Збірники наукових праць ЦНТУ

Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1

Browse

Search Results

Now showing 1 - 10 of 12
  • Item
    До визначення швидкості ковзання та зусилль, які діють в зачепленні черв’ячної передачі
    (ЦНТУ, 2017) Невдаха, Ю. А.; Дубовик, В. О.; Невдаха, А. Ю.; Пукалов, В. В.; Nevdaha, Y.; Dubovik, V.; Nevdaha, А.; Pukalov, V.
    В статті розглянута величина швидкості ковзання і її напрям відносно лінії дотикання черв’яка і черв’ячного колеса, визначені швидкості ковзання та зусилля, які діють в зачепленні. The purpose of the article is to investigate ways to increase the durability and tractive ability of worm gears. Improve the durability of worm gears by improving the working environment, as well as by applying an oil wedge. One of the ways to increase the pressure in the oil wedge, as well as increasing the loading capacity of the transmission is to change the geometry of the clutch. The article considers the value of the slip speed and its direction relative to the line of contact of the worm and worm wheel. The sliding speeds and forces that are in contact are determined. The peculiarity of a worm gear is slipping along the teeth. The magnitude of the slip velocity and its direction relative to the line of contact between the two bodies moving relative to each other, as well as the shape of the tangential surfaces, largely determine the hydrodynamic conditions of the engagement and, consequently, affect the performance of the transmission. Investigating the speed of sliding in worm gears it was found that the speed of movement of the contact line relative to the tooth of the worm wheel was small compared with the speed of the worm worm. The values of the angles formed by contact lines with directions for different points of the worm vary in a wide range. It was established that conditions for the formation of an oil wedge deteriorate with a decrease in the angle of recovery of a worm turn.
  • Item
    До розрахунку міцності різьбових з’єднань
    (КНТУ, 2016) Невдаха, А. Ю.; Дубовик, В. О.; Nevdaha, А.; Dubovik, V.
    В статті проведені дослідження метричних різьбових з’єднань, які дозволяють розраховувати коефіцієнт повноти різьби. Це дає можливість збільшити міцність різьбових з’єднань і, як результат, підвищити надійність вузла і машини в цілому. В розрахунках враховували, що сила розподілена по поверхні витка і прикладена в центрі ваги його робочої поверхні. При цьому враховували зусилля, яке руйнує тіло болта, а також силу зрізу різьби болта і зусилля зрізу витка гайки. З отриманих рівнянь зрізу для витків болта і гайки визначили коефіцієнт повноти різьби. В результаті проведених досліджень були отримані умови рівноміцності стержня болта і різьби гайки. Із співвідношень для метричних стандартних різьб і однакових матеріалів болта та гайки визначили висоту гайки, яка відповідає висоті стандартних гайок. The paper studies metric threaded connections which allow to calculate the coefficient of completeness thread. This makes it possible to increase the strength of threaded connections and as a result increase the reliability of the site and the car in general. The calculations take into account that the force is distributed over the surface of the coil and attached to the center of gravity of its working surface. This took into account the efforts that destroys the body bolt and screw thread cut power and effort slice spiral nuts. From these equations for cut turns the bolt and nut factor determined completeness thread. As a result of the research were obtained conditions rivnomitsnosti rod bolt and nut thread. With relations for metric standard thread and the same material bolt nuts and nut height determined which corresponds to the height standard screws.
  • Item
    Гвинтові фундаментні палі
    (КНТУ, 2010) Карпушин, С. О.; Невдаха, А. Ю.
    В статті наведена історія виникнення гвинтових паль, галузь застосування, переваги та недоліки, описана технологія влаштування гвинтового пальового фундаменту. History of origin of spiral piles, area of the use, advantages and failings, is resulted in Artikle, technology of device of spiral pile foundation is described.
  • Item
    Гідроізоляція фундаментів в умовах сучасного будівництва на лесових грунтах
    (КНТУ, 2010) Карпушин, С. О.; Невдаха, А. Ю.
    Висвітлено стан питання стосовно заходів щодо гідроізоляції фундаментів неглибокого закладання на лесових грунтах. Наведена узагальнена інформація відносно методів та способів гідроізоляції фундаментів. Описано властивості та принцип дії сучасних пенетруючих гідроізоляційних матеріалів. The state of question is defecate concerning measures on gidroisolation of foundations of shallow piling on loess soils. The generalized information is resulted concerning methods and methods of gidroisolation of foundations. Properties and prinzip actions of modern penetrazions of gidroisolationes materials are described.
  • Item
    Вплив неточностей заміру биття КП ланок ротора БДТ на похибку розрахунку оптимальних кутів взаємного розвороту ланок
    (КНТУ, 2012) Невдаха, А. Ю.; Nevdakha, A.
