Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
15 results
Search Results
Item Проблема надійності водопровідних мереж на прикладі міста Кропивницького(ЦНТУ, 2021) Клименко, В. В.; Ковальчук, Н. В.; Гуцул, В. І.; Телюта, Р. В.; Klymenko, V.; Kovalchuk, N.; Hutsul, V.; Teliuta, R.В статті проаналізовано причини аварій та витоків на водопровідних трубах розподільчої мережі м. Кропивницького та обраховано статистичні дані експлуатаційної організації по аварійним ситуаціям при експлуатації трубопроводів діаметром від 25 до 1100 мм протягом останніх п’яти років. Встановлено, що основними видами пошкоджень труб водопровідної мережі є : наскрізні свищі сталевих труб – 54,4%; корозія сталевих труб – 25,6%; розчеканка стиків чавунних труб – 9,7%, переломи та тріщини чавунних труб – 6,1%; тріщини на стиках пластикових труб та інші – 4,2%. Отримано аналітичні залежності середнього значення параметра потоку відмов трубопроводу ω0ср від діаметра труб D та підтверджено тенденцію зменшення ω0ср при збільшенні D. Рекомендовано для підвищення надійності водопровідних мереж проводити заміну 2% мережі на рік та використовувати пластикові труби. Для зменшення ω0ср, зокрема на ділянках труб з понаднормовим терміном експлуатації, показана доцільність установлення парціально безпосередньо в трубопровід водоповітряних гасників коливань тиску, в яких відбувається поступове і повне гасіння ударної хвилі. The article presents the analysis of statistical data of the causes of breakages and leaks in water pipes of the distribution network of Kropyvnytskyi. Breakage statistics for pipelines with a diameter of 25 to 1100 mm during the last five years were calculated. As a result of segmental analysis, it was found that the main types of damage to the pipes of water supply system are through fistulas of steel pipes – 54.4% and corrosion – 25.6%; loss of integrity of cast iron pipes on joints – 9.7%, fractures and cracks of cast iron pipes – 6.1%; fractures in joints of polyethylene pipes and other damages – 4.2%. To characterize the reliability of the municipal water supply networks, the pipeline failure flow parameter ω was used. It was defined as the ratio of the number of failures of the water supply network section to the observation period and the length of pipe network sections of the corresponding diameter. The calculation of interval estimates for the failure rate parameter ωо for steel and cast iron pipes of the water distribution network of Kropyvnytskyi was carried out. According to the operational organization 84% of the network was laid using these pipes and analytical expressions were obtained to determine average values of ω0ср depending on their diameter. Significantly higher values of ω0ср were noted in comparison with similar ones given in the literature for other cities, which can be explained by a significant excess of the standard service life of 85% of steel and 50% of cast iron pipes in the water supply network of Kropyvnytskyi. To increase the reliability of water supply networks, it is recommended to implement the experience of European countries and replace 2% of the network per year and use polyethylene pipes. To reduce the failure factor of water supply networks, particularly in those areas where overtime pipes are used, the expediency of partial installation of water-air dampers for pressure fluctuations directly in the pipeline, in which there is a gradual and complete damping of the shock wave. Approbation of a prototype of a hydraulic shock absorber of this design was carried out in the hydraulics laboratory at Central Ukrainian National Technical University and its efficiency and high efficiency at full shock wave damping was confirmed.Item Теоретичне дослідження руху сипкого матеріалу в постачальному пристрої установок безперервної дії(ЦНТУ, 2019) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Орышака, О. В.; Гуцул, В. И.; Артюхов, А. Н.; Oryshaka, O.; Gutsul, V.; Artiuhov, A.Отримані залежності швидкості руху сипкого матеріалу в постачальному пристрої установок безперервної дії від геометричних параметрів постачального пристрою, а також визначено діапазон зміни швидкості руху сипкого матеріалу в постачальному пристрої. Полученны зависимости скорости истечения сыпучего материала в подающем устройстве установок непрерывного действия от геометрических параметров питающего устройства, а также определён диапазон изменения скорости истечения сыпучего материала в подающем устройстве. Continuous-action plants have several advantages over cycle-feed units (low energy costs, high productivity, lower material consumption, etc.), so improving continuous-action installations is an urgent task. The bulk material feeder, as an integral part of the continuous-action plants, requires appropriate research to substantiate and optimize the design parameters of the installation. The purpose of this work is to investigate the influence of the geometrical parameters of the stabilizing slope of the delivery devices of the continuous-action installations for loading free-flowing materials on the speed of movement of the bulk material and, thus, the technological process of the installation for loading bulk materials. The dependences of the velocity of the free-flowing material in the delivery device of the continuous devices on the geometric parameters of the supply device are determined, as well as the range of velocity variation of the bulk material movement in the feed device is determined. Research findings. The velocity of loose material increases with increasing radius r (fig. 3) and angle (fig. 2). The range of variation in speed (variability, boundary limits) of the velocity of free-flowing material in the supplying device is determined. At , the velocity of the free-flowing material varies between 2,11 ... 