Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
6 results
Search Results
Item type:Item, Технологічне проєктування способів виготовлення U-подібних гвинтових поверхонь транспортних труб(ЦНТУ, 2025) Гевко, І. Б.; Рогатинський Р. М.; Комар, Р. В.; Ткаченко, І. Г.; Гупка, А. Б.; Нevko, І.; Rohatynskyi, R.; Komar, R.; Tkachenko, I.; Gypka, A.В роботі обґрунтовано чотири нові способи виготовлення U-подібних гвинтових поверхонь транспортних труб з використання оправ і формувальних роликів. Розроблені способи можуть реалізовуватися різними шляхами. Зокрема вминанням U-подібних рифів на готовій трубі, або одночасним навиванням та U-подібним вминанням стрічки прямокутного січення на оправу з Uподібним спіральним виступом, з подальшим скріпленням виступів навитої стрічки зварним швом. Загалом розроблені способи виготовлення U-подібних гвинтових поверхонь транспортних труб можна умовно поділити на два типи - із можливістю зміни висоти U-подібного рифу за рахунок зміни діаметр прутка пружини, та без такої можливості, в яких використовуються оправи з незмінною висотою Uподібного рифу. Також в роботі визначено і охарактеризовано конструкційні матеріалами для виготовлення гвинтових транспортних труб. У якості вихідних заготовок доцільно використовувати труби безшовні холодно- і гарачекатані, труби литі, смуговий холоднокатаний прокат. Для обох типів способів визначено і представлено раціональні конструктивно-технологічні параметри їхної реалізації. The process of technological design and manufacturing of special screw blanks is accompanied by a number of technical and production problems that require systematic analysis and comprehensive solutions. One of the main problems is the difficulty of ensuring high accuracy of the geometric parameters of screw surfaces, especially in conditions of single or small-scale production. Such surfaces have a complex spatial shape, which requires the use of specialized tools, high-precision equipment and modern control methods. Another important challenge is the choice of the optimal method of forming the workpiece depending on the material, design requirements and operating conditions. In this case, it is necessary to take into account not only technical characteristics, but also the economic feasibility of production, equipment costs, and energy intensity of the process. Another problem is achieving the required mechanical properties of the product (strength, wear resistance, fatigue endurance), which often requires the implementation of additional technological operations, in particular heat treatment or surface hardening. All these factors complicate technological planning, increase the risks of defects and increase the cost of production. Thus, the main problem is to develop rational and technically efficient technological methods that are capable of ensuring the manufacture of special screw blanks with the required characteristics at minimal production costs.Item type:Item, Аналіз науково-технічних інновацій в галузі машинобудування з виявленням закономірності впливу технологічних параметрів(ЦНТУ, 2023) Гайкова, Т. В.; Ковальчук, Д. М.; Гайков, Р. М.; Haikova, T.; Kovalchuk, D.; Haikov, R.У статті розглянуто виявлення закономірності впливу технологічних параметрів на неоднорідність інтенсивності деформації та опору матеріалу пластичному деформуванню у стінці деталі при витяжці прямокутних деталей із біметалів. При розробці технологічного процесу отримання виробів з шаруватих металів з попереднім зчепленням шарів необхідно враховувати пошарові деформації, їх залежності від параметрів процесів формозміни, їх механічні властивості, а також вплив термомеханічних параметрів обробки на міцність з’єднання складових. Based on the analysis of scientific and technical information, it established that today layered metals are one of the most modern and promising materials used in all branches of mechanical engineering and national economy. The use of bimetals allows you to achieve significant cost savings, obtain materials with unique properties, increase production efficiency and competitiveness of a wide class of parts and equipment. The purpose of the article is to analyze the methods of determining the stress state of a workpiece with heterogeneous mechanical characteristics in the process of plastic deformation and to determine the stress-strain state when drawing rectangular parts from bimetals. As a result, of unequal deformation conditions in different parts of the contour, as well as anisotropy of the mechanical properties of the workpiece material, the height of box-shaped parts is even more uneven than the height of axisymmetric parts obtained by drawing. Therefore, in