Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
7 results
Search Results
Item Залежність структури електродугових покриттів від параметрів напилення деталей транспортної техніки(ЦНТУ, 2023) Студент, М. М.; Маркович, С. І.; Задорожна, Х. Р.; Гвоздецький, В. М.; Student, М.; Markovych, S.; Zadopozna, K.; Hvozdetskii, V.Досліджено умови плавлення та структуру покриттів, напилених методом електродугового напилення залежно від тиску повітряного струменю. Показано, що збільшення тиску металоповітряного потоку від 0,6 до 1,2 МПа підвищує швидкість струменю від 300 до 600 м/с, при цьому дисперговані краплини досягають швидкості від 120 до 220 м/с. Відповідно це викликає зменшення товщини ламелей електродугового покриття, а також сприяє формуванню підвищеної кількості оксидної фази на поверхні ламелей. Це збільшує мікротвердість покриття із У8 із 350-400 HV за тиску 0,6 МПа. до 450...500 HV за тиску 1,2 МПа. Мікротвердість покриттів із 90Х17Р3ГС зростає від 600 до 740 HV. The use of special flux-cored wires for electric arc spraying allows for coatings with high wear resistance. However, the insufficient adhesion and cohesion of the resulting coatings does not allow these coatings to be used under increased operating loads. To improve the mechanical characteristics of gas-thermal coatings, a supersonic gas jet is used to transport molten droplets to the sprayed surface, increasing their kinetic energy. It is proposed to apply a supersonic air jet using a Laval nozzle and increasing the air jet pressure from 0.6 to 1.0...1.2 MPa. The aim of the study is to determine the effect of air jet pressure on the structure of electric arc coatings.Item Дослідження впливу температури електроліту при імпульсному анодуванні на властивості поверхневих шарів технічного алюмінію(ЦНТУ, 2023) Гвоздецький, В. М.; Маркович, С. І.; Задорожна, Х. Р.; Студент, М. М.; Hvozdetskii, V.; Markovych, S.; Zadorozhna, К.; Student, М.Імпульсне анодування формує оксидні шари на алюмінієвих сплавах, що дозволяє отримати поверхневі шари з високою твердістю (до 2000 HV), низьким коефіцієнтом тертя, високою адгезією до металевої основи та низькою екологічною небезпекою. Проведено дослідження впливу температури імпульсного анодування на структуру та зносостійкість анодованих шарів. Встановлено, шо більше молекул води та сірки в анодованому шарі, то менша його мікротвердість та абразивна зносостійкість. Мінімальний знос анодованого шару, а значить найвищу його зносостійкість, зафіксовано для шарів, синтезованих за температури анодування -8ºС, а максимальний знос та найменшу зносостійкість за температури анодування -5ºС. Висока зносостійкість анодованих шарів, синтезованих за температур електроліту від -8 до +10ºС за умов тертя без мащення зумовлена наявністю кристалічної води в анодованому шарі. luminum alloys are characterized by low abrasive wear resistance, which significantly restricts their wide use in technological environments, especially if they contain abrasive particles. The method of pulse anodizing, which consists in periodically changing the current density, allows to improve the hardness and abrasive wear resistance. However, the influence of temperature on these processes has not been sufficiently studied.Item Вплив складу шихти порошкових дротів на механічні властивості та корозійну стійкість електродугових покриттів(ЦНТУ, 2023) Студент, М. М.; Маркович, С. І.; Гвоздецький, В. М.; Задорожна, Х. Р.; Student, М.; Markovych, S.; Hvozdetskii, V.; Zadopozna, К.