Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
5 results
Search Results
Item Визначення оптимальної точки приєднання сонячної електростанції до електричної мережі методом комп’ютерного імітаційного моделювання(ЦНТУ, 2023) Плєшков, П. Г.; Зінзура, В. В.; Плєшков, С. П.; Солдатенко, В. П.; Plieshkov, Р.; Zinzura, V.; Plieshkov, S.; Soldatenko, V.Метою даного дослідження є мінімізація негативного впливу сонячної електростанції на значення усталеного відхилення напруги та рівень втрат електроенергії шляхом визначення оптимального місця її приєднання до розподільної електричної мережі. В роботі для вирішення задачі оптимального розміщення відновлюваних джерел електроенергії в електричних мережах пропонується застосовувати метод комп’ютерного імітаційного моделювання. Розроблені комп’ютерні імітаційні моделі розподільної електричної мережі з сонячною електростанцією, які дали змогу визначити оптимальне місце приєднання сонячної електростанції виходячи із значень величини втрат потужності в елементах електричної мережі на рівень усталеного відхилення напруги. Результати комп’ютерного моделювання електричної мережі з сонячною електростанцією підтвердили необхідність врахування не лише значень усталеного відхилення напруги, але і величини втрат електричної енергії в елементах мережі в процесі вибору місця встановлення сонячної електростанції. The purpose of this study is to minimize the negative impact of the solar power plant on the value of the steady voltage deviation and the level of electricity losses by determining the optimal place for its connection to the distribution network. Currently, quite a large number of methods of optimal placement of renewable sources of electricity in electrical networks have been developed. However, most of them either do not fully take into account the multifunctional influence of renewable energy sources on the parameters of the electric network regime, or are quite difficult to use. In order to solve the problem of optimal placement of renewable sources of electricity in electric networks, it is proposed to use the method of computer simulation modeling. The essence of this method is to determine the optimal place for connecting a renewable energy source to the electrical network based on the analysis of the results of computer simulation modeling of network mode parameters. This approach is the most acceptable in the case of connecting a solar power plant of average power to the electrical network of an industrial enterprise. The developed computer simulation model of a distribution electric network with a solar power plant allows for the research of network mode parameters, including the determination of the level of active power loss in network elements and the level of steady voltage deviation. The specified computer simulation models of the distribution electric network with a solar power plant made it possible to determine the optimal place for connecting the solar power plant based on the values of power losses in the elements of the electric network at the level of the established voltage deviation.Item Комп’ютерне моделювання процесу прямого пресування через різні профілі матричних лійок(ЦНТУ, 2020) Свяцький, В. В.; Скрипник, О. В.; Конончук, С. В.; Sviatskyi, V.; Skrypnyk, O.; Kononchuk, S.; Свяцкий, В. В.Виходячи з аналізу напруженого і деформованого стану стадії пресування, що встановилася, запропоновано використовувати профіль матричної лійки, виконаний по лінії ковзання, що розділяє пружну і пластичну зону. Результати теоретичних досліджень, комп’ютерного моделювання процесу прямого пресування за допомогою програмного комплексу Deform 2D/3D, експериментальних дослідів показали, що кращі умови пресування досягаються через матрицю із профілем, який виконаний по лінії ковзання. The stressed and deformed state of the metal and the dimensions of the center of deformation during pressing depend significantly on the design of the tool and, in particular, on the shape of the matrix funnel. However, there is still no single point of view on the influence of the geometry of the deformation center on the energy forces of the metal pressing process. Based on the analysis of the field of slip lines of the steady-state stage of pressing through a symmetric single-point matrix, it is proposed to use the profile of the matrix funnel made along the slip line separating the elastic and plastic zones. The following types of matrix funnel profiles were investigated using computer simulation of direct extrusion of lead samples with a drawing value 81 at a speed of 1 mm/s: cycloid concave; convex; the second convex, which is built