Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
3 results
Search Results
Item Аналіз теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса(ЦНТУ, 2017) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Красота, М. В.; Руденко, Т. В.; Kuleshkov, Y.; Magonets, E.; Kuleshkova, K.; Krasota, M.; Rudenko, T.В статті наведені результати аналізу теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса. Встановлені теоретичні залежності об’єму відсіченої порожнини від параметрів зубчастого зачеплення, а також від положення точки зачеплення на лінії зачеплення шестерень насоса. Отримані теоретичні залежності дозволяють визначити геометричні параметри відсіченої порожнини, при яких виключається явище компресії робочої рідини. Виключення компресії досягнуто завдяки використанню зубчастого зачеплення з асиметричною лінією зачеплення. В роботі вказані недоліки існуючих теоретичних досліджень і вказані напрямки подальшого їх розвитку.The objective of research is to analyze scientific and technical information on the results of theoretical studies of the geometric parameters of the cut-off housing of the gear pump and to determine future direction of research of the processes that take place in the cut-off housing and to formulate the scientific hypothesis of the research. The article presents the results of the analysis of theoretical studies of geometric parameters of the cut-off housing of the gear pump. The theoretical dependences of the volume of the housing on the parameters of toothing were established as well as the position of the point of engagement on the line of contact of a gear pump. The theoretical dependences allow determining geometrical parameters of the cut-off housing which eliminate the phenomenon of the working fluid compression. The avoidance of compression is achieved through the use of toothing with asymmetrical engagement line. The work indicates the shortcomings of existing theoretical research and presents the directions of further development. It was established that one of the possible ways to reduce the impact of the compression of the working fluid in the cut-ff housing is to use toothing with asymmetric line engagement.Item Аналіз гідродинамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса(КНТУ, 2016) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Руденко, Т. В.; Красота, М. В.; Kuleshkov, Y.; Mahonets, E.; Kuleshkova, K.; Rudenko, T.; Krasota, M.В статті наведені результати аналізу впливу динамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса на його працездатність. Зазначені умови виникнення компресії і декомпресії робочої рідини у відсіченій порожнині шестеренного насоса. Встановлено взаємозв’язок між компресією і декомпресією робочої рідини, що виникають у відсіченій порожнині шестеренного насоса і негативним впливом цих явищ на працездатність насоса. Зазначено зниження працездатності шестеренного насоса внаслідок негативного впливу гідродинамічних явищ у відсіченій порожнині, що виявляється у підвищеному зношуванні деталей і з’єднань насоса, зниженні довговічності, коефіцієнту подачі, підвищенні пульсації тиску і подачі, збільшенні вібрацій і шуму НШ. The objective of the work is to analyse scientific and technical information and to determine further directions of research of processes taking place in the isolated section of a gear pump and to formulate scientific hypothesis of the research. The article presents the analysis results of the influence of dynamic processes taking place in the isolated section of a gear pump on its operational performance. The conditions of the occurrence of compression and decompression of hydraulic oil in the isolated section of a gear pump were determined. The interrelationship between the compression and decompression of the hydraulic oil which occurs in the isolated section of a gear pump and the negative influence of these effects on the operational performance of a pump was established. The decrease of operational performance of a gear pump is resulted by the negative influence of hydrodynamic effects in the isolated section. This results the excessive wear of the pump parts and interferences, decrease of service life, pump delivery rate and increase of pressure and delivery pulsation, vibration and noise of the gear pump. It was determined that scientific and technical information does not have physical and mathematic models with the description of hydrodynamic processes taking place in the isolated section of a gear pump. On the basis of the analysis of scientific and technical information we suggested a working hypothesis of the research with the result to exclude the gaps in theory and practice of a gear pump concerning hydrodynamic processes taking place in the isolated section of a gear pump.Item Исследование закономерностей изменения геометрических параметров зубчатого зацепления шестеренного насоса(КНТУ, 2014) Кулешков, Ю. В.; Черновол, М. И.; Руденко, Т. В.; Красота, М. В.; Магопець, С. О.; Кулешкова, К. Ю.; Кулєшков, Ю. В.; Черновол, М. І.; Кулєшкова, К. Ю.; Kuleshkov, Y.; Chernovol, M.; Rudenko, T.; Krasota, M.; Magopetz, S.; Kuleshkova, K.В статье приведено доказательство теоремы об особенностях движения элементов эвольвентного зубчатого зацепления, которая является теоретической базой снижения пульсации геометрической мгновенной подачи шестеренного насоса на всем протяжении зубчатого зацепления, исключая полюс зацепления. В статті наведено доведення теореми про особливості руху елементів евольвентного зубчастого зачеплення, яка є теоретичною базою зниження пульсації геометричної миттєвої подачі шестеренного насоса протягом всього зубчастого зачеплення, крім полюса зачеплення. The objective of the research is the development of theory to create a physical and mathematical model of the process of instant feed of a gear pump. That will allow explaining the peculiarities of the instant feed and the pressure in the process of operating cycle. The article presents the proof of the theorem about special movement of the elements of evolute toothing which is the theoretical basis of the decrease of pulsation of geometrical instant feed of gear pump during all the period of toothing excluding the pitch point. We have proved the theorem of the theory of evolute toothing which determines the speed of area change described by radiuses that connect the centres of gear rotation with pitch point. The proved theorem may be used while designing gear pumps because in a gear pump the evolute toothing carries out two functions. First, toothing is used to transport hydraulic fluid from suction chamber to injection chamber and provides increase of pressure of hydraulic fluid together with other sealing elements of a pump. Second, toothing plays a traditional role of transforming of rotation moment from pump drive to driven gear. It is an additional function in a gear pump. The proof of the theorem shows that traditional image of pulsation of instant feed and pressure in the process of feed of hydraulic fluid in gear pumps is not absolutely true to the reality.