separation. As a result, provides guidance on determining the parameters of the working surfaces of the plates self- lining tumbling mills, mills that boost productivity while maintaining durability.Item Design validation of the working surface of a sheep’s foot roller for compaction of freshly prepared soil(Magnolithe GmbH, 2018-02-11) Artemenko, D.; Nastoyaschiy, V.; Darienko, V.; Артеменко, Д. Ю.; Настоящий, В. А.; Дарієнко, В. В.It is determined that the main factors which influence the process of soil compaction are the design of the roller working element and physical and mechanical characteristics of the soil. The process of interaction between the roller and the soil was studied with the help of math modelling. It was defined that the character of the contact pressure distribution under the roller surface corresponds to its design characteristics. A modified design of the roller drum and foot was introduced.Item Вплив положення віконних блоків по товщині стіни на теплотехнічні характеристики вузла їх примикання(Global Science Center LP, 2017) Пашинський, В. А.; Настоящий, В. А.; Джирма, С. О.; Плотніков, О. А.; Остапчук, А. С.; Pashynskyi, V.; Nastoyashchiy, V.; Dzhyrma, S.; Plotnikov, O.; Ostapchuk, A.Однією з вагомих складових втрат тепла через огороджувальні конструкції будівель є вікна та вузли їх примикання до стін. Проведені дослідження дозволили визначити положення вікна в товщі стіни, яке забезпечує оптимальний тепловий режим вузла примикання вікна до стіни в заданих кліматичних умовах експлуатації. Результати дослідження можуть бути основою для створення загальної методики визначення оптимального положення вікон різних типів у зовнішніх стінах різних конструкцій, що експлуатуються в різних кліматичних умовах. Впровадження результатів зменшить втрати тепла в вузлах примикання вікон та забезпечить відсутність конденсації вологи в зоні цих вузлів. One of the significant components of heat loss through the enclosure structures of buildings is the windows and junction nodes to the walls. The conducted researches allowed to determine the position of the window in the thickness of the wall, which provides the optimal thermal mode of the node, that connects the window to the wall in the given climatic conditions of operation. The results of the research may be the foundation for creating a methodology for determining the optimal position of windows of different types in the outer walls of different designs, operated in different climatic conditions. Implementation of the results will reduce the heat losses in the in the nodes of windows to the outer walls and ensure the absence of condensation in the zone of these nodes.Item О выборе критерия для прогнозирования износостойкости эластомерных покрытий транспортирующих и перегрузочных сооружений предприятий горно-металлургического комплекса(ОДАБА, 2013) Настоящий, В. А.; Яцун, В. В.; Джирма, С. А.; Чижик, Е. Ф.; Настоящий, В. А.; Яцун, В. В.; Джирма, С. О.; Чижик, Є. Ф.; Nastoyashchiy, V.; Yatcun, V.; Dzhyrma, S.; Chizhik, E.В работе обосновывается методика прогнозирования износостойкости эластомерных покрытий транспортирующих и перегрузочных сооружений предприятий горно-металлургического комплекса на основе термофлуктуационной теории разрушения полимерных материалов. Приведена теоретико-экспериментальная информация, необходимая для расчета износостойкости и долговечных полимерных футеровок. Methodology of prognostication of wearproofness of elastomeric coverages of transporting and shifting building of enterprises of mining and metallurgical complex is in-process grounded on the basis of theory of destruction of polymeric materials. The teoretiko-experimental information necessary for calculation of wear resistance and durable polymeric linings is provided.Item Разработка синергетической модели взаимодействия перерабатываемого и транспортируемого сырья с резиновыми покрытиями поверхностей конструкций предприятий горно-металлургического комплекса(ОДАБА, 2012) Настоящий, В. А.; Яцун, В. В.; Джирма, С. А.; Чижик, Е. Ф.; Настоящий, В. А.; Яцун, В. В.; Джирма, С. О.; Чижик, Є. Ф.; Nastoyashchiy, V.; Yatcun, V.; Dzhyrma, S.; Chizhik, E.В работе обосновывается синергетическая модель взаимодействия перерабатываемого и транспортируемого сырья с резиновой футеровкой конструкций, отображающая физико-механические эффекты, происходящие в зоне контакта загрузка-футеровка. Приведена теоретико-экспериментальная информация, необходимая для расчета и создания износостойких и долговечных резиновых футеровок. The work gives grounds to the synergetic model of the feed and transported stock cooperation with rubber lining of designs. If represents physical and mathematical effects that take place in the con-tact zone load lining. It is given theoretical and experimental data ne-cessary for designing wearproof and durable rubber lining.Item Порівняльна оцінка зносостійкості сталевих і гумових покриттів поверхонь конструкцій підприємств гірничо-металургійного комплексу при ударних навантаженнях(ОДАБА, 2017) Настоящий, В. А.; Яцун, В. В.; Nastoyashiy, V.; Yatsun, V.