Досліджено механічні властивості, хімічну мікрогетерогенність та корозійну стійкість у 3% водному розчині NaCl електродугових покриттів з порошкових дротів (ПД) залежно від компонентного складу шихти, використаного під час їх виготовлення. Показано, що покриттям з ПД властива висока неоднорідність за хімічним складом, що відрізняє їх від покриттів, отриманих розпилюванням суцільних дротів. Адже подрібнені повітряним струменем краплини розплаву ПД, що формують покриття, суттєво різняться за хімічним складом. Такий градієнт спричинений неповним розплавленням і змішуванням складників шихти та сталевої оболонки в дузі між торцями ПД під час електродугового напилювання покриттів. Запропоновано додавати до складу шихти ПД порошки, які забезпечили би в краплинах розплаву ПД необхідну кількість хрому, бору, вуглецю. А саме, додавання до шихти ПД порошків ферохрому (ФХ), карбіду бору (B4C), ферохромбору (ФХБ), феросплавів (FeSi, FeMn) та самофлюсу ПГ10Н-01 дало змогу підвищити гомогенність розплаву ПД та активізувати утворення евтектик між складниками шихти ПД 90Х17РГС та ПД 90Х17Р3ГС. Завдяки цьому добились нижчої хімічної мікрогетерогенності отриманих покриттів та забезпечили їм високу корозійну тривкість, близьку до корозійної тривкості нержавіюча сталі Х18Н9Т. Electric arc spraying of coatings is common in many branches of industrial production, in particular to restore the geometry of machine parts worn in operational conditions, to increase their protection against abrasive and gas-abrasive wear (at the same time, both at climatic and at technologically determined elevated temperatures). Coatings sprayed using powdered wires are characterized by high chemical heterogeneity, which significantly distinguishes them from electric arc coatings made of solid wires. This is due to the different chemical composition of the droplets formed from the molten powder wires and carried by the air jet to the surface of the substrate, forming a coating on it. The charge with alloying elements in its composition (including difficult-to-melt ones such as FH, B4C, FHB) does not have time to fully melt and mix with the melt of the steel shell. It is clear that because of this, the melt droplets of flux-cored wires dispersed by an air jet will have a different chemical composition and , as a result, the coatings formed from these droplets on the surface of the substrate will be characterized by high heterogeneity and significant chemical heterogeneity, which will affect their physical and mechanical properties at different operating temperatures and especially when exposed to corrosive environments.Item Трибологічна поведінка ПЕО шарів у парі зі сталями 45 та У 8(ЦНТУ, 2017) Студент, М. М.; Сірак, Я. Я.; Маркович, С. І.; Student, М.; Sirak, Y.; Markovich, S.Досліджено трибологічну поведінку сталей 45 та У8 у парі із ПЕО шарами, синтезованими на легких сплавах АМг-6 та Д16Т у мінеральній оливі І-20, із додатком до неї дистильованої води та водного розчину гліцерину. Виявили різницю у фрикційній поведінці ПЕО шарів, синтезованих на алюмінієвих сплавах із підвищеним вмістом магнію (АМг-6) та з підвищеним вмістом міді (Д16Т) за контактування із стальними контртілами. Purpose of this work to probe the tribologichnu conduct of PEO glowed, synthesized on the easy alloys of AMg-6 and D16T in the clean mineral olive of I-20, with an appendix to it of the distilled water and water solution of glycerin at a contact from stalyami 45 and U8 . The tribological behavior of steels 45 and Y8 in pairs with PEO layers synthesized on light alloys AMg-6 and D16T in mineral oil I-20 with the application of distilled water and an aqueous solution of glycerin was investigated. They found a difference in the frictional behavior of plasma-electrolyte layers synthesized on aluminum alloys with increased magnesium content (AMg-6) and with an increased copper content (D16T) in contact with steel counterweights. In the case of contact between the plasma-electrolyte layers synthesized on the AMg-6 alloy with the steels under investigation, as a result of tribochemical reactions in the contact zone on the steel surface, a spinel-type oxide layer is synthesized with the general formula FeAl2O4, which protects them from wear by exposure to hydrogen, Loads not exceeding 4 MPa. In the case of contact between the plasma-electrolyte layers synthesized on the D16T alloy, oxygen-free wear of steel counter-bodies occurs and such a contact pair is operable to loads above 10 MPa with a low frictional heating temperature. Investigational tribological behavior of pair of dielectrics – an explorer (ceramics are a metal) glowed on the example of PEO, synthesized on the easy alloys of AMg and D16T in a contact with iron-carbon alloys – steel 45, U8.Item Вплив підвищеного тиску повітряного струменю на структуру і властивості електродугових покриттів(КНТУ, 2016) Студент, М. М.; Гвоздецький, В. М.; Маркович, С. І.; Student, М.; Hvozdetskyi, V.; Markovich, S.