Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
18 results
Search Results
Item Використання інформаційних технологій в екології та процесах охорони навколишнього середовища(ЦНТУ, 2024) Пархоменко, Ю. М.; Медведєва, О. В.; Богатирьов, Д. В.; Босько, В. В.; Кислун, О. А.; Parhomenko, Yu.; Medvedeva, О.; Bogatyryov, D.; Bosko, V.; Kyslun, О.У статті представлено результати дослідження існуючих програмних продуктів які є найбільш популярними та затребуваними в процесах екології та охорони навколишнього середовища. Подано огляд засобів автоматизованого проектування для сфери екології в Україні. Проведено огляд ринку засобів автоматизованого проектування для сфери екології, наведено їх характеристики. Представлено огляд систем комплексного керування в екології та охороні навколишнього середовища. The article presents the results of a study of existing software products that are the most popular and in demand in the processes of ecology and environmental protection. An overview of automated design tools for the field of ecology in Ukraine is given. An overview of the market of automated design tools for the field of ecology was conducted, and their characteristics were given. An overview of integrated management systems in ecology and environmental protection is presented.Item Теоретичне обґрунтування типу променевих перетворювачів при ідентифікації зернового потоку(ЦНТУ, 2022) Кондратець, В. О.; Пархоменко, Ю. М.; Пархоменко, М. Д.; Бокій, А. Р.; Kondratets, V.; Parkhomenko, Yu.; Parkhomenko, М.; Bokiy, А.Стаття присвячена теоретичному обґрунтуванню типу променевих перетворювачів при ідентифікації зернового потоку у сівалках. Розглянуто умови роботи променевих перетворювачів у процесі висівання зернових культур, види і характеристики таких перетворювачів. Показано, що найкращими характеристиками володіють оптопари, створені на базі незалежних джерела і приймача інфрачервоного випромінювання у вигляді кремнієвих діодів, що працюють у діапазоні 0,75…1,1 мкм. The article is devoted to the theoretical substantiation of the type of beam converters in the identification of grain flow in planters. The working conditions of beam transducers in the process of sowing grain crops, types and characteristics of such transducers are considered. It is shown that the best characteristics are possessed by optocouples created on the basis of independent sources and receivers of infrared radiation in the form of silicon diodes operating in the range of 0.75...1.1 μm. This publication is aimed at the implementation of means of control during the sowing of grain crops, its topic is relevant. It is directed to the implementation of the program "Technical means of the new generation for agricultural production", included in the list of State targeted scientific and scientific and technical programs, defined by the law of Ukraine "On priority areas of development of science and technology". The publication examines the theoretical justification of the type of beam transducers in devices for identifying the grain flow formed by seeding devices of seed drills, in order to increase their resolution and quality of registration of discrete objects in the flow. As a result of the analysis of the conditions for identifying the grain flow when sowing grain crops, we come to the conclusion that it is advisable to use optocouplers from separate elements "radiation source"- "radiation receiver" of the infrared spectrum that work in the range of as beam converters. Based on the fact that the registration device includes dozens of discrete optocouplers, silicon light and photodiodes should be used as IR emitters and receivers, as they are the cheapest, simpler in circuit connection than photo transistors and sufficient to obtain the necessary resolution when registering and recognizing the flow of grains.Item Бездротова локальна мережа класу Smart Home на базі модулів сплітерів-репітерів(ЦНТУ, 2021) Смірнов, В. В.; Смірнова, Н. В.; Пархоменко, Ю. М.; Smirnov, V.; Smirnova, N.; Parkhomenko, Yu.Наведено опис архітектури бездротової локальної мережі розробленої для використання в житлових приміщеннях. Описано базові модулі, розроблені для забезпечення кластеризації і сегментації груп об'єктів мережі. Модулі дозволяють розподілити загальний трафік в мережі по різних каналах, що знижує ймовірність виникнення колізій. Описана концепція роботи бездротової мережі на основі кластеризації і сегментації. Наведено структуру експериментальної бездротової мережі з низьким рівнем випромінювання на частоті 2.4 GHz. Представлений результат порівняльної оцінки рівня випромінювання між трансиверами мережі і пристроями Wi-Fi, який підтверджує правильність технічних рішень, використаних при створенні мережі. The purpose of the article is develop a wireless local area network for residential use. The article contains a description of the created channel splitter modules. The module also acts as a repeater. On the basis of repeater splitter module designed network modules hubs and switches. The hub and switch has two versions: wired and wireless. The wired version is used in conditions of a large amount of interference and a large signal attenuation. Smart Home wireless LAN is built on the splitters-repeaters modules basis, hubs and switches. The network does not support the MQTT protocol. The network is divided into clusters and segments and supports packet routing. The protocol stack is minimized. The functionality of the host and the network object is completely separated. The topology of the mobile network