    Багатофакторним експериментом, з використанням 3D моделі типового ротора барабанно-дискового типу, досліджується вплив на похибку розрахунку оптимальних кутів повороту деталей ротора неточностей заміру биття його контрольних поверхонь. За результатами досліджень вироблені рекомендації із зменшення зазначеної похибки. За допомогою натурної моделі ротора, в лабораторії КНТУ, визначається ефективність методу двох пробних складань по відношенню до методу довільної установки дисків. Impact on the accuracy of determining the optimal angles of rotation of the rotor's parts, metering the inaccuracies beating of its control surfaces investigated by using a multifactor experiment with a 3D model of the rotor. According to the research develops recommendations to reduce the specified error. At the help of model of rotor is determined efficiency of method of two trial assembling in relation to the method of the arbitrary setting of disks.
  • Item
    Визначення впливу числа циклів навантажень на руйнування підшипників кочення
    (КНТУ, 2006) Невдаха, Ю. А.; Маломуж, Г. І.; Невдаха, А. Ю.
    В статті аналізується вплив числа циклів навантажень на руйнування підшипників кочення. На думку авторів число циклів навантажень в значній мірі впливає на руйнування підшипника в залежності від того, яке із кілець обертається відносно вектора зовнішнього навантаження - внутрішнє чи зовнішнє. In the article conducting the analysis of reasons of destruction of bearing of rolling two cases of rotation of rings are considered. It is set, that the path of internal ring and body of rolling is the most weak element, in the case when an internal ring is immobile, as contact tensions are considerably more than in the area of contact of bodies of rolling with an external ring.
  • Item
    Стенд для дослідження процесу складання роторів барабанно-дискової конструкції
    (КНТУ, 2010) Філімоніхін, Г. Б.; Невдаха, А. Ю.; Filimonikhin, G.; Nevdakha, A.
    Описуються можливості розробленого та виготовленого стенду для дослідження процесу складання роторів барабанно-дискової конструкції із заміром биттів на призмах, та на поворотному контрольному пристосуванні. Описуються деталі ротора, роторні комплекти, які з них можна сформувати, розраховується загальна кількість різних варіантів складання зазначених комплектів. Possibilities of the developed and generated stand for research of process the assembling of rotors of drum-disk construction with metrical displacement on the prisms, and on the revolving control devise are described. The details of rotor, the rotor complete sets which possible to form of them are described, accountings the common quantity of different variants of assembling specified completes.
  • Item
    До руйнування зубців зубчастих коліс
    (КНТУ, 2012) Невдаха, Ю. А.; Пукалов, В. В.; Невдаха, А. Ю.; Nevdakha, Yu.; Pukalov, V.; Nevdakha, А.
    В статті проведено конкретизацію і доповнення загальних відомостей за основними видами руйнування зубчастих коліс, рекомендовані заходи запобіганню поломки зубців. The article contains specify and addition of the general information by the main types of cogwheels destruction, also it has recommendation of the measures for prevent teeth's breakage.
  • Item
    Порівняння ефективності складання роторів барабанно-дискового типу методами двох пробних складань з заміром биття на поворотному складальному стапелі та на призмах
    (КНТУ, 2014) Невдаха, А. Ю.; Nevdaha, Andrew
    Описуються експериментальні дослідження з використанням натурної моделі ротора барабанно-дискового типу. Порівнюється ефективність методу двох пробних складань при оптимальному складані одного і того ж ротора як консольного – з заміром биття на поворотному складальному стапелі, і як міжопорного – з заміром биття на призмах. Described experimental researches of efficiency of stowage of rotors of drum-disk type by the methods of two trial stowages with intention of beating on a turning frame-clamping ship-way and on prisms. Studies are undertaken an on 3 model models of typical rotor of drum-disk type, from that it forms 15 different rotor complete sets. The stowage of these rotor complete sets was prospected with their stowage on a turning frame-clamping ship-way - as a cantilever; and on prisms - as between support. It is experimentally set that in all 100%, at the stowage of one rotor as cantilever and as between support, there will be different optimal corners and different values to the functional of quality. It is Therefore expedient to fold cantilever rotors after the method of two trial stowages after intention of beating on turning frame-clamping ship-way, and between support - after the method of two trial stowages after intention of beating on prisms.
  • Item
    Теоретичне дослідження методів вдосконалення редукторів
    (КНТУ, 2015) Невдаха, Ю. А.; Дубовик, В. О.; Невдаха, А. Ю.; Nevdaha, Yriy; Dubovik, Vіktor; Nevdaha, Andrew
    В статті проведений теоретичний аналіз методів дослідження вдосконалення редукторів. Розглянуті технологічні та конструкторські рішеня модернізації редукторів. Розглянута необхідність медернізації редукторів, внаслідок підвищення вимог до навантажувальної здатності. Запропоновано використання сучасних матеріалів при виготовлені редукторів. In article the theoretical analysis of methods of research of improvement of reducers is carried out. Considered such technological and design solutions reducers modernization as increased hardness of working surfaces of the teeth, making precision gears, gears modernization and transfers by increasing the kinematic precision manufacturing gears using higher quality materials. The necessity modernization of reducers, due to increased load capacity requirements. The use of modern materials made with gears.