Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
19 results
Search Results
Item Визначення оптимальної точки приєднання сонячної електростанції до електричної мережі методом комп’ютерного імітаційного моделювання(ЦНТУ, 2023) Плєшков, П. Г.; Зінзура, В. В.; Плєшков, С. П.; Солдатенко, В. П.; Plieshkov, Р.; Zinzura, V.; Plieshkov, S.; Soldatenko, V.Метою даного дослідження є мінімізація негативного впливу сонячної електростанції на значення усталеного відхилення напруги та рівень втрат електроенергії шляхом визначення оптимального місця її приєднання до розподільної електричної мережі. В роботі для вирішення задачі оптимального розміщення відновлюваних джерел електроенергії в електричних мережах пропонується застосовувати метод комп’ютерного імітаційного моделювання. Розроблені комп’ютерні імітаційні моделі розподільної електричної мережі з сонячною електростанцією, які дали змогу визначити оптимальне місце приєднання сонячної електростанції виходячи із значень величини втрат потужності в елементах електричної мережі на рівень усталеного відхилення напруги. Результати комп’ютерного моделювання електричної мережі з сонячною електростанцією підтвердили необхідність врахування не лише значень усталеного відхилення напруги, але і величини втрат електричної енергії в елементах мережі в процесі вибору місця встановлення сонячної електростанції. The purpose of this study is to minimize the negative impact of the solar power plant on the value of the steady voltage deviation and the level of electricity losses by determining the optimal place for its connection to the distribution network. Currently, quite a large number of methods of optimal placement of renewable sources of electricity in electrical networks have been developed. However, most of them either do not fully take into account the multifunctional influence of renewable energy sources on the parameters of the electric network regime, or are quite difficult to use. In order to solve the problem of optimal placement of renewable sources of electricity in electric networks, it is proposed to use the method of computer simulation modeling. The essence of this method is to determine the optimal place for connecting a renewable energy source to the electrical network based on the analysis of the results of computer simulation modeling of network mode parameters. This approach is the most acceptable in the case of connecting a solar power plant of average power to the electrical network of an industrial enterprise. The developed computer simulation model of a distribution electric network with a solar power plant allows for the research of network mode parameters, including the determination of the level of active power loss in network elements and the level of steady voltage deviation. The specified computer simulation models of the distribution electric network with a solar power plant made it possible to determine the optimal place for connecting the solar power plant based on the values of power losses in the elements of the electric network at the level of the established voltage deviation.Item Оптимальне керування режимами розподільних електричних мереж з сонячними електростанціями при несиметричному навантаженні(ЦНТУ, 2022) Саченко, А. І.; Плєшков, С. П.; Плєшков, П. Г.; Зінзура, В. В.; Sachenko, A.; Plieshkov, S.; Plieshkov, P.; Zinzura, V.Робота присвячена удосконаленню системи автоматичного керування режимами роботи розподільних електричних мереж, що містять сонячні електростанції з метою досягнення одночасного зниження рівнів усталеного відхилення напруги, несиметрії напруг на затискачах електроспоживачів за умови максимізації рівня генерації електроенергії сонячною електростанцією. Показано, що таку задачу автоматичного керування найдоцільніше інтерпретувати як задачу багатокритеріальної оптимізації. Обґрунтовано метод вирішення цієї задачі багатокритеріальної оптимізації. Розв’язки зазначеної задачі багатокритеріальної оптимізації можуть бути покладені в основу роботи оптимальної системи автоматичного керування параметрами режиму розподільних електричних мереж, що містять сонячні електростанції. The article is devoted to improving the system of automatic control of modes of distribution electric networks containing solar power plants in order to achieve a simultaneous reduction of steady-state voltage deviations, voltage asymmetry at the terminals of consumers while maximizing the level of electricity generation by solar power plants. Ensuring normal permissible levels of electricity quality indicators in distribution networks is one of the most pressing issues that arise in the design and operation of modern distribution networks. Deterioration of the quality of electricity in electrical networks leads to the appearance of such negative phenomena, increase in additional losses in the elements of the electrical network, reduce the service life of electrical equipment, reduce the productivity of production equipment and others. The most significant negative impact on the functioning of the elements of electrical distribution networks, including electricity consumers, is observed with increasing levels of steady-state deviation and voltage asymmetry above the normative values. Modern solar inverters allow you to control the level of