Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
10 results
Search Results
Item Дослідження конструкції дискового пружинного загортача просапної сівалки(ЦНТУ, 2024) Артеменко, Д. Ю.; Кислун, О. А.; Онопа, В. А.; Богатирьов, Д. В.; Artemenko, D.; Kyslun, O.; Onopa, V.; Bogatyryov, D.В роботі представлено результати теоретичних досліджень параметрів дискового пружинного загортача просапної сівалки. В результаті проведеного аналізу по розташуванню загортачів в конструкції секції було встановлено, що ефективніше розташовувати загортачі після сошника, що дозволяє укривати насіння вологим шаром ґрунту та створювати сприятливі умови для його проростання. З метою підвищення ефективності роботи загортачів був розроблений новий дисковий загортач пружинного типу. У процесі його дослідження було визначено, що основними параметрами, які впливають на процес роботи загортача є його кут атаки, швидкість руху сівалки та дальність переміщення ґрунту в бік борозни. Отримана теоретична залежність, що показує вплив кута атаки на дальність переміщення ґрунту загортачем в залежності від фізико-механічних властивостей ґрунту. The study presents the results of theoretical research on the design and technological parameters of the spring-loaded disc covering device for row crop seeders. The analysis of existing covering devices and their technological processes revealed that they do not provide optimal sequential seed covering with moist soil layers followed by drier ones. Most designs, positioned after pressing rollers, primarily perform mulching and leveling of the furrow surface, which leads to mixing soil layers of different depths. It was determined that placing the covering devices immediately after the seed opener is more effective. This allows seeds to be covered with a moist soil layer immediately after being placed in the furrow, followed by a mulched drier layer. This approach helps retain moisture in the seed zone and creates favorable conditions for germination. To address the shortcomings of the reviewed covering devices, a new spring-loaded disc covering device was developed. This device combines a flat, single-edged disc positioned at an angle of attack to the direction of movement. A conical press is mounted on the outer edge of the disc, connected via a hub to a vertical pressure spring. The vertical pressure spring applies force to the working surface of the covering device and is positioned at an angle in the vertical plane relative to the row axis.Item Математична модель верхнього робочого елемента механічно-пневматичного збирача комах-шкідників пасльонових культур(ЦНТУ, 2024) Онопа, В. В.; Артеменко, Д. Ю.; Кислун, О. А.; Онопа, В. А.; Onopa, V.; Artemenko, D.; Kyslun, O.; Onopa, V.В роботі наведені результати пошукових теоретичних досліджень конструктивних особливостей верхнього робочого елементу пристрою для механічно-пневматичного збирання комах-шкідників пасльонових культур. Під час аналізу наукових джерел було встановлено, що комахи-шкідники значною мірою призводять до серйозних втрат у світовому виробництві сільськогосподарської продукції. Пестицидний обробіток є основним методом боротьби з ними, проте така практика призводить до забруднення навколишнього середовища, загрози здоров'ю людини та підвищення ризику захворювань. У зв'язку з цим велика увага приділяється розробці екологічно безпечних методів боротьби. Виявлено, що одним з найбільш ефективних методів є фізичне збирання комах-шкідників пристроями різної дії. Тому подальша розробка нових конструкцій пристроїв для виконання процесу збирання комах шкідників є актуальною задачею. З цією метою був запропонований новий пристрій для збирання комах-шкідників, призначений для ефективного збирання шкідників пасльонових культур за допомогою механічнопневматичного методу. Теоретично обґрунтована конструкція верхнього робочого елемента пристрою для збирання комах-шкідників і встановлено, що кут атаки робочої поверхні пристрою лежить в межах від 10 до 60°. Ефективність запропонованої конструкції нового пристрою забезпечується підвищеним впливом механічної дії на рослину пасльонових культур без її ушкодження і виключенням втримання шкідника на всіх рівнях по висоті рослини, максимальним збиранням шкідників за один прохід пристрою. The paper presents the results of exploratory theoretical studies of the design features of the upper working element of the device for the mechanical-pneumatic collection of insect pests of nightshade crops. During the analysis of scientific sources, it was established that insect pests to a large extent lead to serious losses in the world production of agricultural products. Pesticide treatment is the main method of combating them, but this practice leads to environmental pollution, threats to human health and increased risk of diseases. In this regard, great attention is paid to the development of ecologically safe methods of control. It was found that one of the most effective methods is the physical collection of insect pests with devices of various effects. Therefore, the further development of new designs of devices for carrying out the process of collecting insect pests is an urgent task.Item Теоретичне обґрунтування конструктивних особливостей котка для передпосівного обробітку ґрунту(ЦНТУ, 2023) Артеменко, Д. Ю.; Онопа, В. А.; Кислун, О. А.; Муленко, К. А.; Artemenko, D.; Onopa, V.; Kyslun, O.; Mulenko, K.