2,3 m / s. The obtained results allow to determine the values of the main geometric parameters of the supply device of the continuous devices to provide the required output indicators The results obtained allow us to determine the values of the basic geometric parameters of the stabilizing slope of the delivery devices of the continuous operation installations to provide the required output indicators.Item Теоретичне дослідження регулятора витоку сипкого матеріалу(ЦНТУ, 2017) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryshaka, O.; Gutsul, V.; Artiuhov, A.Отримані залежності впливу кута нахилу поверхні конусного ската регулятора витоку сипкого матеріалу та радіуса округлення торцевої частини полого циліндра регулятора витоку сипкого матеріалу на максимальне значення переміщення конусного ската, при якому площа витоку сипкого матеріалу залишається меншою за площу вхідного отвору матеріалопровода; залежності впливу значення переміщення конуса на час повного вивантажування бункера; залежності, які дозволяють визначати швидкість витоку матеріалу та об'єм вивантаженого матеріалу при різних значеннях основних параметрів регулятора. The dependences of the influence of the angle of slope of the cone-slope surface of the regulator of the outflow of loose material and the radius of rounding of the end part of the hollow cylinder of the flow-out material flow controller on the maximum value of the cone-shaped slope movement, at which the flow area of the loose material remains less than the area of the inlet of the material duct; Dependence of influence of value of cone displacement on the time of complete unloading of the hopper; Dependencies that allow to determine the flow rate of.Item Теоретичне дослідження конусного стабілізатора потоку сипкого матеріалу установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2016) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryshaka, О.; Gutsul, V.; Artiuhov, А.Отримані залежності швидкості руху сипкого матеріалу по конусному стабілізатору залежно від величини кута конуса, відстані від конусного стабілізатора до заслінки клапана і коефіцієнта тертя сипкого матеріалу, зазору між торцем матеріалопровода і конусним стабілізатором, товщини шару сипкого матеріалу, що сходить з поверхні конуса. The resulting dependence of the speed of the free-flowing material in the feed device from the height of the free flight, the coefficient of friction, angle of inclination of the side walls of the receiving receiving hopper, as for the case of fixed position receiving hopper, and for the case of circular motion of the funnel for different values of the angular velocity. When you increase the angle of the surface of the cone to the horizontal and V0 the speed of descent of granular material from the cone increases, and the thickness of the layer of bulk material flow that is coming off the cone decreases. A significant impact on the speed of descent of granular material from the cone and the thickness of the layer of bulk material flow that is coming off the cone f has. For large values of the coefficient of friction of the granular material on the surface of the cone, the surface of the cone to cover the materials with small values of the coefficient of friction.Item Оцінка значень коефіцієнта Джині при деяких законах розподілу сукупного доходу(КНТУ, 2011) Гуцул, В. І.; Кадашова, В. О.В статті досліджується нерівномірність доходів населення за допомогою коефіцієнта Джині k. Аналізується залежність коефіцієнта Джині k від закону розподілу доходів населення та співвідношення мінімального і максимального розмірів доходів. Отримані результати представлені в аналітичній та графічній формах.Item Аналіз постачальних пристроїв установок безперервної дії для завантаження сипких матеріалів з одним блоком завантажувальних секцій(КНТУ, 2016) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryhsaka, Oleg; Gutsul, Vasily; Artiuhov, AnatolyОтримані залежності швидкості сипкого матеріалу в постачальному пристрої від висоти вільного падіння, коефіцієнта тертя, кута нахилу бокових стінок приймальної воронки, як для випадку нерухомого положення приймальної воронки, так і для випадку обертального руху воронки при різних значеннях кутової швидкості. Devices of continuous action have a number of advantages over systems with cyclic flow (high performance, low energy costs, lower consumption of materials and other). Improvement of continuous action is an actual scientific problem (is an urgent task). Аn analysis was Conducted of the influence of parameters of feeding mechanism of device on the speed of the free-flowing material. The resulting dependence of the speed of the free-flowing material in the feed device from the height of the free flight, the coefficient of friction, angle of inclination of the side walls of the receiving receiving hopper, as for the case of fixed position receiving hopper, and for the case of circular motion of the funnel for different values of the angular velocity. Conclusions: 1. At a stationary position of the funnel ensures a safe movement of the bulk material. 