Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
3 results
Search Results
Item Особенности работы и конструкции шестеренного насоса(ЦНТУ, 2017) Кулешков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Магонец, Е. В.; Осин, Р. А.; Кулєшков, Ю. В.; Магонець, Є. В.; Осін, Р. А.; Kuleshkov, Yu.; Rudenko, T.; Krasota, M.; Magonets, E.; Osin, R.В статье рассмотрены особенности конструкции шестеренного насоса, объясняющие его высокий уровень удельной мощности в сравнении с другими типами объемных насосов. Представлены в виде моделей характерные особенности работы шестеренного насоса, что позволило сформулировать пути дальнейшего усовершенствования конструкции шестеренного насоса в направлении повышения его технического уровня. В статті розглянуті особливості конструкції шестерінчастого насоса, які пояснюють його високий рівень питомої потужності у порівнянні з іншими типами об’ємних насосів. Представлено у вигляді моделей характерні особливості роботи шестеренного насоса, що дозволило сформулювати шляхи подальшого удосконалювання конструкції шестеренного насоса в напрямку підвищення його технічного рівня. The objective of research is to explain certain aspects of gear-type pump work, understanding of which allows to formulate tasks of farther increasing its technical level. The article describes the special aspects of construction gear-type pump, which explains its high level of unit power in comparison with other kinds of massive pumps. Submitted in a form typical aspects of gear-type pump work, which allows to formulate the ways of farther upgrading the gear-type pump construction towards increasing its technical level. Offered schemes of work allows to explain such negative feature in the gear-type pump as split off void, pulsating of pressure and giving in causal-resultative categories.Item Аналіз теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса(ЦНТУ, 2017) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Красота, М. В.; Руденко, Т. В.; Kuleshkov, Y.; Magonets, E.; Kuleshkova, K.; Krasota, M.; Rudenko, T.В статті наведені результати аналізу теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса. Встановлені теоретичні залежності об’єму відсіченої порожнини від параметрів зубчастого зачеплення, а також від положення точки зачеплення на лінії зачеплення шестерень насоса. Отримані теоретичні залежності дозволяють визначити геометричні параметри відсіченої порожнини, при яких виключається явище компресії робочої рідини. Виключення компресії досягнуто завдяки використанню зубчастого зачеплення з асиметричною лінією зачеплення. В роботі вказані недоліки існуючих теоретичних досліджень і вказані напрямки подальшого їх розвитку.The objective of research is to analyze scientific and technical information on the results of theoretical studies of the geometric parameters of the cut-off housing of the gear pump and to determine future direction of research of the processes that take place in the cut-off housing and to formulate the scientific hypothesis of the research. The article presents the results of the analysis of theoretical studies of geometric parameters of the cut-off housing of the gear pump. The theoretical dependences of the volume of the housing on the parameters of toothing were established as well as the position of the point of engagement on the line of contact of a gear pump. The theoretical dependences allow determining geometrical parameters of the cut-off housing which eliminate the phenomenon of the working fluid compression. The avoidance of compression is achieved through the use of toothing with asymmetrical engagement line. The work indicates the shortcomings of existing theoretical research and presents the directions of further development. It was established that one of the possible ways to reduce the impact of the compression of the working fluid in the cut-ff housing is to use toothing with asymmetric line engagement.Item Аналіз гідродинамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса(КНТУ, 2016) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Руденко, Т. В.; Красота, М. В.; Kuleshkov, Y.; Mahonets, E.; Kuleshkova, K.; Rudenko, T.; Krasota, M.В статті наведені результати аналізу впливу динамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса на його працездатність. Зазначені умови виникнення компресії і декомпресії робочої рідини у відсіченій порожнині шестеренного насоса. Встановлено взаємозв’язок між компресією і декомпресією робочої рідини, що виникають у відсіченій порожнині шестеренного насоса і негативним впливом цих явищ на працездатність насоса. Зазначено зниження працездатності шестеренного насоса внаслідок негативного впливу гідродинамічних явищ у відсіченій порожнині, що виявляється у підвищеному зношуванні деталей і з’єднань насоса, зниженні довговічності, коефіцієнту подачі, підвищенні пульсації тиску і подачі, збільшенні вібрацій і шуму НШ. The objective of the work is to analyse scientific and technical information and to determine further directions of research of processes taking place in the isolated section of a gear pump and to formulate scientific hypothesis of the research. The article presents the analysis results of the influence of dynamic processes taking place in the isolated section of a gear pump on its operational performance. The conditions of the occurrence of compression and decompression of hydraulic oil in the isolated section of a gear pump were determined. The interrelationship between the compression and decompression of the hydraulic oil which occurs in the isolated section of a gear pump and the negative influence of these effects on the operational performance of a pump was established. The decrease of operational performance of a gear pump is resulted by the negative influence of hydrodynamic effects in the isolated section. This results the excessive wear of the pump parts and interferences, decrease of service life, pump delivery rate and increase of pressure and delivery pulsation, vibration and noise of the gear pump. It was determined that scientific and technical information does not have physical and mathematic models with the description of hydrodynamic processes taking place in the isolated section of a gear pump. On the basis of the analysis of scientific and technical information we suggested a working hypothesis of the research with the result to exclude the gaps in theory and practice of a gear pump concerning hydrodynamic processes taking place in the isolated section of a gear pump.