В статті наведено результати дослідження впливу тиску повітряного струменю на властивості покриттів. Встановлено, що збільшення тиску повітряного струменю від 0,6 до 1,2 МПа забезпечує зростання швидкості повітряного струменю від 300 до 600 м/с, а швидкість диспергованих краплин від 120 до 220 м/с. Підвищення тиску повітряного струменю від 0,6 до 1,2 МПа зумовлює зменшення товщини ламелей покриття, формування більшої кількості оксидної фази у покритті, при цьому зростає твердість, когезивна міцність та знижується рівень колових залишкових напружень першого роду у покритті. The aim is to investigate the effect of increasing the airspeed of molten drops during spraying coating. The article presents the results of research impact pressure air jet on the properties of coatings. It was established that increasing pressure air jet from 0.6 to 1.2 MPa, the growth speed air jet from 300 to 600 m / s, and shvydkistы dispersed droplets from 120 to 220 m / s. Increasing pressure air jet from 0.6 to 1.2 MPa causes thinning lamella coatings, forming more oxide phase in the coating, thus increasing strength, cohesive strength, and reduced levels of residual stresses circular first kind.Item Вплив складу шихти порошкових дротів на механічні властивості електродугових покриттів(КНТУ, 2012) Похмурський, В. І.; Студент, М. М.; Гвоздецький, В. М.; Ступницький, Т. Р.; Мажейка, О. Й.; Маркович, С. І.; Pokhmurskiy, V.; Student, М.; Gvozdeckiy, V.; Stupnickiy, T.; Mazheyka, O.; Markovich, S.В статті досліджено залежність механічних характеристик електродугових покриттів від сомо організаційних процесів, що відбуваються при їх формуванні під впливом елементного складу шихти порошкових дротів. The results of research of dependence of mechanical properties of elektrometal coverage are resulted from processes which take a place at their forming under act of element composition of powder-like wires.Item Вплив поруватості на трибологічні характеристики електродугових покриттів з порошкових дротів(КНТУ, 2014) Студент, М. М.; Ступницький, Т. Р.; Гвоздецький, В. М.; Маркович, С. І.; Мажейка, О. Й.; Student, М.; Stupnickiy, Т.; Gvozdeckiy, V.; Markovich, S.; Mazheyka, А.В статті досліджено вплив поруватості на трибологічні та механічні характеристики еллектродугових покриттів. Визначено, що структурою покриття з порошкових дротів є композит, де чергуються металеві ламелі та ламелі із оксидів, а також пори. Із ростом тиску повітряного струменю розмір структурних складових поверхні покриття та розмір пор зменшується. Встановлено позитивний вплив поруватості на трибологічні характеристики покриттів при терті за граничного мащення. Influence of porosity is investigational the article on mechanical properties of arc coatings. Exposed to research of coatings from different types powder-like. A structure, phase composition, porosity, resistance to the friction, cohesion of coatings depending on pressure of transporting gas, was studied. Determination of coefficient friction of coatings is exposed to research in the conditions of dry friction and border greasing It is set, that from powder-like wires the structure of coatings there is a compo, where metallic lamels and lamels alternate from oxides and also pore. With growth of pressure of air-blast the size of structural constituents of surface of coatings and size of pores diminishes. Positive influence of porosity is set on mechanical properties of coatings in the conditions of border friction. Аrc coatings of gradient type provide high mechanical properties of coatings at to the low level of remaining tensions of in them.