Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
6 results
Search Results
Item type:Item, Експериментальне дослідження універсальної будівельної вібромашини широкого застосування(ЦНТУ, 2022) Яцун, В. В.; Яцун, В. В.; Данілов, В. Ю.; Yatsun, V.; Yatsun, V.; Danilov, V.В роботі проведені експериментальні дослідження працездатності способу збудження резонансних вібрацій пасивними автобалансирами для одномасної вібромашини з поступальним прямолінійним рухом віброплатформи. В результаті експериментальних досліджень встановлено, що у порівнянні зі звичайною інерційною вібромашиною нова машина має на 15-25% більшу продуктивність при меншому на 10-40% споживанні енергії. При цьому дебалансні маси у новому віброзбуднику менші у 4-6 разів дебалансних мас у звичайному інерційному віброзбуднику. Experimental studies of the efficiency of the method of excitation of resonant vibrations by passive autobalancers for a single-mass vibrating machine with translational rectilinear motion of the vibrating platform have been carried out. A vibrating machine with a platform size of 1000x600 mm has been designed, in which a ball balancer is used as a vibrating exciter. The vibrating machine can work in 2 two modes: the first - a vibrating sieve; the second is a vibrating table. The difference between the modes is the different amplitudes and frequencies of the working surface. According to the technical recommendations, Solidworks CAD created a 3D model of a single-mass vibrating machine with a vibrating exciter in the form of a ball autobalancer using the Cosmos Motion module. After checking the performance of the created 3D model, the optimal parameters were selected and an industrial design of the vibrating machine (an exact copy of the 3D model) was created. Before the experiments, a dynamic balancing of the shaft with the autobalancer assembly without balls in their own supports was performed. After checking the quality of balancing, the straightness of the platform was checked. Balls in the autobalancer were removed. 4 checkpoints were applied to the working surface of the platform. An electric motor with a speed of 25 Hz was started. Then with the help of the device "Beam 4" at each point simultaneously measured the value of vibration velocities. As a result of checking the straightness of the platform, it was found that the difference between the values of measurements at different points does not exceed 25%. This indicates the straightness of the movement of all points of the working surface of the platform and, accordingly, the sieve. An electric motor with a speed of 50 Hz was started. Using a vibrometer "Walcom" WM6360 were measured values of movement of the working surface of the table. Then the selection of the unbalanced mass was performed at which the oscillation range of the platform corresponded to the standard values of industrial vibrating machines. Then the platform was loaded with a load of 25 kg, 55 kg and the experiment was repeated. A series of experiments to determine the main characteristics of the developed design of the vibrating machine in the mode of vibrating table and vibrating screen. The energy efficiency of the proposed design of the vibrator was also tested. Measurements of electric energy consumption at different speeds and with different vibrators are performed. As a result of experimental studies, it was found that compared to a conventional inertial vibrating machine, the new machine has 15-25% higher productivity with 10-40% lower energy consumption. The unbalanced masses in the new vibrator are 4-6 times less than the unbalanced masses in the conventional inertial vibrator.Item type:Item, Моделювання руху двомасового вібраційного живильника на базі гідроімпульсного привода(ЦНТУ, 2018) Іскович - Лотоцький, Р. Д.; Коц, І. В.; Іванчук, Я. В.; Івашко, Є. І.; Искович - Лотоцкий, Р. Д.; Коц, И. В.; Иванчук, Я. В.; Ивашко, Е. И.; Iskovych-Lototskyi, R.; Kots, I.; Ivanchuk, Y.; Ivashko, Y.Розроблена нова оригінальна конструкція двомасового вібраційного живильника на базі гідроімпульсного привода, яка врівноважує надлишкові динамічні навантаження. Проведено теоретичне дослідження двомасового вібраційного живильника з гідроімпульсним приводом на базі розробленої математичної моделі. У процесі дослідження була розроблена розрахункова схема пристрою та отримані основі математичні залежності які характеризують режими його роботи та взаємозв’язок робочих параметрів, а також дають змогу оцінити актуальність та перспективність оригінальної розробки. Разработана новая оригинальная конструкция двухмассового вибрационного питателя на базе гидроимпульсного привода, которая уравновешивает избыточные динамические нагрузки. Проведено теоретическое исследование двухмассового вибрационного питателя с гидроимпульсным приводом на базе разработанной математической модели. В процессе исследования была разработана расчетная схема устройства и получены основные математические