the manufacturing process of such parts, cutting of the uneven edge provided. The trimming allowance depends on the relative height of the part. The bigger it is, the bigger the allowance. Since the flange naturally thickens during drawing in the corner sections of the part contour, this phenomenon taken into account when determining the gap between the punch and the die of the drawing die: in the corner sections, the gap should be greater than in the straight sections of the die contour. Extrusion of box-shaped parts from bimetals causes even greater unevenness of deformations. A different amount of deformation of the layers of the bimetallic work piece imposed on the general sign change of the voltages, which causes bending and warping of the rectilinear parts of the semi-finished product, and therefore, the impossibility of obtaining a high-quality product. Based on the analysis of the stress-strain state of the workpiece in the process of drawing bimetal. The following provisions are proposed: if the mechanical properties of the metal layers do not differ - the two-layer metal behaves like a single-layer, then the ratio of the thicknesses of the two-layer metal does not change after drawing; if the mechanical properties of the layers differ, then the ratio of the thicknesses of the two-layer metal changes after drawing. Thus, when the ratio σs1/σs2 decreases, the thickness of the first layer, which has lower mechanical properties, decreases at the output; the thickness ratio after drawing also depends on the initial ratio of metal thicknesses. Based on the analysis of the stress-strain state of the work piece during the extraction of box parts, the following methods and techniques have been determined for obtaining high-quality parts by extraction and saving material: use metals with similar mechanical properties; the desire to increase the curvature of the corner zones of the work piece; to calculate the dimensions of the work piece for the hood with the involvement of modern mathematical apparatus (potential method); use brake media instead of brake ribs; affect the center of deformation, increasing the effect of unloading tangential stresses.Item type:Item, Влияние схемы напряженно-деформировочного состояния на локализацию деформаций, предшествующую разрушению(КНТУ, 2009) Мороз, Н. Н.; Драгобецкий, В. В.; Бойко, Ю. А.; Мороз, Н.; Драгобецький, В.; Бойко, Ю.; Moroz, N.; Dragobetskiy, V.; Boiko, U.Установлена зависимость между параметрами, характеризующими схему напряженно- деформировочного состояния с предельной деформацией материала заготовки. На основании проведенных теоретических исследований авторами получено замкнутое эксперементалыю- аналитическое решение уравнения связи интенсивности деформаций с отношением главных напряжений, позволяющее выявить предельно-допустимые степени формоизменения без локализации деформаций. Встановлена залежність між параметрами, що характеризують схему напружено- деформаційного стану з граничною деформацією матеріала заготовки. На онові проведених теоретичних досліджень авторами одержано замкнуте експериментально-аналітичне рішення рівняння зв’язку інтенсивності деформацій з відношенням головних напруг, що дозволяють виявити гранично-допустимі ступені формозміни без локалізації деформації. Determined the dependence between parameters that are characterizing the scheme of strained- deformation mill with limiting deformation of material procurement. On the base of conducted theoretical researches by the authors were received closed experimentally-analytical resolution leveling of connection link power of deformation concerning the main strain that allowing to show limiting permissible degrees of hanging forms without localization of deformation.Item type:Item, Розмірна обробка електричною дугою складних за зовнішнім контуром деталей(КНТУ, 2015) Носуленко, В. І.; Юр’єв, В. В.; Nosulenko, Viktor; Yuriev, VitalyОписано технологічну схему формоутворення розмірної обробки електричною дугою складних за зовнішнім контуром деталей та запропоновано конструкцію електрода-інструмента, що дозволяє визначити запропонований спосіб, як високоефективну альтернативу традиційним технологіям. Purpose – to increase the technological capabilities of the process dimensional processing electric arc of difficult at the external contour of the parts. The work presents the described method and the electrode-tool for machining complex at the external contour of the parts in the implementation of the technological scheme of formation by direct pumping of the working fluid. The results of experimental research of the technological characteristics of the process of dimensional processing