is not deterministic, amorphous and changes when the network objects move in space. In this case, some connections are lost and others arise. The routing tables are constantly updated. The network in accordance with the laid down algorithm, is able to build the necessary topology and organize the necessary connections in order to complete the task with a many objects. The network is capable of building packet retransmission chains for remote network objects. Thus, the wireless network implementation at its low cost allows solving a certain range of tasks. The performer can be either a separate object associated with the operator through a many repeaters. In order to increase the efficiency of the formation of routing tables and minimize the cluster structures in a wireless network. The local wireless network is designed to control an Internet of Things objects.Item ІТ в процесах створення та експлуатації об’єктів будівництва(ЦНТУ, 2020) Кислун, О. А.; Пархоменко, Ю. М.; Скриннік, І. О.; Дарієнко, В. В.; Kyslun, O.; Parhomenko, Yu.; Skrynnik, I.; Dariienko, V.; Скринник, И. А.; Дариенко, В. В.У статті представлено результати дослідження ІТ в процесах створення та експлуатації об’єктів будівництва. Подано огляд засобів комплексної автоматизації обліку в Україні. Проведено огляд ринку засобів автоматизованого проектування для архітектури та будівництва, наведено їх характеристики. Представлено огляд систем комплексного керування організацією ринку України. The article presents the results of IT research in the processes of creation and operation of construction projects. An overview of the means of complex accounting automation in Ukraine is given. An overview of the market of computer-aided design tools for architecture and construction is given also their characteristics are given. An overview of integrated market management systems in Ukraine is presented. The field of application of information technologies is constantly expanding, and growing constantly require monitoring of new implementations and search for effective innovations. Awareness provides a competitive advantage for both the developer and the consumer. Thus, the task of IT monitoring arises, and in the presence of a common area of interest, a team of like-minded people faces the problem of IT research in the processes of creation and operation of construction projects. IT in the process of creating and operating construction projects is used in all life cycles of the latter. The software that serves these processes is diverse and mostly disparate and is a set of software products aimed at sectoral use [1]. The issue of introduction of modern IT in this area is relevant and there is a need for development by specialists, which requires their study. The software used can generally be divided into: general purpose software; specialized accounting programs and other accounting systems; computer-aided design systems; integrated management systems of the organization; building management systems; scheduling systems. The so-called specialized accounting programs and accounting systems presented on the Ukrainian market in the construction sector are the same as for other sectors of the economy, there are only certain adaptations to take into account the specifics of the scope. At this stage of economic development of Ukraine in the construction industry ERP systems have not yet become widespread. Building management systems are also waiting to be expanded in Ukraine. В статье представлены результаты исследований ИТ в процессах создания и эксплуатации объектов строительства. Подан обзор средств комплексной автоматизации учета в Украине. Проведен обзор рынка средств автоматизированного проектирования для архитектуры и строительства, наведены их характеристики. Представлен обзор систем комплексного управления организацией рынка Украины.Item Analysis of the Methods for Solving Game Puzzles such as «Flip-Flop»(ЦНТУ, 2019) Parkhomenko, Yu.; Parkhomenko, M.; Rybakova, L.; Bokiy, A.; Пархоменко, Ю. М.; Пархоменко, М. Д.; Рыбакова, Л. В.; Бокий, А. Р.; Рибакова, Л. В.; Бокій, А. Р.There is a variety of popular puzzles having a goal of reducing an arbitrary binary matrix to either all “0” or “1” matrix. In this paper we study methods for solving “Flip-Flop” like puzzles of dimensions 3x3, 3x4, 4x4 applying tools of logical analysis of situations, combinatorics and discrete mathematics. We found that applying the method of sequential analysis of each combination that works well for 3x3 matrices is cumbersome and inefficient for matrices of 4x4 and higher dimensionalities. Therefore, we discovered and analyzed algorithms named trait selection method, stream method and snake method which work better. We concluded that in order to find an optimized solution it is helpful to check if each current combination matches one of the pre-final ones, or to swap «0»s with «1»s and vise versa. Существует множество популярных головоломок, целью которых является сокращение произвольной двоичной матрицы до любой матрицы «0» или «1». В этой статье мы изучаем методы решения компьютерных игр-головоломок типа «Flip-Flop», с матрицами размерностей 3x3, 3x4, 4x4, с использованием инструментов логического анализа ситуаций, комбинаторики и дискретной математики. Мы определили, что применение метода последовательного анализа каждой комбинации, который хорошо работает для матриц 3x3, является громоздким и неэффективным для матриц 4x4 и более высоких размерностей. Поэтому мы нашли и проанализировали алгоритмы, названные методом