зависимости, что характеризуют режимы его работы и взаимосвязь рабочих параметров, а также дают возможность оценить актуальность и перспективность оригинальной разработки. The main disadvantage of powerful vibrating feeders with different types of drives, performed on a single-mass scheme, are high dynamic loads on the elements of load-bearing structures. The aim of the article is to develop a mathematical model of the motion of a two-mass vibrating feeder based on a hydroimpulse drive, to confirm the feasibility of developing and its performance in the future. Vibrating feeders with a hydropulse drive are tuned to near resonance mode, as a result of which the dynamic load on the foundation can reach very high values. The solution to this problem is to establish an additional reactive mass, which will absorb the excessive dynamic loads. A new original design of a two-mass vibrating feeder based on a hydropulse drive is developed, which balances the excess dynamic loads. A mathematical model of the motion of a two-mass vibrating feeder is developed, which is represented by a system of Lagrange differential equations. The solution of the mathematical model of motion of a vibrating feeder was carried out by the method of introducing a complex variable. A theoretical investigation of a two-mass vibrating feeder with a hydroimpulse drive based on the developed mathematical model is carried out. In the process of research, the design scheme of the device was developed and the mathematical dependences obtained on the basis of a system of differential equations were derived. A mathematical model of the motion of a vibrating feeder has been developed which allows to optimize the parameters of debugging of the hydroimpulse drive and to outline ways to solve the problem of extremely high dynamic loads on the foundation while developing new original designs of two-mass vibrating feeders. Solving the system of differential equations that characterize the modes of its operation and the interrelationship of operating parameters make it possible to assess the relevance and prospects of the original development.Item type:Item, Теоретичне обґрунтування параметрів вібраційного висіву(КНТУ, 2016) Мартиненко, С. А.; Ауліна, Т. М.; Артеменко, Д. Ю.; Martinenko, Sergiy; Aulina, Tetyana; Artemenko, DmitryВ статті розглянуто типи висівних апаратів зернових сівалок. Проаналізовано їх переваги та вади. Запропоновано конструкцію вібраційного висівного апарату та методику первинних розрахунків його основних параметрів – частоти та напряму коливань. Побудовано графік визначення режиму роботи апарату в залежності від цих параметрів. Using of vibrations for the ordinary sowing of seed to this time not used in practice, although simplicity of construction as compared to the pneumatic sowing is obvious. In the article the new construction of oscillation seedmeter is offered and the theoretical calculations of basic his office hours are conducted. Worked out differential equations, describing motion of seed in the process of oscillation motion. On the basis of agrotechnical requirements the parameters of work are expected, namely, frequencies and directions of vibrations, providing the set process of portage of seed. The analysis of different terms of work of vehicle is conducted. As a result was certainly following. On the basis of the conducted theoretical researches certainly parameters and modes of operations of the offered vehicle. The chart of dependence of the mode of operations of sowing oscillation vehicle from correlation of frequency of vibrations of tray and corner of vibration and given recommendations is made in relation to subsequent researches.Item type:Item, Експериментальне дослідження впливу вібрації на ефективність процесу скальперування зернового вороху(КНТУ, 2013) Тіщенко, Л. М.; Богданович, С. А.; Tischenko, Leonid; Bogdanovich, SergeyНаведені результати експериментального дослідження технологічного процесу сепарування зернового вороху барабанним скальператором при обертальному русі решета і при накладенні вібрації. The objective is to perform analysis and comparative study of the effectiveness of a cylindrical sieve when it only rotational movement and with the addition of vibration. The results of experimental investigation of the technological process of separation of grain heap on the horizontal drum separator for the separation of large impurities when only the rotational motion of his sieve and when applied to this movement vibration. Imposition of vibration significantly improve specific productivity of separator. The optimum mode of vibration. Conclusions 1. Adding vibration to rotational motion of a cylindrical sieve drum skalperators can increase its share performance without sacrificing quality of the process skalperuvannya. The optimum value of vibration intensity is (1.2 ... 