Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
6 results
Search Results
Item Экспериментальные исследования транспортирования семян к заделывающим органам(ЦНТУ, 2017) Сербин, В. И.; Мельник, Ю. В.; Лысый, Р. Ф.; Сербін, В. І.; Лисий, Р. Ф.; Serbin, V.; Melnik, Yu.; Lysyiy, R.В статье изложены результаты экспериментальных исследований транспортирования семян по вращающимся семяпроводам, при которых обеспечивается качественное выполнение технологического процесса посева пропашных культур на скоростях движения посевного агрегата до 13, 26 км/ч. У статті викладені результати експериментальних досліджень транспортування насіння по обертовим насінняпроводам, при яких забезпечується якісне виконання технологічного процесу посіву просапних культур на швидкостях руху посівного агрегату до 13, 26 км/год. One of the reasons leading to a violation of the normal functioning of the rotational-hole drill process is the large duration of the seed movement on the seed ducts. As the seed drill speed increases, there is an emission of seeds to the surface of the soil, due to the delay in the supply of seeds to the lobes. Therefore, in order to make a reasonable choice of the operating modes of the seeder and to properly manage them, it is necessary to have data on the regularities of the movement of seeds by seed lines. In order to verify the theoretical premises for the transportation of seeds, a series of experiments was carried out to determine the reliability of the basic provisions of the analytical model of seed movement by seed ducts. The experiments were conducted on a laboratory plant with the connection of a source of compressed air to it. The pressure in the pressure chamber of the sowing machine was determined and controlled by a liquid manometer. The air jet velocity corresponding to each of the controlled pressures was calculated from the dynamic pressure measured with the Prandtl tube. The experiments used standard seeds whose sailing coefficient did not exceed 0.1 m-1. A regressive model is obtained that characterizes the effect of air pressure and the angular velocity of the wheel (seeder speed) on the angle of ejection of seeds from the seed tube. At the same time, the following regularities have been experimentally confirmed: large air pressure is required for the drill to work at high speeds. For operation at speeds of 2.00...3.60 m/s (7.0...13.26 km/h), the air pressure is required to be 1.00 ... 3.00 kPa. The unevenness of dispersion of the ejection angles in experiments was revealed. With the increase in the angular velocity of the wheel and the decrease in the air pressure, the dissection angle of the ejection increases markedly, reaching the magnitude unacceptable for practice at extreme levels. It is shown that the limiting dispersion characterizing the dispersion of the ejection angle of seeds can be expressed in numbers 7 ... 8. The regression equation is used to determine the seed rate at the outlet, depending on the air pressure and the circumferential velocity of the wheel, which satisfies the requirements of the seed processor process, the seed rate at the outlet does not exceed 7 m/s, which is less than the rate causing the seed trauma.Item Модель динаміки маятникового акселерометру при випадковому вхідному сигналі(КНТУ, 2006) Осадчий, С. І.; Босько, В. В.; Дідик, О. К.Стаття присвячена розробці методики ідентифікації та оцінюванню передаточної функції маятникового акселерометру та спектральної щільності його власних шумів. Clause devoted to development of a technique of identification that akcelerometr of transfer function that of spectral density of own noise.Item Підвищення енергетичної ефективності обробки деревини за рахунок оптимального управління приводом подачі(КНТУ, 2008) Осадчий, С. І.; Гамалій, В. Ф.; Шаповалова, І. А.В статті подано структуру оптимальної системи стохастичної стабілізації потужності різання для деревообробного верстату та здійснено аналіз її точності. The article contains the analysis of accuracy of the optimum and existing system of stabilization of the power of cutting for woodworking machine-tool.Item Швидкість руху агрегату і висота брання льону-довгунця як фактори якості очісування стебел комбайном(КНТУ, 2010) Лімонт, А. С.; Limont, A.Розглянуто втрати насіння від недоочісування стебел залежно від швидкості руху льонозбирального комбайнового агрегату та висоти брання льону-довгунця. Вплив досліджуваних факторів на якість очісування визначений з використанням елементів дисперсійного аналізу. The paper considers loss of seeds by stalk under stripping mess depending on flax combine unit travel speed and fiber flax pulling height. The influence of the factors under study on the stripping quality has been determined using some elements of dispersion analysis.Item Дослідження функцій температури молока для автоматичної діагностики еструс-періоду у тварин(КНТУ, 2011) Версаль, В. О.; Версаль, Ю. В.; Богданова, А. О.; Versal, V.; Versal, J.; Bohdanova, А.В статті описано дослідження випадкових функцій ранішньої та вечірньої температури молока корів, а саме: проведено їх реєстрацію та обробку даних. Обробка включала знаходження оцінок для математичних очікувань, дисперсій та середньоквадратичних відхилень функцій. Досліджено функції відхилень ранішньої та вечірньої температури молока тварин від попередніх значень за різницю часу 1…3 дні. Доведено, що найкраща стратегія діагностики еструс-періоду – якщо відхилення значення ранішньої температури молока від середнього за три попередні дні ≥0,2 °С, вечірньої - ≥0,5 °С. In article the reseaches of random a.m. and p.m. cows’ milk temperature’s functions are described, viz their registration and data processind were carried out. The processing was consisted from finding of estimations for mathematical expectations, dispersions and standard deviations of functions. The functions of deviations of a.m. and p.m. animals’ milk temperature from previous values at the time difference of 1…3 days are researched. It’s proved, that the best strategy of estrus diagnostics is if the deviation of a.m. and p.m. milk temperature values from the mean one for three previous days ≥0,2 °С, p.m. - ≥0,5 °С.Item Оцінювання висоти дисперсного матеріалу при неповних вимірюваннях вихідних сигналів зерносушильної установки (ЗСУ) з киплячим шаром(КНТУ, 2010) Шмельова, Т. Ф.; Калита, М. О.; Скриннік, І. О.; Шалімов, В. О.; Shmelyva, T.; Kalita, M.; Skrynnik, І.; Shalimov, V.В статті вперше запропоновано методику визначення оцінки зміни висоти киплячого шару дисперсного матеріалу непрямим способом безпосередньо в камері сушіння та проаналізовано вплив співвідношень вихідних сигналів та завади системи вимірювання. In the article the method of determination of estimation of height of boiling layer of dispersible material is first offered by an indirect method in a drying chamber. Having connection of height of boiling layer on all of cascades between itself, it is possible to get the estimation of height material on each of cascades at any moment to time.