steady voltage deviation at the point of their connection to the mains. The design features of the construction of inverters of solar power plants allow them to change (within certain limits) not only the level of steady-state voltage deviation, but also to affect the level of voltage asymmetry and the parameters of the reactive power mode. In view of this, the task of improving automatic control systems for the distribution of electric networks with solar power plants, the implementation of which will take into account the multifunctional influence of solar inverters on the parameters of these networks is quite relevant. For the research, a fragment of a typical distribution electrical network with a nominal voltage of 10 kV was used, which contains a solar power plant that connects directly to the 10 kV busbars. The authors of the article set the problem of controlling the parameters of the mode of distribution electric network with solar power plants in the form of the problem of multicriteria optimization. An approach to solving this problem is also proposed, which is based on the method of solving problems of multicriteria optimization by approaching the utopian point in the space of criteria. Approximate calculations are carried out, which confirm the possibility of applying the proposed approach to the construction of systems for automatic control of the parameters of the mode of distribution electrical networks with solar power plants.Item Методика визначення розрахункових навантажень промислових підприємств за питомою витратою електроенергії з використанням нестаціонарної моделі графіків електричних навантажень(ЦНТУ, 2019) Плєшков, П. Г.; Казанцев, Ю. І.; Сіріков, О. І.; Гарасьова, Н. Ю.; Величко, Т. В.; Плешков, П. Г.; Казанцев, Ю. И.; Сириков, А. И.; Гарасева, Н. Ю.; Pleshkov, P.; Kazantsev, Yu.; Sirikov, O.; Garasova, N.; Velichko, T.Запропонована методика визначення розрахункового електричного навантаження промислових підприємств за питомою витратою електроенергії та визначенням коефіцієнту максимуму на основі теорії ймовірності з використанням ергодичних теорем для нестаціонарних випадкових процесів. Дана методика може бути використана для визначення розрахункового електричного навантаження на вищих щаблях системи електропостачання - цех, корпус, підприємство. Предложенная методика определения расчетной электрической нагрузки промышленных предприятий за удельным расходом электроэнергии и определения коэффициента максимума на основе теории вероятности с использованием эргодических теорем для нестационарных случайных процессов. Данная методика может быть использована для определения расчетной электрической нагрузки на высших ступенях системы электроснабжения - цех, корпус, предприятие. The proposed methodology for determining the calculated electric load of industrial enterprises for the specific energy consumption and determining the coefficient maximum based on probability theory using ergodic theorems for non-stationary random processes. When designing power supply systems, the main initial value is the calculated electrical load. High demands are placed on the accuracy and correctness of determining the electrical load. The most common method for calculating the electrical loads of industrial enterprises is the method of ordered diagrams. It is recommended for use at the lower levels of power supply systems at the level of individual consumer groups, sections, workshops and buildings. At higher levels of electricity distribution, the application of this calculation method may be accompanied by significant errors. Therefore, its use for higher levels is not recommended. The specific energy costs of the workshops and the plant as a whole are determined using the main energy characteristics. It can be applied to certain similar enterprises. According to the specific norms of power consumption and the design performance data, the average power is determined. Knowing the average value for the time interval and the variance of the graph of the electrical load, as well as the distribution laws, it is possible to determine the estimated 30-minute maximum load for a given confidence probability. And by its value, the coefficient maximum. By multiplying the average power by the coefficient maximum, the desired design load is determined. The proposed method for calculating the electrical loads of industrial enterprises can be used for higher stages of the power supply system at the level of sections, workshops and the enterprise as a whole. The advantage of the proposed method, in contrast to the ordered diagram method, is the absence of the need to consider and take into account the characteristics of the operating modes of individual electric consumers.Item Проблеми визначення ефективності та ранжування енергоощадних заходів на об'єктах бюджетної сфери(ЦНТУ, 2019) Плєшков, П. Г.; Серебренніков, С. В.; Петрова, К. Г.; Савеленко, І. В.; Сіріков, О. І.; Плешков, П. Г.; Серебренников, С. В.; Петрова, Е. Г.; Савеленко, И. В.; Сириков, А. И.; Pleshkov, P.; Serebrennikov, S.; Petrova, K.; Savelenko, I.; Sirikov, O.