В якості футеровочних матеріалів поверхонь, які безпосередньо контактують з матеріалом, що переробляється, у бункерах, рудоспусках, перевантажувальних вузлах широко використовуються зносостійкі гуми. Подальше впровадження гумованих покриттів замість металевих стримується відсутністю методик інженерних розрахунків, що обґрунтовують умови, при яких зносостійкість гумових покриттів поверхонь транспортуючих і перевантажувальних споруджень підприємств гірничо-металургійного комплексу, які працюють в умовах ударного вантаження, не поступається металевим покриттям. Для визначення критерію порівняння зносостійкості гумових і металевих покриттів по відношенню до ударних навантажень використана класична теорія Герца пружного зіткнення тіл, на основі якої для випадку навантаження покриття частками, що ударяють по перпендикуляру до його поверхні, отримано вираження для критичної швидкості зіткнення, при якій досягається межа міцності матеріалу покриття. Таким чином, задаючись умовами навантаження покриття (щільність матеріалу і радіус падаючих абразивних часток, коефіцієнти Пуассона для часток і покриття, відповідні модулі Юнга для часток і покриття; швидкість часток перед зіткненням) визначаються умови, при яких зносостійкість гумових покриттів поверхонь транспортуючих і перевантажувальних споруджень підприємств гірничо-металургійного комплексу які працюють в умовах ударного вантаження, не поступається металевим покриттям, що дозволяє більш обґрунтовано підходити до вибору матеріалу захисних покриттів устаткування і конструкцій. As lining-up materials of surfaces of bunkers, lowering of ore, shifting knots directly contacting with the processed material, wearproof rubbers are widely used. Further introductions of rubberized coat instead of metallic restrains temper absence of methodologies of engineering calculations, grounding terms at that wearproofness of rubber coverages of surfaces of transporting and shifting building of enterprises of mining and metallurgical complex working in the conditions of shock ladening, does not yield to metallic coverages. For determination of criterion of comparison of wearproofness of rubber and metallic coverages in relation to the shock loading the classic theory resilient collision of bodies of Hertz is used, on the basis of that for the case of ladening of coverage particles striking on a perpendicular to his surface, expression is got for stalling speed of collision, at that tensile of material of coverage strength is arrived at. Thus, set by the terms of ladening of coverage (closeness of material and radius of falling abrasive particles, coefficients of Poisson for particles and coverage, corresponding modules cabin of Jung Boy for particles and coverage; speed of particles before hitting) may be determine terms at that wearproofness of rubber coverages of surfaces of transporting and shifting building of enterprises of mining and metallurgical complex working in the conditions of shock ladening does not yield to metallic coverages, that allows it is more reasonable to go near the choice of material of sheeting of equipment and constructions.Item Анализ причин образования начальных усталостных повреждений резиновых покрытий поверхностей конструкций предприятий горно- металлургического комплекса(ОДАБА, 2016) Настоящий, В. А.; Чижик, Є. Ф.; Яцун, В. В.; Nastoyashchiy, V.; Chizyk, E.; Yatsun, V.Гипотеза причин образования начальных усталостных повреждений резиновых покрытий поверхностей обоснована на том, что процесс износа полимерных материалов вследствие ударов абразивных частиц и кусков транспортируемого материала, но включает в себя термические превращения, вызванные термическим пиролизом. Такой подход позволяет обосновано подходить к выбору марок резин футеровочных материалов рабочих поверхностей бункеров, рудоспусков, перегрузочных узлов и других конструкций. The hypothesis of reasons of formation of initial tireless damages of rubber coverages of surfaces is reasonable on that process of wear of polymeric materials because of shots of abrasive particles and pieces of the transported material, but plugs in itself the thermal transformations caused by thermal pyrolysis. Such approach allows it is reasonable to go near the choice of brands of rubbers of the refractory-lined materials of working surfaces of bunkers, рудоспусков, shifting knots and other constructions