Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
7 results
Search Results
Item Аналіз теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса(ЦНТУ, 2017) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Красота, М. В.; Руденко, Т. В.; Kuleshkov, Y.; Magonets, E.; Kuleshkova, K.; Krasota, M.; Rudenko, T.В статті наведені результати аналізу теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса. Встановлені теоретичні залежності об’єму відсіченої порожнини від параметрів зубчастого зачеплення, а також від положення точки зачеплення на лінії зачеплення шестерень насоса. Отримані теоретичні залежності дозволяють визначити геометричні параметри відсіченої порожнини, при яких виключається явище компресії робочої рідини. Виключення компресії досягнуто завдяки використанню зубчастого зачеплення з асиметричною лінією зачеплення. В роботі вказані недоліки існуючих теоретичних досліджень і вказані напрямки подальшого їх розвитку.The objective of research is to analyze scientific and technical information on the results of theoretical studies of the geometric parameters of the cut-off housing of the gear pump and to determine future direction of research of the processes that take place in the cut-off housing and to formulate the scientific hypothesis of the research. The article presents the results of the analysis of theoretical studies of geometric parameters of the cut-off housing of the gear pump. The theoretical dependences of the volume of the housing on the parameters of toothing were established as well as the position of the point of engagement on the line of contact of a gear pump. The theoretical dependences allow determining geometrical parameters of the cut-off housing which eliminate the phenomenon of the working fluid compression. The avoidance of compression is achieved through the use of toothing with asymmetrical engagement line. The work indicates the shortcomings of existing theoretical research and presents the directions of further development. It was established that one of the possible ways to reduce the impact of the compression of the working fluid in the cut-ff housing is to use toothing with asymmetric line engagement.Item Аналіз гідродинамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса(КНТУ, 2016) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Руденко, Т. В.; Красота, М. В.; Kuleshkov, Y.; Mahonets, E.; Kuleshkova, K.; Rudenko, T.; Krasota, M.В статті наведені результати аналізу впливу динамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса на його працездатність. Зазначені умови виникнення компресії і декомпресії робочої рідини у відсіченій порожнині шестеренного насоса. Встановлено взаємозв’язок між компресією і декомпресією робочої рідини, що виникають у відсіченій порожнині шестеренного насоса і негативним впливом цих явищ на працездатність насоса. Зазначено зниження працездатності шестеренного насоса внаслідок негативного впливу гідродинамічних явищ у відсіченій порожнині, що виявляється у підвищеному зношуванні деталей і з’єднань насоса, зниженні довговічності, коефіцієнту подачі, підвищенні пульсації тиску і подачі, збільшенні вібрацій і шуму НШ. The objective of the work is to analyse scientific and technical information and to determine further directions of research of processes taking place in the isolated section of a gear pump and to formulate scientific hypothesis of the research. The article presents the analysis results of the influence of dynamic processes taking place in the isolated section of a gear pump on its operational performance. The conditions of the occurrence of compression and decompression of hydraulic oil in the isolated section of a gear pump were determined. The interrelationship between the compression and decompression of the hydraulic oil which occurs in the isolated section of a gear pump and the negative influence of these effects on the operational performance of a pump was established. The decrease of operational performance of a gear pump is resulted by the negative influence of hydrodynamic effects in the isolated section. This results the excessive wear of the pump parts and interferences, decrease of service life, pump delivery rate and increase of pressure and delivery pulsation, vibration and noise of the gear pump. It was determined that scientific and technical information does not have physical and mathematic models with the description of hydrodynamic processes taking place in the isolated section of a gear pump. On the basis of the analysis of scientific and technical information we suggested a working hypothesis of the research with the result to exclude the gaps in theory and practice of a gear pump concerning hydrodynamic processes taking place in the isolated section of a gear pump.Item Анализ экспериментальных исследований пульсации мгновенной подачи шестеренного насоса(КНТУ, 2013) Кулешков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Кулешкова, К. Ю.; Кулєшков, Ю .В.; Руденко, Т. В.; Красота, М. В.; Кулєшкова, К. Ю.; Kuleshkov, Yuriy; Rudenko, Timofey; Krasota, Mikhail; Kuleshkova, KseniaВ статье представлены результаты анализа результатов экспериментальных исследований пульсации мгновенной подачи и давления за рабочий цикл шестеренного насоса и сравнение их с результатами теоретических исследований. В статті представлені результати аналізу результатів експериментальних досліджень пульсації миттєвої подачі та тиску за робочій цикл шестеренного насосу і порівняння їх з результатами теоретичних досліджень. The purpose of researches is the analysis of results of known pilot studies of a pulsation of the instantaneous submission and pressure of gear-type pumps, their comparing with an analysis result of theoretical development of this scientific and technical problem for development physical and mathematical models of process of the instantaneous submission of the gear-type pump. The analysis of the publications devoted to study of a pulsation of MGP, showed extremely wide interval of dispersion of irregularity degree of submission - from 1,25% to 100% that testifies to absence of adequate theoretical basis of process of the instantaneous submission of the gear-type pump. Contradictory data on a pulsation of submission and pressure testify that the developed physical and mathematical models of process of the