В статті наведені результати пошукових теоретичних досліджень конструктивних особливостей котка для передпосівного обробітку ґрунту. Аналіз існуючих конструкцій сучасних прикочуючих котків для передпосівного обробітку ґрунту і технологічного процесу, який вони виконують, показав, що на сьогоднішній день номенклатура конструкцій зростає, універсальність падає, під кожен тип робіт потрібен свій коток, суцільне формування ущільненого дна посівного ложа сучасними котками в повній мірі не виконується. Встановлено, що більш раціональним буде технологічний процес коли прикочування відбувається не лише у верхніх шарах ґрунту, а і у нижніх. З цією метою був запропонований комбінований прикочуючий коток з робочими елементами кулачкового типу. Розроблена математична модель взаємодії прикочуючого котка і його елементів з ґрунтом. Запропонована математична модель процесу роботи удосконаленого котка дозволяє встановити характер розподілення питомого тиску в залежності від конструктивних параметрів елементів котка і фізико- механічних властивостей ґрунту. Ефективність запропонованої конструкції прикочуючого котка забезпечується тим, що за рахунок конструкції робочої поверхні та кулачків можна забезпечити рівномірне ущільнення ґрунту по ширині захвату котка і на потрібну глибину та зменшення кількості проходів котка для забезпечення необхідної рівномірності ущільнення. The article presents the results of exploratory theoretical studies of the design features of a roller for pre-sowing tillage. According to the number of operations, the rolling roller can be considered as one of the main means for ensuring high-quality preparation of the field for sowing. Therefore, the rolling process must be considered as a complex of operations, and its construction as a combination of the latter. The technological process of rolling helps to optimally place the seeds at a given depth, improves the contact between the seeds and the soil, and contributes to the rapid swelling and germination of the seeds. The main purpose of rolling is to conserve soil moisture, especially in arid conditions, by reducing physical evaporation. The analysis of the existing designs of domestic and foreign manufacturers of rolling rollers for presowing soil cultivation and the technological process they perform showed that today the range of designs is growing, versatility is decreasing, each type of work requires its own roller, continuous formation of the compacted bottom of the seedbed with modern rollers in is not fully implemented. The main direction on which foreign roller manufacturers are working is strip rolling and preparation of the seed bed directly along the track of the coulters if the roller is part of the seeding unit. In addition to the classic ones, there are practically no cats for continuous rolling in the company's assortment. It has been established that the technological process will be more rational when rolling occurs not only in the upper layers of the soil, but also in the lower ones. For this purpose, a combined rolling roller with working elements of the cam type was proposed. A mathematical model of the interaction of the rolling roller and its elements with the soil has been developed. The proposed mathematical model of the working process of the improved roller allows to establish the nature of the specific pressure distribution depending on the constructive parameters of the roller elements and the physical and mechanical properties of the soil. The effectiveness of the proposed design of the rolling roller is ensured by the fact that due to the design of the working surface and cams, it is possible to ensure uniform compaction of the soil along the width of the grip of the roller and to the required depth and reduce the number of passes of the roller to ensure the necessary uniformity of compaction.Item Результати експериментальних досліджень пневматичного збирання шкідників сільськогосподарських культур(ЦНТУ, 2022) Онопа, В. А.; Артеменко, Д. Ю.; Onopa, V.; Artemenko, D.