Проаналізовано енергетичні особливості об’єктів бюджетної сфери за результатами енергоаудитів, розглянуто критерії оцінювання ефективності енергоощадних заходів та їх ранжування за пріоритетністю. Проанализированы энергетические особенности объектов бюджетной сферы по результатам энергоаудитов, рассмотрены критерии оценки эффективности энергосберегающих мероприятий, их ранжирование по приоритетности. The purpose of the work is to formulate and solve the problem of determining the energy efficiency of energy-saving measures when performing energy audits and ranking them by priority. We have developed investigation of energy flows of budgetary objects by conducting energy audits and finding ways to improve their energy efficiency by implementing energy-efficient measures. Energy peculiarities of the objects of the budget sphere according to the results of energy audits are analyzed, criteria of estimation of efficiency of energy saving measures and their ranking by priority are considered. Permanent tariff increases for all types of energy stimulate the search for energy savings, which will allow consumers to reduce their energy bills. In addition, to obtain financing from the state and / or local budgets, investments from international funds for the energy modernization of budgetary objects, it is necessary to justify a complex of energy-saving measures based on the results of the energy audit and the availability of energy certificates of buildings. Energy audits shows that the customer does not always clearly understand the priority of energy efficient measures and the real level of losses due to elements of fencing structures, in engineering systems of power supply, heating, ventilation etc. This leads to irrational allocation of funds for the implementation of energy efficient measures. Only a comprehensive energy audit of the building and its engineering systems will help the customer understand the tasks. The investment budget for energy efficiency measures is always limited and, as a rule, less than the amount of investment proposals, measures should be ranked in order to choose the most effective solutions. Choosing the criteria for ranking energy-saving measures is a difficult task that cannot always be based on technical and economic calculations, so it is important to search for natural and economic criteria by which energy-saving measures should be ranked in packages. The division of energy-saving measures into small and high-cost ones depends on the financial capacity of the customer and is therefore conditional. To obtain the correct results of calculating the savings from the implementation of energy-saving measures, it is necessary to focus on the baseline of energy consumption, which it is based on the design mode of operation and the regulatory microclimate in the premises. The problem of determining the baseline level of energy consumption is an urgent one and it needs further discussion and research.Item Оцінка можливостей використання термоелектричних модулів для часткового заміщення електропостачання від мережі у сільській місцевості Кіровоградської області(ЦНТУ, 2017) Плєшков, П. Г.; Плєшков, С. П.; Стець, П. Г.; Pleshkov, P.; Pleshkov, S.; Stets, P.У статті розглядається можливість використання альтернативних джерел енергії загалом і термоелектричних модулів зокрема - для часткового заміщення електропостачання від мережі у сільській місцевості. Метою статті є оцінка можливості використання альтернативних джерел енергії для часткового заміщення електропостачання від мережі у сільській місцевості Кіровоградської області. Проведено оцінку використання портативної низьковольтної термоелектрогенеруючої системи на основі елементів Пельтьє для утилізації тепла теплових втрат побутового опалення з використанням відходів лісівництва у якості паливного енергоресурсу. У результаті розгляду потенціалу альтернативних джерел енергії визначено, що жодне з розглянутих альтернативних джерел енергії не здатне у повному обсязі задовольнити потреби споживача, слід розглядати лише можливість їх комплексного використання, та компонування не з готових модулів, а з окремо підібраних елементів – для зниження ціни обладнання, оскільки собівартість 1 кВт електроенергії у такій системі буде невиправдано високою у порівнянні з живленням від мережі навіть за перспективи зростання тарифу. Тому такі пристрої слід орієнтувати на використання в умовах – де доступ до живлення від мережі повністю унеможливлений. This article considers the possibility of using the alternative energy sources in general and thermoelectric modules in particular - for partial replacement of electricity supply from the network in rural areas. The purpose of the article is to research the possibility of using alternative sources of energy for partial replacement of electricity from the network in rural areas of the Kirovograd region. The use of a portable low-voltage thermoelectric-generating system based on Peltier elements for the utilization of heat losses heating in domestic heating systems using forestry wastes as a fuel energy resource was estimated in the article. As a result of research into the potential of alternative energy sources, it is determined that none of the alternative energy sources considered is able to fully supply the consumer, and is recommended only consider the possibility of their integrated use, and the layout is not from ready modules, but from individually selected elements - to reduce the price Equipment, since the cost of 1 kW of electric power in such a system will be unreasonably high in comparison with the power supply from the grid, even taking into account the growth prospects of power supply cost. Therefore, such devices should be oriented to use in conditions - where access to power from the network is completely impossible.Item Організація системи моніторингу силових трансформаторів(КНТУ, 2010) Плєшков, П. Г.; Мануйлов, В. Ф.; Савеленко, І. В.