instantaneous submission of the gear-type pump aren't able to explain the phenomenon of a pulsation of the instantaneous submission up to the end. Absence of theoretical generalization also leads to such contradictory results as experimenters have no correct methodical approach to this difficult phenomenon. From this the output about need of carrying out new own basic theoretical and experimental researches of this complex problem follows.Item Анализ теоретических исследований пульсации мгновенной подачи шестеренного насоса(КНТУ, 2013) Кулешков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Кулешкова, К. Ю.; Кулєшков, Ю. В.; Кулєшкова, К. Ю.; Kuleshkov, Yuriy; Rudenko, Tatyana; Krasota, Mikhail; Kuleshkova, KatyaВ статье представлены результаты анализа теоретических исследований пульсации мгновенной подачи и давления в процессе рабочего цикла подачи шестеренного насоса. В статті представлені результати аналізу теоретичних досліджень пульсації миттєвої подачі і тиску в процесі робочого циклу подачі шестеренного насоса. The purpose of research is the analysis of the known theoretical studies devoted to reducing ripple instantaneous flow and pressure gear pumps. Analysis of the publications on the study instantaneous flow pulsation, showed an extremely wide range of variation of degree of uneven flow - from 1.25% to 73%. The results showed that the available scientific information on the work of an instant surge flow and pressure are contradictory and indicate that the developed physical and mathematical model of the process instantaneous flow gear pump is unable to fully explain the phenomenon of pulsation. It is a deterrent to further improve the design of pump and includes a comparative analysis of the results of theoretical and experimental data and on the basis of the new in-depth theoretical and experimental studies of the process fluid supply in gear pumps.Item Исследование закономерностей изменения геометрических параметров зубчатого зацепления шестеренного насоса(КНТУ, 2014) Кулешков, Ю. В.; Черновол, М. И.; Руденко, Т. В.; Красота, М. В.; Магопець, С. О.; Кулешкова, К. Ю.; Кулєшков, Ю. В.; Черновол, М. І.; Кулєшкова, К. Ю.; Kuleshkov, Y.; Chernovol, M.; Rudenko, T.; Krasota, M.; Magopetz, S.; Kuleshkova, K.В статье приведено доказательство теоремы об особенностях движения элементов эвольвентного зубчатого зацепления, которая является теоретической базой снижения пульсации геометрической мгновенной подачи шестеренного насоса на всем протяжении зубчатого зацепления, исключая полюс зацепления. В статті наведено доведення теореми про особливості руху елементів евольвентного зубчастого зачеплення, яка є теоретичною базою зниження пульсації геометричної миттєвої подачі шестеренного насоса протягом всього зубчастого зачеплення, крім полюса зачеплення. The objective of the research is the development of theory to create a physical and mathematical model of the process of instant feed of a gear pump. That will allow explaining the peculiarities of the instant feed and the pressure in the process of operating cycle. The article presents the proof of the theorem about special movement of the elements of evolute toothing which is the theoretical basis of the decrease of pulsation of geometrical instant feed of gear pump during all the period of toothing excluding the pitch point. We have proved the theorem of the theory of evolute toothing which determines the speed of area change described by radiuses that connect the centres of gear rotation with pitch point. The proved theorem may be used while designing gear pumps because in a gear pump the evolute toothing carries out two functions. First, toothing is used to transport hydraulic fluid from suction chamber to injection chamber and provides increase of pressure of hydraulic fluid together with other sealing elements of a pump. Second, toothing plays a traditional role of transforming of rotation moment from pump drive to driven gear. It is an additional function in a gear pump. The proof of the theorem shows that traditional image of pulsation of instant feed and pressure in the process of feed of hydraulic fluid in gear pumps is not absolutely true to the reality.Item Аналіз існуючих уявлень про механізм виникнення пульсацій миттєвої подачі шестеренного насоса(КНТУ, 2014) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Осін, Р. А.; Кулєшкова, К. Ю.; Kuleshkov, Yuriy; Rudenko, Tymofiy; Krasota, Mykhailo; Osin, Ruslan; Kuleshkova, KseniaВ статті наведені теоретичні дослідження спрямовані на розробку фізичної моделі та відповідної їй аналітичної залежності миттєвої подачі, що дозволяють пояснити причини і механізм пульсації миттєвої подачі шестеренного насоса. The objective of the research is the elaboration of a mathematical physical model of immediate flow of a gear pump which allows explaining the mechanism of occurrence of pulsations of immediate flow and pressure in the process of work cycle of a gear pump. We suggested a new physical model and a corresponding mathematical model of the process of immediate flow of a gear pump which show that the process of flow consists of two simultaneously occurring processes: the process of volume reduction which stimulates flow and the process of volume increase which blocks flow. The suggested mathematical model allows explaining the pulsating character of immediate flow of a gear pump due to the peculiarities of changes of conditional radiuses which connect the centres of gears with the contact point and while rotation they block the flow.Item Обґрунтування зменшення енерговитрат при визначені коефіцієнта подачі шестеренного насоса(КНТУ, 2012) Зозуля, В. А.; Кулєшкова, К. Ю.; Zozula, V.; Kuleshkova, К.Отримані аналітичні залежностей коефіцієнта подачі досліджуваного шестеренного насоса від відносного тиску в порівнянні з тиском еталонного насоса, який він в змозі розвинути на наперед заданому навантаженні, стали основою для розробки нового енергозберігаючого способу визначення коефіцієнта подачі досліджуваного насоса. Got analytical dependences of coefficient of serve of the probed cog-wheel pump on relative pressure as compared to pressure of standard pump, which he is able to develop on the in advance set loading, became basis for development of new energysaving method of determination of coefficient of serve of the probed pump.