on the logarithmic dependence; conical and concave, which is built along a sliding line that separates the elastic zones from the plastic in the pressing process. The results of theoretical studies, computer simulations of the direct pressing process using the Deform 2D/3D software package, and experimental experiments have shown that optimal energy-power conditions are achieved by pressing through a matrix that has a profile made along the slip line. The results of the experimental study of the kinetics of the flow of the discrete medium showed that the shape of the matrix funnel influences the size of the deformation center and the distribution of the resulting deformation in the molding. From the analysis of deformation of the granules, it is determined that the concave funnel, built along the slip line, is characterized by a curvature of the axisymmetric particles in the direction of deformation. These curvatures decrease as the granules move to the axis of symmetry of the matrix. It is noted that for a convex funnel, the length of the deformation center is greatest; for a conical metal flow is close to the radial in the direction of the truncated cones. На основе анализа поля линий скольжения установившейся стадии прессования через симметричную одноочковую матрицу предложено использовать профиль матричной воронки, выполненный по линии скольжения, разделяющий упругую и пластическую зону. Результаты теоретических исследований, компьютерного моделирования процесса прямого прессования с помощью программного комплекса Deform 2D/3D, экспериментальных опытов показали, что оптимальные энергосиловые условия достигаются при прессовании через матрицу, которая имеет профиль, выполненный по линии скольжения.Item 3D модель для исследования динамики центробежной соковыжималки с шаровым автобалансиром(КНТУ, 2013) Гончаров, В. В.; Филимонихин, Г. Б.; Гончаров, В. В.; Філімоніхін, Г. Б.; Goncharov, Valeriy; Filimonikhin, GennadyСоздана 3D модель центробежной соковыжималки с цилиндрическим ситом и шаровым автобалансиром для ее уравновешивания на ходу в САПР SolidWorks. С использованием модуля Cosmos Motion проведена обработка, наладка и тестирование модели. Модель предназначена для исследования динамики машины, проведения виртуальных многофакторных экспериментов. Створена 3D модель відцентрової соковижималки з циліндричним ситом і кульовим автобалансиром для її зрівноваження на ходу в САПР SolidWorks. З використанням модуля Cosmos Motion проведено обробку, налагодження і тестування моделі. Модель призначена для дослідження динаміки машини, проведення віртуальних багатофакторних експериментів. In the process of work of electric centrifugal juicers (juicers) with the cylindrical sieve the pulp is distributed non-uniformly on a sieve which causing a significant imbalance and vibration of machine case. To balance these juicers on the go in the operation the authors propose their modernization which consists in replacing the standard platform for mounting the sieve by platform combined with ball auto-balancer. In order to study the process of balancing by auto-balancer of juicer’s cylindrical sieve created its 3D model with using the CAD system SolidWorks and its module Cosmos Motion. The simulation was performed in a technique that can be adopted as the standard for modeling process-balancing in rotor systems. It includes the steps of: 1) creation of models of details of a juicer in SolidWorks; 2) union of details in assembly; 3) kinematic and power processing of assembly by the Cosmos Motion module; 4) choice of criteria of quality of operation of the auto-balancer and juicer (the value of the module of residual acceleration of the case, time of onset of auto-balancing etc.); 5) adjustment of the model (the values of its parameters are selected in maximum accordance with the real machine); 6) the choice of model parameters; 7) test of the model of elementary tasks, the results of which are known or can be easily interpreted. The model of a juicer created by the offered technique is efficient and provides high speed of calculations. Its key parameters correspond to a natural juicer with the ball-type auto-balancer. By means of the created model it is possible to make fully - factorial and multiple-factorial experiments, in particular – with 2-levels, 3-levels, for search of optimum values of parameters of a juicer with the auto-balancer.Item Комп’ютерна модель процесу автоматичного динамічного зрівноваження двома автобалансирами крильчатки осьового вентилятора(КНТУ, 2013) Олійниченко, Л. С.; Філімоніхін, Г. Б.; Olijnichenko, Lubov; Filimonikhin, GennadyУ САПР SolidWorks