выбора признаков, методом «ручейка» и методом «змейки» , которые работают лучше. Мы пришли к выводу, что для нахождения оптимального решения полезно проверить, соответствует ли каждая текущая комбинация одной из предконечных, и своевременно вмешаться в процесс, либо предварительно обработать содержимое исходной матрицы, чтобы оптимизировать количество ячеек с кодами «0» или «1». Метою статті є визначення методів розв’язання задачі зведення довільної комбінації кодів матриці, з мінімальним числом кроків, до одних «0» або «1» та побудова алгоритмів, які забезпечать цей процес. Як показала практика гри «Flip-Flop», досягнення мети - зведення довільної комбінації кодів матриці, в результаті кінцевого числа кроків, до одних «нулів» або «одиниць», шляхом аналізу ситуацій отриманих після кожного кроку, є задачею не простою. Логіку зміни комбінацій на два, три кроки уперед важко передбачити, так як навіть в матриці з кожним кроком одночасно змінюється вміст семи комірок із 16. Тому, без визначення алгоритму послідовності дій, задача розв’язання даної головоломки, навіть при необмеженому числі кроків, не завжди досяжна. З метою визначення методів розв’язання задачі - алгоритмів виконання послідовності дій, які гарантовано або з мінімальною кількістю кроків забезпечать формування «0»-ї або «1»-ї матриці на основі довільно заданої початкової комбінації, було детально о досліджено процес формування комбінацій двійкових кодів матриці розміром m х n при активації окремих її комірок і методів прийняття рішень. У роботі приведені результати дослідження методів розв’язання комп’ютерних ігор-головоломок типу «Flip-Flop» з матрицями розміром з використанням методів логічного аналізу ситуацій, комбінаторики та дискретної математики. З’ясували, що застосування методу логічного аналізу кожної поточної комбінації, який добре працює в матрицях розміром, в матрицях і вище, для прийняття оптимального рішення при визначенні наступного кроку, є процесом складним і неефективним. Тому вирішили шукати алгоритми у визначенні постійної послідовності дій за певною ознакою. Розглянули та проаналізували методи виділення певних ознак, метод «струмка» та метод «змійки». Виконані дослідження показали, що для оптимізації кількості кроків, при застосуванні вказаних алгоритмів, необхідно аналізувати поточні комбінації і своєчасно вмішуватися в процес, або попередньо обробити вхідну матрицю, з метою оптимізації кількості комірок з кодами «0» або «1».Item Аналіз можливостей датчиків об’ємної дії, що застосовуються в діючих системах контролю висіву(ЦНТУ, 2018) Пархоменко, Ю. М.; Пархоменко, М. Д.; Бокій, А. Р.; Бокий, А. Р.; Parhomenko, Yu.; Parhomenko, M.; Bokiy, A.Проводиться аналіз технічних можливостей ємнісних і оптичних датчиків об’ємної дії, які застосовуються в діючих системах контролю висіву. Виконано ряд експериментальних і теоретичних досліджень для визначення можливостей використання датчиків об’ємної дії для реєстрації зернового потоку, що формується різними типами висівних апаратів сівалок. Доводиться, що подальша модернізація існуючих типів ємнісного та оптичного, видимої частини спектру, датчиків, як найбільш простих за конструкцією та технологією виготовлення, з метою використання їх для ідентифікації зернового потоку недоцільна і безперспективна. Проводится анализ технических возможностей емкостных и оптических датчиков объемного действия, которые применяются в действующих системах контроля высева. Выполнен ряд экспериментальных и теоретических исследований для определения возможностей использования датчиков объемного действия для регистрации зернового потока, который формируется различными типами высевающих аппаратов сеялок. Доказывается, что дальнейшая модернизация существующих типов емкостного и оптического, видимой части спектра, датчиков, как наиболее простых по конструкции и технологии изготовления, с целью использования их для идентификации зернового потока нецелесообразна и бесперспективна. The analysis of the technical capabilities of capacitive and optical sensors of volumetric action, which are used in existing seeding monitoring systems, is carried out. A number of experimental and theoretical studies have been carried out to determine the possibilities of using sensors of volumetric action to register the grain flow, which is formed by various types of seeders. A number of experimental and theoretical studies were carried out to determine the possibilities of using volumetric sensors for registration of grain flow formed by different types of seeding machines of seeders. Investigation of the functional capabilities of the capacitive sowing sensor SCS "Niva 23" was carried out with the help of a laboratory installation. Corn seeds were selected as objects of control, which gave the largest amplitude of the pulse of registration. The set speed of the seed in the plane of control of the sensor was determined by the height of its reset. When crossing the seed of the control plane of the sensor at its output, impulses were formed, the amplitude and shape of which, separated by a load resistor, was recorded by a digital oscilloscope of type HPS5 and a camera. The possibility of using capacitive and optical volumetric sensors for registration of grain flow at the output of the seeding machine and at the level of the bottom of the furrow of the drill machine SZ-3,6 was determined. The analysis of the results of the study of the grain flow formed by the coil sowing machine showed that the sensor intended for work in computer identification systems should register up to 350 ÷ 400 seeds per second, the average interval between which changes in range Tp=0,0023÷0,0063s. As a result of the received experimental data, we conclude that further upgrading of existing types of capacitive and optical, visible parts of the spectrum, sensors, as the simplest of design and manufacturing technology, with the aim of using them to identify the grain flow is inexpedient and hopeless. It is necessary to develop sensors of another type, which would provide registration to 2-3 parallely flying grains in the plane of its control.Item Розрахунок системи стабілізації температурного режиму в процесі фрикційного формоутворення(КНТУ, 2016) Пархоменко, Ю. М.; Гамалій, В. Ф.; Босько, В. В.; Parkhomenko, Y.; Gamaliy, V.; Bosko, V.