В статті наведені результати експериментальних досліджень пневматичного збирання шкідників сільськогосподарських культур. На сьогоднішній день комахи-шкідники є однією з головних проблем у сільському господарстві. Шкідники щороку спричиняють від 20 до 40 відсотків втрат світового виробництва сільськогосподарських культур, основним методом боротьби з якими є пестицидна обробка. Безперервне використання пестицидів призводить до потенційних людських захворювань, забруднення рослин і ґрунту, тому велика увага приділена методам екологічної боротьби. Пневматичне збирання шкідників є основним і максимально ефективним засобом боротьби. А розробка нових конструкцій і пристроїв для його виконання є актуальною задачею. В роботі запропонована конструкція пневмодезинсектора для пневматичного збирання шкідників сільськогосподарських культур та досліджена ефективність його роботи. Експериментальні дослідження запропонованого пневмодезинсектора показали, що в середньому за триразовий збір ефективність становила: на озимій пшениці - 74,0%, на люцерні – 60%, на картоплі 68,3%, на баклажанах – 78,5%, на томатах – 79,3%, на перці солодкому – 91,0%. Кількість рослин, уражених вірусами, зменшилася у 1,2 рази порівняно з контролем без пневмодезинсекції. Витрати застосування хімічного захисту перевищували витрати на пневмодезинсекцію в 4,7 рази. The article presents the results of experimental research on the pneumatic collection of pests of agricultural crops. Today, insect pests are one of the main problems in agriculture. Pests cause 20 to 40 percent of global crop losses every year, and pesticide treatment is the main method of control. The continuous use of pesticides leads to potential human diseases, plant and soil pollution, so much attention is paid to ecological control methods. Pneumatic collection of pests is the main and most effective means of control. And the development of new designs and devices for its implementation is an urgent task. The analysis of the constructions and researches of pneumatic machines for harvesting pests of agricultural crops allowed us to come to the conclusion that recently, machines with a pneumatic harvesting system are most often used for harvesting pests, as those that damage the plant the least. Due to their efficiency, pneumatic machines of the suction type are becoming the most popular. The use of machines of this type will make it possible to obtain ecologically clean food products without the use of chemical means of control. In the work, the design of the pneumodisinfector and the device for the pneumatic collection of pests of agricultural crops is proposed and the efficiency of its operation is investigated. Experimental studies of the proposed pneumodisinfectant sector showed that, on average, for three harvests, the effectiveness was: on winter wheat - 74.0%, on alfalfa - 60%, on potatoes - 68.3%, on eggplant - 78.5%, on tomatoes - 79, 3%, sweet pepper – 91.0%. The number of plants affected by viruses decreased by 1.2 times compared to the control without pneumodisinfection. The costs of applying chemical protection exceeded the costs of pneumodisinfection by 4.7 times. On the basis of the obtained data, in the conditions of production crops of winter wheat, alfalfa, eggplant and potatoes, the use of a pneumodisinfector is an effective method.Item Дослідження і обгрунтування конструкції пружинного загортача просапної сівалки(ЦНТУ, 2022) Артеменко, Д. Ю.; Онопа, В. А.; Artemenko, D.; Onopa, V.В статті наведені результати пошукових теоретичних досліджень конструктивних і технологічних параметрів пружинного загортача просапної сівалки. Аналіз існуючих конструкцій загортачів і технологічного процесу який вони виконують показав, що на сьогоднішній день вимоги до загортання насіння спочатку вологими шарами ґрунту, а потім більш сухими, сучасними загортачами не виконуються. В більшості посівних секцій загортачі розміщують після прикочуючих котків і вони виконують функцію по мульчуванню і плануванню поверхні борозни перемішуючи шари ґрунту різних горизонтів. Встановлено, що більш раціональним буде технологічний процес загортання насіння загортачами які спочатку укривають його нижніми вологими шарами ґрунту, а потім мульчованим більш сухим шаром, при цьому загортачі необхідно встановлювати після сошника для можливості укривати насіння одразу після потрапляння в борозну. Теоретично встановлено, що при роботі розробленого загортача найбільший вплив на тяговий опір здійснюють глибина ходу загортача та швидкість руху, а найменше нахил робочої поверхні. Отримана теоретична залежність яка зв’язує конструктивні і технологічні параметри пружинного загортача і їх вплив на основну характеристику його роботи – тяговий опір. The article presents the results of exploratory theoretical studies of the constructive and technological parameters spring wrapper of the precision seed drill. The analysis of the existing designs of wrappers and the technological process they perform showed that today the requirements for wrapping seeds first with wet layers of soil and then with drier, modern wrappers are not met. In most sowing sections, wrappers are placed after the rolling rollers and they perform the function of mulching and planning the surface of the furrow by mixing soil layers of different horizons. It