2) g. 2. Vertical vibrations are more favorable to the quality of the skalperuvannya than the horizontal axis.Item type:Item, Побудова математичної моделі коливального руху у ґрунті зубчастого сошника селекційної сівалки(КНТУ, 2015) Булгаков, В. М.; Головач, І. В.; Горобей, В. П.; Свірень, М. О.; Bulgakov, Vladimir; Golovach, Ivan; Gorobey, Vasiliy; Sviren, MikolaДля розробленої нової конструкції комбінованого сошникового вузла створена теорія руху у ґрунті зубчастого розрізаючого диска сошника селекційної сівалки, встановленого на вібраційній підвісці. Складені диференціальні рівняння горизонтальних і вертикальних поступальних коливань лонжерона комбінованого сошникового вузла з зубчастим розрізаючим диском і системою пружинних механізмів з натискною пружиною і пружиною вібратора для вивчення впливу віброефекту на тяговий опір сошника. Отримана математична модель дала змогу визначати амплітуди і частоти поступальних коливань лонжерона комбінованого сошникового вузла в залежності від конструкційних параметрів і кінематичних режимів роботи з метою визначення їх впливу на технологічний процес, що дозволить оцінити стан системи і оптимізувати енергетичні характеристики універсальної сівалки. Research invention is extend of technological possibilities of selection-seed-growing seeder, increasing(rising) of reliability of sowing technological process by diminish of energoexpenditure at the expense of using vibration interaction effect of working organ with soil by definition of rational construction parameters and kinematic regimes of aggregate work. For developed construction of universal ploughshare unit with working organs, which mounted on vibration hanger and with complation in dependence from technology choice and for selection-seed-growing seeder it is developed theory of movement in soil of tooth cutting ploughshare disk. It is developed mathematical model of vibration movement in soil, put together with differential equations of horizontal and vertical progressive vibration movements of longeron of universal ploughshare unit with tooth cutting disk and system of spring mechanisms with pressing spring, a vibrator spring fordefinition of umplitude and frequency progressive aggregate vibration, studing and optimization construction parameters and kinematics regimes of aggregate work. According to mathematical model put together with soil of universal ploughshare unit with tooth cutting disk and system of spring mechanisms it is developed calculations with the help of program MathCAD, it is constructed amplitude-frequency characteristics of ploughshare unit for further estimation of system state, energetic control, optimization of construction parameters and kinematic regimes of aggregate work.Item type:Item, Дослідження мікропрофіля поверхні одержаного вібраційною обробкою фрезами малого діаметра(КНТУ, 2015) Струтинський, В. Б.; Перфілов, І. В.; Strutynsky, Vasil; Perfilov, IvanВикладено результати досліджень мікропрофіля поверхні одержаного фрезерувальною обробкою фрезами малого діаметра на спеціально розробленому обладнанні. Показано, що мікропрофіль включає ділянки з ізольованими екстремумами та ділянки квазіперіодичності із чітко визначеним напрямком мікрорисок. Запропоновано опис мікропрофіля аналітичними залежностями. Для ділянки з ізольованими екстремумами опис мікропрофіля проводиться функціями на основі кривих Гауса. Для ділянок квазіперіодичності рекомендований спектральний аналіз мікропрофіля шляхом подання його у вигляді відрізка ряду Фур’є. Виконано аналіз особливостей мікропрофіля по різним ділянкам. The results of surface microprofile research obtained with the milling cutters of small diameter on a specially designed equipment are presented. It is shown that the microprofile includes the areas with isolated extremes and the areas of quasiperiodicity with a clear focus of microstrips. A microprofile description with analytical dependencies are suggested. For the areas with isolated extremes the description of microprofile functions is carried out based on the Gaussian curves. For areas with quasiperiodicity the spectral analysis of microprofile by submitting it as a segment of a Fourier series is recommended. The analysis of microprofile in different areas is made. The research purpose is to develop methods for assessing the quality parameters of obtained microprofile which was processed with small diameter mills with imposing high vibration on the workpiece. The special equipment for forming the microprofile was developed. Methods for estimating the microprofile parameters in areas with isolated extremes and in areas with quasi-periodic statements and valves were suggested. The analytical description of microprofile with the set of Gaussian curves and segments of Fourier rows based on microprofile spectrum analysis. The microprofile features analysis was made. The conclusion about the microprofile quality parameters obtained with vibration processing with small diameter mills and the methods of this type of microprofile analysis.