Моніторинг силових трансформаторів – одне з широко обговорюваних питань у колах експертів виробників трансформаторів та енергоспоживальних організацій, які експлуатують ці трансформатори. Моніторинг - це постійний контроль за найбільш відповідальними або характеристичними параметрами працюючого устаткування під напругою в режимі on-line.Item Побудова системи автоматизованого управління і моніторинга енергетичних параметрів насосної станції(КНТУ, 2010) Плєшков, П. Г.; Гарасьова, Н. Ю.; Величко, Т. В.Запропонована система автоматизованого управління режимами роботи насосної установки. Система дозволяє економити електроенергію за рахунок роботи частотно-регульованого приводу залежно від реального вжитку води та забезпечити ефективність моніторингу та управління основними режимами водозабірного вузла.Item Оптимізація процесу використання електричної енергії за результатами енергоаудиту(КНТУ, 2016) Плєшков, П. Г.; Бондаренко, В. Б.; Серебренніков, С. В.; Савеленко, І. В.; Петрова, К. Г.; Pleshkov, Petr; Bondarenko, Volodimir; Serebrennikov, Sergiy; Savelenko, Ivan; Petrova, KaterynaОптимізація процесу використання електричної енергії та економія в оплаті активної та реактивних енергій досягнуто за результатами комплексного енергоаудиту. Модернізація систем освітлення дозволило скоротити електроспоживання вдвічі. Reducing the cost of funds for the purchases of the energy resources by increasing the level of the energy efficiency. The methods of comprehensive complex energy audit and analysis of the synthetic fuel and energy balance are used. The possibilities of the energy saving are found and their ranking in order of priority of their implementation is conducted. Taking into account the specificity of the object of the energy audit and the peculiarities of the regimes of the energy usage allowed to improve the model of the energy management system, which is to perform oversight functions concerning compliance of the norms and regimes of the energy usage and allows to systematize the priority tendencies and projects to increase the energy efficiency. Results of the energy research allowed finding out the reserves of the energy saving and reducing costs on the payment for the energy carriers.Item Розробка та експериментальне дослідження фіксатора коротких замикань для повітряних електричних мереж напругою 110 – 150 кВ(КНТУ, 2016) Котиш, А. І.; Плєшков, П. Г.; Орлович, А. Ю.; Сіріков, О. І.; Некрасов, А. В.; Kotysh, Andrij; Pleshkov, Petro; Orlovich, Anatoliy; Sirikov, Oleksandr; Nekrasov, AndrijНа основі аналізу схеми нормального режиму мережі 150 кВ ПАТ «Кіровоградобленерго» встановлено, що існує ряд підстанцій, де встановлення фіксаторів короткого замикання просто необхідно. Вибрано оптимальний варіант конструкції фіксатора короткого замикання, розроблено його кінематичну схему, визначено зв’язки між переміщеннями частин механізму приладу та виконано його силовий розрахунок. Розроблено конструкцію фіксатора короткого замикання, виконано його розрахунок магнітної системи, що дозволило побудувати вебер-амперні та тягові характеристики приладу. Проведено експериментальні дослідження та лабораторні випробування фіксатора короткого замикання. В результаті чого визначено пороги спрацьовування пристрою в функції струму та часу, побудовано його характеристики. Експериментом підтверджено повну придатність приладу для роботи в реальних умовах. The article is dedicated to improving reliability of electric networks with voltage 110-150 kV by application developed special devices latch short circuit. Based on the analysis circuit normal 150 kV network PAC "Kirovogradoblenergo" found that a number of stations where installation clamps short circuit is necessary. Your best option holder short circuit designs developed his kinematic scheme defined relationships between parts movement mechanism unit and executed his power calculation. The design retainer short circuit, made his calculation of the magnetic system, which allowed to build Weber-voltage and traction device. Experimental studies and laboratory tests latch short circuit. As a result, defined thresholds triggering device as a function of current and time, built its characteristics. Experiment confirmed the full applicability of the device to work in real conditions.Item Визначення економічної ефективності комплексної електроенергетичної системи для сільського господарства(КНТУ, 2010) Плєшков, П. Г.; Солдатенко, В. П.; Pleshkov, P.; Soldatenko, V.У статті приведений аналіз можливих варіантів економічної оцінки роботи комплексної електроенергетичної системи з відновлюваними джерелами енергії в ринкових умовах. In the article the resulted analysis of possible variants of economic evaluation of work of the complex electroenergy system is with refurbishable energy sources in market conditions.