was established that the technological process of wrapping the seeds with wrappers, which are first covered with the lower moist layers of the soil, and then with a drier mulch layer, will be more rational, while the wrappers must be installed after the coulter, which is able to cover the seeds immediately after entering the furrow. Since the main disadvantage of the existing wrappers is the mixing of soil layers during their operation, an improved design of the wrapper was developed. The wrapper, which is made of a spring and has several component parts, has a torsion spring and a rod in the upper part, in the lower part of which there is a working surface in the form of a two-level rectangular trihedral inclined prism, moreover, the upper level of the working surface is twice as long as the lower one, and the installation angle of the working surface is smaller than the angle of friction of the soil on the steel. The efficiency of the wrapper is ensured by the following factors: due to the increased length of the upper working surface of the wrapper, the dry soil of the upper layer covers the furrow, which is already covered by the lower moist layers of the soil; due to the lateral action of the wrapper on the soil layer and the operation of the spring, a mulching effect is created; when the soil is more clogged with plant remains, the design of the spring wrapper contributes to its self-cleaning. The process of interaction of the working surface wrapper with the soil and the influence of its design on the technological characteristics of the technological process are theoretically considered. The main technological characteristic of the wrapper is its tensile strength. It was established that during the operation of the developed wrapper, the greatest influence on the traction resistance is exerted by the depth of the movement wrapper and the speed of movement wrapper, and the least by the inclination of the working surface. The obtained theoretical dependence connects the design and technological parameters of the spring wrapper and their influence on the main characteristic of its operation - traction resistance.Item Experimental researches of a precision seed drills coulter equipped with a disk seedbed former(ЦНТУ, 2019) Artemenko, D.; Onopa, V.; Артеменко, Д. Ю.; Онопа, В. А.The furrow opener coulter is the most commonly used on precision seed drills. It is also used on the seeding section of the seed drill UPS 12. Due to such a design, the coulter guarantees the formation of a compacted seed bed, as well as the walls of the furrow, which help to pull the capillary moisture to seeds. But the main disadvantage of this design is the seeds redistribution along the furrow sole as the result of the displaced topsoil effect, which is shedded behind the rear wall of coulter side panels. There is proposed an improved design of the UPS 12 seed drill coulter that is equipped with a disk seedbed former and eliminates the above-mentioned disadvantage. Under laboratory conditions, there were conducted comparative experimental researches of series-produced and advanced coulters. The obtained tests' results made it possible to ascertain the advantage, with regard to the performance quality of technological process, of the coulter with a disk seedbed former. На сучасному етапі розвитку сільського господарства, підвищення врожайності просапних культур, можливе за умови постійного вдосконалення робочих органів, які приймають участь у головній операції вирощування – посіву. Основним органом сівалки який безпосередньо впливає на якість посіву є насіннєвий сошник і елементи його конструкції. Найбільшого розповсюдження на просапних сівалках набув наральниковий сошник який і використовується на посівній секції сівалки УПС 12. Такий сошник, за рахунок своєї конструкції, забезпечує формування ущільненого насіннєвого ложа, а також стінок борозни, що сприяє підтягуванню капілярної вологи до висіяного насіння. Але основним недоліком такої конструкції є перерозподіл насіння по дну борозни за рахунок дії на нього зрушеного верхнього шару ґрунту, який осипається за заднім обрізом щік сошника. Запропонована удосконалена конструкція сошника сівалки УПС 12 яка оснащена дисковим ложеутворювачем і усуває вказаний недолік. Проведені порівняльні експериментальні дослідження серійного і удосконаленого сошників в лабораторних умовах. Отримані результати випробувань дозволили встановити перевагу, по якості виконання технологічного процесу, сошника із дисковим ложеутворювачем. В результаті проведених досліджень встановлено, що основним недоліком серійного сошника є перерозподіл насіння по дну борозни в процесі його укладання. На основі аналізу роботи серійного сошника та проведених експериментальних досліджень розроблена удосконалена конструкція сошника, яка має дисковий ложеутворювач. В результаті проведених експериментальних досліджень встановлено, що