Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
14 results
Search Results
Item type:Item, До розрахунку зубців прямозубих циліндричних передач на згин(ЦНТУ, 2020) Невдаха, Ю. А.; Дубовик, В. О.; Невдаха, Н. А.; Златопольський, Ф. Й.; Nevdakha, Yu.; Dubovyk, V.; Nevdakha, N.; Zlatopolskiy, F.; Дубовик, В. А.; Златопольский, Ф. И.В роботі аналізуються розрахункові схеми циліндричної прямозубої передачі на згин зубців. Розглядається найбільш поширена розрахункова схема злому зубця, де небезпечний переріз злому зуба відбувається у основі ножки вище кола діаметра западини зубців. На практиці реальний же злом зубця лежить нижче діаметра западини зубців і має опуклу форму перерізу. Для більш точного розрахунку зубців на згин досліджували коефіцієнт форми зубців. В результаті встановлено, що коефіцієнт форми зуба зменшується зі збільшенням кількості зубців. The aim of the work is to improve the calculations of spur cylindrical wheels per bend, due to the fact that the existing formulas do not give the actual value of the maximum stress, and the diagram does not correspond to the real law of stress distribution. In order to obtain satisfactory results, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients and substantiating the calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth, to obtain formulas for the bending strength of the teeth of the gear and wheel. When calculating the bending teeth, the calculation is based on the stresses arising at the base of the tooth, under the load applied at the top of the tooth. Consider first the most common calculation scheme. Dangerous section of the tooth as seen from the plot of total stresses indicates that the maximum normal stress occurs on the non-working side of the tooth - the compression side, however, since fatigue cracks occur at the base of the tooth on the stretching side, the calculation is based on tensile stress on the working side. The hypothesis of non-curvature of flat sections is unfair for short beams of variable cross section, so the total diagram does not correspond to the real law of stress distribution. But at the base of the tooth near the transition curve is the place of stress concentration. The actual dangerous cross-section lies below the cross-section of the depression, this is confirmed by the fact that the fatigue cracks form an angle with the load curve close to straight, and the fracture of the tooth has a convex shape. In this case, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients obtained a calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth. As a result of the study it was found that the coefficient of tooth shape decreases with increasing number of teeth. This result was expected because as the number of teeth increases, the angle between the teeth decreases, and neighboring teeth perceive part of the stress that occurs in the loaded tooth. The formulas for checking the bending strength of gear teeth and wheels are obtained. The above refinement calculations of the teeth on the bend reflect the beneficial effect of improving the accuracy of the manufacture of teeth. В работе анализируются расчетные схемы цилиндрической прямозубой передачи на изгиб зубцов. Рассматривается наиболее распространенная расчетная схема излома зубцов, где опасное сечение излома зубьев происходит в основе ножки выше круга диаметра впадины зубцов. На практике реальный же излом зубьев лежит ниже диаметра впадины зубьев и имеет выпуклую форму сечения. Для более точного расчета зубьев на изгиб исследовали коэффициент формы зубьев. В результате установлено, что коэффициент формы зуба уменьшается с увеличением количества зубьев.Item type:Item, Комп’ютерне моделювання процесу прямого пресування через різні профілі матричних лійок(ЦНТУ, 2020) Свяцький, В. В.; Скрипник, О. В.; Конончук, С. В.; Sviatskyi, V.; Skrypnyk, O.; Kononchuk, S.; Свяцкий, В. В.Виходячи з аналізу напруженого і деформованого стану стадії пресування, що встановилася, запропоновано використовувати профіль матричної лійки, виконаний по лінії ковзання, що розділяє пружну і пластичну зону. Результати теоретичних досліджень, комп’ютерного моделювання процесу прямого пресування за допомогою програмного комплексу Deform 2D/3D, експериментальних дослідів показали, що кращі умови пресування досягаються через матрицю із профілем, який виконаний по лінії ковзання. The stressed and deformed state of the metal and the dimensions of the center of deformation during pressing depend significantly on the design of the tool and, in particular, on the shape of the matrix funnel. However, there is still no single point of view on the influence of the geometry of the deformation center on the energy