Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Можливість модернізації механічної обробки багатоступінчастих валів на токарних верстатах застарілої конструкції(КНТУ, 2013) Анастасенко, С. Н.; Григурко, І. О.; Капура, І. А.; Anastasenko, Sergey; Grigyrko, Ivan; Kapyra, ІgorПредставлена модернізація токарних верстатів застарілої конструкції з реконструкцією гідрокопіювальних супортів для обробки багатоступінчастих валів та улаштування для автоматизованого завантаження, закріплення і зняття заготовок. При конструкторській розробці на заводі можливо враховувати виробничі можливості ремонтних і інструментальних цехів, на котрі покладається задача переобладнання верстатів і ретельного розрахунку економічних показів, які визначають рентабельність реконструкції і степені автоматизації. В більшості випадків при автоматизації верстатів для роботи за замкнутим циклом виготовлення простих деталей можемо рекомендувати пневмомеханічні улаштування, комбінуючи механічний барабанний привід супорту з пневматичними затискними улаштуваннями. It is presented the putmoded turn bench with reengineering of hydro-copying carrage for multiplediameters part processing and computerized work pieces loading, fixture and relieving devices. At designer development at the plant it is possible to take into account production mo-zhlivosti of repair and instrumental workshops upon which the task of re-equipment of machine-tools and careful calculation of economic pokazkiv, yaki depends determine profitability of reconstruction and degrees of automation. In most cases during automation of machine-tools for work after the reserved cycle of vigotov-lennya of simple details can recommend the pneumomassage arranging, combining a mechanical drum occasion support from.Item Модернізація вузлів обладнання для механічної обробки гільзи циліндрів двигуна на токарних верстатах застарілої конструкці(КНТУ, 2015) Анастасенко, С. М.; Григурко, І. О.; Ошовський, В. Я.; Будуров, В. Л.; Anastasenko, Sergey; Grigyrko, Ivan; Ohsovsrsy, Victor; Bydyrov, VasilyУ статті представлена модернізація токарних верстатів застарілої конструкції з реконструкцією гідрокопіювальних супортів для механічної обробки гільзи циліндра двигуна та улаштування для автоматизованого завантаження, закріплення і зняття заготовок. При конструкторській розробці на заводі можливо враховувати виробничі можливості ремонтних і інструментальних цехів, на котрі покладається задача переобладнання верстатів і ретельного розрахунку економічних показників,які визначають рентабельність реконструкції і степені автоматизації. В більшості випадків при автоматизації верстатів для роботи за замкнутим циклом виготовлення простих деталей можемо рекомендувати пневмомеханічні улаштування, комбінуючи механічний барабанний привід супорту з пневматичними затискними улаштуваннями. In article modernization of lathes of an outdated design with reconstruction of hydrocopy calipers is provided for machining of a cylinder liner of the engine and the device for the automated loading, fastening and removal of preparations. At design development at plant it is possible to consider production capabilities of maintenance and tool shops to which the problem of re-equipment of machines and careful calculation of economic indicators which define profitability of reconstruction and extent of automation is assigned. In many cases at automation of machines for work behind the closed cycle production of simple details is recommended the pneumomechanical devices combining a mechanical drum drive gear of a caliper with air clamping devices. Re-equipment of the machine is reduced to installation of tightening cylinders, to production of mandrels and the rotating spindle of the rear grandma. Cylinders and cranes of steering and shops. Lathe productivity with a hydrocopy caliper and loading organization will increase by 10 times equalizing it with a productivity at manual service, and expenses will pay off approximately in three months.