electric arc such as: the processing performance M mm3 /min, the roughness of the processed surface Ra μm, the relative linear wear of the electrode tool of Ȗ % and the side electrode gap į mm. Dimensional processing electric arc is the most effective of the known methods of processing complex at the external contour of parts and implements technological scheme of formation by direct pumping of the working fluid through the electrode-tool geometry of the working edge of which is built on the following parameters: inlet electrode gap provide uniform within the working fluid in the gap due to the inclination of the inner wall of the electrode tool within the Į – 0,5...1°, and from it on the working end surface provide a work belt (equation) within 3...5 mm. In addition to the working zone in the circumferential direction of the electrode-tool include the inclination ȕ - 3...5° that the steady flow of the working fluid in the electrode gap and the corresponding quality of the processed surface.Item type:Item, Розмірна обробка електричною дугою отворів складного контуру(КНТУ, 2015) Носуленко, В. І.; Юр’єв, В. В.; Nosulenko, Viktor; Yuriev, VitalyРозроблено, теоретично та експериментально досліджено і описано технологічні схеми формоутворення розмірної обробки електричної дуги (РОД) листових деталей складного контуру згідно класифікатора та фізико-технологічні характеристики процесу, його гідродинаміка, конструкції електрода-інструмента (ЕІ), як високоефективну альтернативу традиційним технологіям. The article is devoted to the development and improvement in dimensional processing electric arc holes of challenging when pumping circuit through the electrode-tool and the workpiece. In work the analysis of the known methods of processing of complex contour holes and their shortcomings. Substantiated the technological scheme of forming holes of complex contour method dimensional processing electric arc. Were developed the structure of the electrodes and their relative linear wear A method dimensional processing electric arc for processing sheet metal parts of complex contour and electrode-tool, ensuring high quality treatment.Item type:Item, Анализ распределения напряжений при радиально-ротационном профилировании ободьев колес(КНТУ, 2015) Пузырь, Р. Г.; Пузир, Р. Г.; Puzyr, RuslanВопросы определения поля напряжений при формоизменении ободьев колес из стальных заготовок на первом переходе радиально-ротационного профилирования являются актуальными. Интерес представляет определение напряжений на радиусе закругления профилирующего ролика, так как именно места сопряжений различных элементов профиля обода испытывают во время эксплуатации наибольшие нагрузки. Результаты теоретического исследования позволяют анализировать возникающие в процессе деформирования напряжения и определять совокупность технологических и конструкторских параметров процесса профилирования, которые оказывают значительное влияние на величину и распределение нормальных и касательных напряжений. Питання визначення поля напружень при формозміні ободів коліс із сталевих заготовок на першому переході радіально-ротаційного профілювання є актуальними. Інтерес представляє визначення напружень на радіусі закруглення профілюючого ролика, так як саме місця сполучень різних елементів профілю обода відчувають під час експлуатації найбільші навантаження. Результати теоретичного дослідження дозволяють аналізувати виникаючі в процесі деформування напруження і визначати сукупність технологічних і конструкторських параметрів процесу профілювання, які роблять значний вплив на величину і розподіл нормальних і дотичних напружень. The problems of determining the stress field at forming rim of steel billets at the first transition angular rotational profiling. Interest is the determination of the stresses on the radius of curvature of the profiling roller, as it places the coupling of different elements of the rim profile test during operation to maximum loads. The results of theoretical studies allow to analyze the deformation occurring during stress and to determine a set of technological and design parameters of the profiling process, which have a significant influence on the magnitude and distribution of normal and tangential stresses. Obtained according to different view of the blank deformation of the wheel rim as the design and not the sheet metal that can reveal an increasing amount of the profiling process, and keep a more accurate calculation of stresses and strains. It is shown that the radii of curvature of the wheel profile during the tensile deformation occur meridional stress that can lead to a dramatic thinning the blank that are not acceptable.