forces of the metal pressing process. Based on the analysis of the field of slip lines of the steady-state stage of pressing through a symmetric single-point matrix, it is proposed to use the profile of the matrix funnel made along the slip line separating the elastic and plastic zones. The following types of matrix funnel profiles were investigated using computer simulation of direct extrusion of lead samples with a drawing value 81 at a speed of 1 mm/s: cycloid concave; convex; the second convex, which is built on the logarithmic dependence; conical and concave, which is built along a sliding line that separates the elastic zones from the plastic in the pressing process. The results of theoretical studies, computer simulations of the direct pressing process using the Deform 2D/3D software package, and experimental experiments have shown that optimal energy-power conditions are achieved by pressing through a matrix that has a profile made along the slip line. The results of the experimental study of the kinetics of the flow of the discrete medium showed that the shape of the matrix funnel influences the size of the deformation center and the distribution of the resulting deformation in the molding. From the analysis of deformation of the granules, it is determined that the concave funnel, built along the slip line, is characterized by a curvature of the axisymmetric particles in the direction of deformation. These curvatures decrease as the granules move to the axis of symmetry of the matrix. It is noted that for a convex funnel, the length of the deformation center is greatest; for a conical metal flow is close to the radial in the direction of the truncated cones. На основе анализа поля линий скольжения установившейся стадии прессования через симметричную одноочковую матрицу предложено использовать профиль матричной воронки, выполненный по линии скольжения, разделяющий упругую и пластическую зону. Результаты теоретических исследований, компьютерного моделирования процесса прямого прессования с помощью программного комплекса Deform 2D/3D, экспериментальных опытов показали, что оптимальные энергосиловые условия достигаются при прессовании через матрицу, которая имеет профиль, выполненный по линии скольжения.Item type:Item, До визначення швидкості ковзання та зусилль, які діють в зачепленні черв’ячної передачі(ЦНТУ, 2017) Невдаха, Ю. А.; Дубовик, В. О.; Невдаха, А. Ю.; Пукалов, В. В.; Nevdaha, Y.; Dubovik, V.; Nevdaha, А.; Pukalov, V.В статті розглянута величина швидкості ковзання і її напрям відносно лінії дотикання черв’яка і черв’ячного колеса, визначені швидкості ковзання та зусилля, які діють в зачепленні. The purpose of the article is to investigate ways to increase the durability and tractive ability of worm gears. Improve the durability of worm gears by improving the working environment, as well as by applying an oil wedge. One of the ways to increase the pressure in the oil wedge, as well as increasing the loading capacity of the transmission is to change the geometry of the clutch. The article considers the value of the slip speed and its direction relative to the line of contact of the worm and worm wheel. The sliding speeds and forces that are in contact are determined. The peculiarity of a worm gear is slipping along the teeth. The magnitude of the slip velocity and its direction relative to the line of contact between the two bodies moving relative to each other, as well as the shape of the tangential surfaces, largely determine the hydrodynamic conditions of the engagement and, consequently, affect the performance of the transmission. Investigating the speed of sliding in worm gears it was found that the speed of movement of the contact line relative to the tooth of the worm wheel was small compared with the speed of the worm worm. The values of the angles formed by contact lines with directions for different points of the worm vary in a wide range. It was established that conditions for the formation of an oil wedge deteriorate with a decrease in the angle of recovery of a worm turn.Item type:Item, Дослідження міцності елементів різьби(КНТУ, 2006) Невдаха, Ю. А.; Маломуж, Г. І.; Хіоні, В. З.В статті проведений аналіз причини руйнування елементів різьби болтових з’єднань пов’язаного з впливом відношення висоти гайки до діаметра гвинта L/d та діаметра гвинта до кроку різьби d/S. In the article there is the conducted analysis of reason of destruction of elements of screw-thread of screw-bolt connections of related to influencing relation of height of nut to the diameter of screw L/d and diameter of screw to the step of screw-thread d/S.Item type:Item, Дослідження зусиль, які діють на робочу частину наральникових сошників(КНТУ, 2006) Бойко, А. І.; Харьковський, І. С.; Свірень, М. О.