модернізовано 3D модель осьового вентилятора з автобалансиром у обтічнику встановленням другого автобалансира на хвостовик вала електродвигуна. Із використанням модуля Cosmos Motion проведено обробку, налагодження і тестування моделі. Модернізована 3D модель призначена для комп’ютерного моделювання процесу динамічного зрівноваження крильчатки з ротором електродвигуна двома автобалансирами. We study the process of dynamic balancing of the axial fan impeller by two ball auto-balancers whis using SolidWorks CAD software and its module Cosmos Motion. For this were upgraded computer model of an axial fan with ball auto-balancer in the radome of fan by installing a second auto-balancer on a shaft of the engine. Thus with the help of CAD SolidWorks were created the parts of second auto-balancer and added to the assembly. With the module Cosmos Motion were set kinematic relations and interaction force between the parts of the new auto-balance. Debugging and testing of a computer model was conducted of elementary problems whose solutions are known and the simulation results are easily interpreted. As a result the resulting model is the computer analog of the full-scale stand with the same characteristics. It is suitable for the virtual multi- factorial and full- factorial experiments to select the optimal parameter values of fan and auto-balancers. With using of the created model were investigated the effect of gravity and the parameters of an imbalance in the auto-balancing process.Item Комп'ютерне моделювання полів температур та напружень в композиційних матеріалах та покриттях при їх формуванні, терті та зношуванні(КНТУ, 2014) Аулін, В. В.; Бобрицький, В. М.; Aulin, Viktor; Bobrytskyi, VitaliiВ статті за допомогою комп’ютерного моделювання досліджено поле температур та напружено- деформований стан композиційних матеріалів та покриттів на всіх етапах їх життєвого циклу. Визначено розподіл нестаціонарних полів температур та напружень, які виникають в композиційних матеріалах та покриттях в процесі їх формування і тертя та зношування, а також локальні області з максимальною різницею перепаду температур і напружень та вплив на них внутрішніх і зовнішніх факторів. Виявлено тісний взаємозв'язок між складом композиційних матеріалів і покриттів, розмірами і формою їх структурних складових та статистичними і локальними значеннями досліджуваних полів температур і напружень відповідних нестаціонарних полів. Результати комп’ютерного моделювання дають можливість оптимізувати склад та структуру композиційних матеріалів та покриттів для підвищення їх фізико-механічних та триботехнічних характеристик і властивостей. The article by computer simulation investigated the distribution of temperature and stress-strain state of composite materials and coatings at all stages of their life cycle. Determined the distribution of transient temperature fields, stresses and strains that occur in composite materials and coatings in the process of forming and friction and wear , as well as local areas with a maximum difference of temperature and stress and the impact on their internal and external factors. Computer simulation of composite materials and composite coatings made it possible to construct a non-stationary heat field and thermal stress field in composite materials and composite coatings with dispersion - strengthened and eutectic types of structures that arise from stationary sources of heat ( of friction ). It is shown that the configuration of these fields are essentially uniform, there are significant changes in temperature and stress due to heterogeneity of structure heterogeneity thermophysical and mechanical properties of the structural components of composite materials and composite coatings that achieve , depending on the load of friction , melting components, and local stress - up to several GPa. The value of tensile stress and compressive alternating throughout the volume of the composite material and composite coatings. There is a close relationship between the structure of composite materials and composite coatings, the size and shape of structural components and statistical and local values of temperature and stress appropriate nonstationary fields. To minimize temperature changes and thermal stresses to use uniform size structure of the filler with a maximum dispersion of carbides and align the thermal properties of filler and matrix, which must provide high relaxation ability. According to the results of computer simulation can optimize the composition and structure of composite materials and coatings to enhance their physical and mechanical characteristics and tribotechnical.