2. When a reciprocating rotary motion around the axis of the funnel can be a risk disturbing the process. To ensure reliable movement of bulk material is necessary to limit the angular rotation speed, or decrease the frictional force by applying materials with low friction for the respective surfaces.Item Обґрунтування геометричних параметрів дискового очисника лап парових культиваторів(КНТУ, 2009) Васильковський, О. М.; Гуцул, В. І.; Савченко, Д. С.; Vasil'kovskiy, А.; Guzul, V.; Savchenko, D.Стаття присвячена теоретичним дослідженням дискового очисника стояків лап парових культиваторів. В статті представлено результати аналізу роботи класичного вирізного диску на основі яких запропоновано підвищити ефективність роботи дискового очисника встановленням захоплювальних пальців. Крім того, описані основні геометричні параметри запропонованого очисника та розглянуто умови захвату стебел захоплювальними пальцями. Наведено оцінку кута защемлення між робочими органами очисника у момент дотику до стебла. The article is devoted theoretical research of disk purifier of chimneys of paws of steam cultivators. In the article the results of analysis of work are presented classic carved a disk on the basis of which it is suggested to promote efficiency of work of disk purifier establishment of fascinating fingers. In addition, the basic geometrical parameters of the offered purifier are described and the terms of delight of stems are considered by fingers. The estimation of corner of jamming between the workings organs of purifier is resulted in the moment of touch to the stem.Item Вплив аеродинамічної сили на умови статичного зрівноваження автобалансирами крильчатки осьового вентилятора(КНТУ, 2008) Філімоніхін, Г. Б.; Гуцул, В. І.Досліджується вплив аеродинамічної сили на умови статичного зрівноваження автобалансирами крильчатки осьового вентилятора. Досліджується просторовий рух ротора. Отримані диференціальні рівняння просторового руху ротора, на якому закріплені лопасті. Із застосуванням інженерного (емпіричного) критерію настання автобалансування визначаються діапазони швидкостей, на яких можливе автобалансування ротора. Autobalancer influence of aerodynamic force on the statistic counterbalancing wings of the axle fan is researched. There researched a special motion of the rotor. Differential equations of the special motion of the rotor wings are obtained. By means of engineering (empirical) criterion of autobalancing at which autobalansing begins you can determine the speed ranges which make rotary autobalansing possible.Item Визначення величини робочого об'єму героторних гідромашин з епіциклоїдальною цівковою передачею внутрішнього зачеплення(КНТУ, 2012) Скібінський, О. І.; Гуцул, В. І.; Гнатюк, А. А.; Заярна, А. В.; Skibinskiy, O.; Gutsul, V.; Gnatuk, A.; Zayarna, A.В статті описана методика розрахунку робочого об’єму героторних гідравлічних машин з епіциклоїдальними цівковими передачами внутрішнього зачеплення. In this paper to describe method of job volume of hydraulic machines with center epicyclic transmission internal gear.Item Обгрунтування постачального пристрою установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2014) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryhsaka, O.; Gutsul, V.; Artiukhov, А.Визначений вплив параметрів постачального пристрою на швидкість руху сипкого матеріалу в каналах патрубків в стаціонарному положенні і при обертанні пристрою, зміна лінійної питомої маси сипкого матеріалу в патрубках, а також центр мас сипкого матеріалу. Установлено, що швидкість руху сипкого матеріалу в каналах патрубків при обертанні пристрою збільшується відносно його стаціонарного положення, що виключає порушення технологічного процесу із-за забивання каналів патрубків. Modern machines for loading friable materials into valve bags require a considerable amount of energy, allow the loss of fasoo material, as well as the violation of technological process at boot friable materials, so the improvement of modern mechanization is an actual scientific problem. The effect of the parameters of the feeding device the speed of movement of the friable material in the channels of the nozzle in a stationary position during rotation of the device, the change of a specific linear mass of granular material in the channel setup. It is established that the speed of the friable material in the channels of the nozzles during rotation of the device increases relative to its stationary position, which eliminates the violation of technological process of plugging nozzles. Resume: 1. The speed of movement of the friable material in patrols postchallenge of the device increases when the rotation of the rotor relative to the stationary position of the rotor. This makes it possible to avoid the accumulation of loose material that could lead to blockage of the channel. 2. With increasing angular velocity of rotation of the rotor the flow of material moves from the lower to the upper wall of the socket. 3. The weight of friable material in patrols, when the rotor is reduced.