В статті розглянуті епюри напруження, які діють на робочу частину наральникового сошника. Приведені рівняння для визначення складових зусиль опору переміщення і сили, які обумовлюють зношування поверхонь сошника. In the article the considered epures tensions which operate on working part of naral'nykovogo soshnyka. Resulted equalizations for determination of component efforts of resistance moving and forces which stipulate the wear of surfaces of soshnyka.Item type:Item, Вплив розміру зернівок на їх міцність і якість насіння(2015) Котков, В. І.; Пустовіт, Л. В.; Kotkov, Volodimyr; Pustovit, LudmylaВикладено методику визначення впливу розміру зернівок на їх міцність, та терміну зберігання насіння озимої пшениці Поліська 90 на її посівні якості. The aim of this work is to determine the effect of grain size on the strength and sowing qualities of seeds, and the dependence of its contamination by pathogens from its shelf. A method of determining the influence of grain size on the strength and duration of storage of seeds of winter wheat Polesskaya 90 on its sowing qualities. Studies have shown that with increasing the width of the holes of the sieve effort of destruction mirror nvoc grows, the rupture strain decreases and decreases and the ratio of the strain to fracture width.Item type:Item, Фахове супроводження змін у топографіях контактних поверхонь робочих деталей штампів холодного об’ємного штампування(КНТУ, 2008) Кришкін, Б. Б.У статті наведені результати дослідження методики прогнозування довговічності робочих деталей штампів під час виконання ними штампувальних операцій. Представлені основні математичні залежності, що визначають окислювальне зношування та руйнування інструменту. Запропоновано практичне застосування зазначеної методики під час процедур фахового супроводження і проектування оснащення для холодного об’ємного штампування. In the article the results of development and research for the surface structure and properties cold upsetting tool engineering monitoring are stated. Scheme and consecutivity of cold upsetting tool longevity depending of deformed steels figures are presented. The practical applications of the described method in production conditions are proposed.Item type:Item, Моніторинг процесів тріщиноутворення в робочих деталях технічних систем ковальсько-штампувального виробництва(КНТУ, 2008) Кришкін, Б. Б.; Деменський, Д. І.; Сімончик, Є. О.У статті наведені результати дослідження і оцінки методики прогнозування тріщиностійкості елементів конструкції технологічного оснащення під час виконання штампувальних операцій. Представлені основні математичні залежності, що визначають поведінку тріщини. Запропоновано практичне застосування зазначеної методики під час процедур фахового супроводження і проектування технічних систем ковальсько-штампувального виробництва. In the article is given the results of research and estimation of metal forming technical systems elements and knots failure prognosis method. The basic mathematical expressions of failure conditions are represented. Practical using of these methods during the profile monitoring of forming equipment are proposed.Item type:Item, Моделювання інтенсивності експлуатації пуансонів холодного видавлювання за допомогою програмного комплексу DEFORM v.10(КНТУ, 2011) Кришкін, Б. Б.; Мірзак, В. Я.; Ставерська, О. Е.; Черпак, А. О.; Kryshkin, B.; Mirzak, W.; Staverskaya, О.; Cherpak, А.У статті наведені результати моделювання температурного стану та напружень в пуансоні для зворотнього видавлювання корпусів спеціальних накидних гайок. На підставі результатів моделювання із застосуванням пакету програм DEFORM v.10 та результатів експериментального визначення навантажень на пуансони запропонована система плинного моніторингу довговічності інструменту. In the article results over of design of the temperature state and stresses of puncheon are brought for the reverse squeezing out of corps of heads of special nuts. On the basis of results of design with the use of package of softwares of DEFORM v.10 and data of experimental determination of loading on puncheons the system of the current monitoring of longevity of instrument is offered.Item type:Item, Експериментальні дослідження динаміки процесу екскавації сапропелів грейфером(КНТУ, 2011) Ілюшик, І. М.; Ilyushik, I.У статті розроблено методику дослідження динаміки процесу екскавації сапропелів грейфером, що передбачає застосування універсальної вимірювальної системи. There is a dynamics study method of the sapropel grab excavation process that involves the application of universal measuring system developed in the article.