використовуючи сошник із дисковим ложеутворювачем забезпечується більш висока якість посіву в середньому на 15,3%. Наибольшее распространение на пропашных сеялках приобрел наральниковый сошник который и используется на посевной секции сеялки УПС 12. Такой сошник, за счет своей конструкции, обеспечивает формирование уплотненного семенного ложа, а также стенок борозды, способствует подтягиванию капиллярной влаги к высеянным семенам. Но основным недостатком такой конструкции является перераспределение семян по дну борозды за счет воздействия на него сдвинутого верхнего слоя почвы, который осыпается за задним обрезом щек сошника. Предложена усовершенствованная конструкция сошника сеялки УПС 12 оснащенная дисковым борознообразователем и устраняет указанный недостаток. Проведены сравнительные экспериментальные исследования серийного и усовершенствованного сошников в лабораторных условиях. Полученные результаты испытаний позволили установить преимущество по качеству выполнения технологического процесса, сошника с дисковым бороздообразователем.Item Дослідження траєкторії руху домішок в повітряному потоці(КНТУ, 2009) Онопа, В. В.; Петренко, М. М.; Кислун, О. А.; Онопа, В. А.; Опора, V.; Petrenko, М.; Kislun, О.; Onopa, V.В статті зроблено спробу дослідження траєкторії руху домішок в повітряному потоці при його очищенні, для підвищення ефективності роботи зерноочисних машин з замкнутим циклом повітряного потоку. Показано можливі траєкторії руху домішки при всмоктуванні суміжними щілинами в залежності від її попадання в одну із зон дії жалюзі. In the article the attempt research of trajectory motion of admixtures is done in the current air at his cleaning, for the increase of efficiency work grain cleaners with the reserved cycle of current air. The possible trajectories of motion admixture are rotined at suction contiguous cracks depending on its hit in one of areas of action of jalousies.Item Ефективність уловлювання шкідників пневматичною насадкою пневмодезинсектора(КНТУ, 2010) Петренко, М. М.; Онопа, В. А.; Кислун, О. А; Petrenko, М.; Onopa, V.; Kislun, О.В статті розглянуто роботу пневматичної насадки пневмодезинсектора при збиранні шкідників з насаджень картоплі. Розглянуто вплив дії всмоктуючого факел пневматичної насадки пневмодезинсектора на ефективність уловлювання шкідника підчас реагування його небезпеку. За допомогою пакету прикладних програм на ПЕОМ, отримали графічну залежність теоретичного значення ефективності (Е) уловлювання від швидкості руху агрегату Vагр. In the article work of pneumatic attachment of pnevmodezinsektora is considered at collection of wreckers from planting of potato. Influence of action is considered vsyvayuschego torch of pneumatic attachment of pnevmodezinsektora on efficiency of catching of wrecker of the vovrem'ya reacting him on a danger. With a help to the application package on PEOM, got graphic dependence of theoretical value of efficiency (Е) catching from the rate of movement of asm Vagr.Item Обґрунтування раціональної форми направляючої поверхні живильного пристрою для пневмосепарації зерна(КНТУ, 2012) Нестеренко, О. В.; Богатирьов, Д. В.; Онопа, В. А.; Якімцов, В. П.; Nesterenko, O.; Bohatyrov, D.; Onopa, V.; Jkimcov, V.В статті проведено теоретичне обґрунтування основних параметрів багаторівневого гравітаційного живильного пристрою для підвищення продуктивності та зменшення опору повітряному потоку в пневмосепаруючому каналі (ПСК). In this paper a theoretical justification of the basic parameters of a multi-level gravity feeder for increased productivity and reduced resistance to air flow in the channel of pneumatic separation.Item Дослідження працездатності пари тертя "гальмівний диск - гальмівна колодка" легкового автомобіля(КНТУ, 2010) Бевз, О. В.; Магопець, С. О.; Онопа, В. А.; Bevz, O.; Magopec, S.; Onopa, V.В статті розглянутий вплив пари тертя "гальмівний диск – гальмівна колодка" на безпеку руху автомобіля. За допомогою сучасних методів металографічного й мікрорентгеноспектрального аналізу було встановлено характер протікання дійсного процесу тертя в парі "гальмівний диск – гальмівна колодка" та визначено оптимальний склад матеріалу гальмівної колодки й диску, що дало змогу зменшити величини їх спрацювання та підвищити довговічність пари тертя. Додаткові дослідження впливу полімерного матеріалу нанесеного на робочі поверхні гальмівної колодки та гальмівного диску не дали бажаного позитивного ефекту та зменшили ефективність гальмування. In the article influence of pair of friction is considered a "brake disk is a skid" on safety of motion of car. By the modern methods of metallographic and mikrorentgenospectral analysis character of flowing of actual process of friction was set in a pair a "brake disk is a skid" and optimum composition of material of skid and disk is certain, which enabled to decrease the sizes of their wearing-out and promote longevity of pair of friction.