Досліджено технологічний процес фрикційного формоутворення деталей. Визначено параметр, який підлягає регулюванню та передаточну функцію об’єкту управління цим параметром. Запропоновано шляхи створення автоматизованої системи стабілізації температурного режиму в процесі фрикційного формоутворення. Розроблено функціональну схему такої мікропроцесорної системи автоматичного управління температурою, яка б забезпечувала підтримку заданих значень цих параметрів в певні моменти часу та на протязі всього технологічного процесу. Studied process of forming the friction parts. Automatic control of process parameters provides friction forming temperature monitoring and support formative element temperature within 45 ÷ 75°C, ensuring stability of the process, protecting bearings from excessive heat flow and thermal discharge heat engine supports spindles. The specified temperature conditions provided by pumping oil through the bearing formative element in achieving its temperature 75°C and off the pump motor when reaching 45 °C. Certain parameters, which is subject to regulation and the transfer function of this parameter control object. The ways of creation of an automated system of stabilization of the temperature mode in the process of formation of friction. A functional diagram of a microprocessor-based system for automatic temperature control, ensuring the maintenance of set values of these parameters at specific points in time and throughout the process.Item Розробка САК змінними нормами висіву на базі сівалки СЗ-3,6(КНТУ, 2013) Пархоменко, Ю. М.; Пархоменко, М. Д.; Parhomenko, Yuriy; Parhomenko, MikhailДосліджуються шляхи створення програмно-адаптивної автоматизованої системи керування змінними нормами висіву зерновими сівалками при сівбі за технологією точного землеробства. Визначається параметр та закон регулювання. The purpose of this paper is to investigate ways to create automatic control system (ACS) variable seeding rates for precision farming technology based drills SZ-3, 6 using the upgraded device registration and authentication of computer grain flow. The ways of creating software and adaptive automated control system for variable seed rate at sowing grain drills for precision farming technology are investigated. The parameter and the control law are determined. The hardware of the automatic control system developed includes trip computer with display, GSP receiver, routing-problem variable seed rates on an electronic medium (sowing map) Sensor speed drills, drills sensor included in the work; node registration and node synchronization preprocessing and data that make up the computer system identification ( CCI ) and play the role of feedback, line of electric control unit and lever feed shaft drill seeding machines. Function block incoming data and the formation of the current values of the density distribution of grain rely on the onboard computer. Overall, the described set is a closed dynamic ACS. In addition to improving the quality of sowing, the introduction of automatic control eliminates the need for preplant setting drills seed set rate, as this is done automatically on the first meters sowing by overshoot the programmed through each turn of the supporting-wheel drive drills.Item Принципи формування та передачі даних зображення зернового потоку до ПК(КНТУ, 2008) Кондратець, В. О.; Пархоменко, Ю. М.; Пархоменко, М. Д.В даній статті досліджено принципи формування та передачі даних зображення зернового потоку до ПК, наведено схему побудови пристрою реєстрації та комп’ютерної ідентифікації зернового потоку. Визначено принцип формування двійкового коду зображення зернового потоку та передачі його до ПК за допомогою мікроконтролера та протоколу передачі даних через швидкодіючий USB інтерфейс. In this article principles of forming and transferring the image of corn stream are investigational in the personal COMPUTER, the chart of construction of device of registration and computer authentication of corn stream is resulted. Principle of forming of binary code of image of corn stream and transmission of him is certain in the personal COMPUTER by a microcontroller and protocol of communication of data through the high-speed USB interface.Item Визначення математичної моделі процесу формування зернового потоку на виході котушкового висівного апарата(КНТУ, 2011) Пархоменко, Ю. М.; Кондратець, В. О.; Пархоменко, М. Д.; Parhomenko, Y.; Kondratec, V.; Parhomenko, M.Визначено математичну модель процесу формування зернового потоку на виході котушкового висівного апарату, як функцію щільності та продуктивності сумарного потоку від часу. It is received mathematical model of the process of formation of a grain stream on an output of the bobbin sowing device, as a function of density and efficiency of a total stream from time.