Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
10 results
Search Results
Item Оптимізація точності прогнозування співвідношення руда/вода в кульовому млині з циркулюючим навантаженням(КНТУ, 2016) Кондратець, В. О.; Сербул, О. М.; Kondratets, Vasily; Serbul, AlexanderВибір пристроїв вимірювання технологічних параметрів за похибкою можливо подати як задачу оптимізації відповідно методу динамічного програмування у три стадії, у кожній з яких обирається один з засобів. В процесі оптимізації при відносній похибці вимірювання витрати пульпи у пісковому жолобі ±3,0 % відносна максимальна похибка прогнозування співвідношення руда/вода склала 1,72 % при визначенні витрати руди і води в млин з похибкою ±1,0 % порівняно з допустимою ±3,0 %. The purpose of the article is a search for the best combination of precision instruments for the margin of error prediction liquefaction. The ratio of the ore/water predict possible in accordance with this algorithm on the measured parameters - ore and water consumption in a ball mill, a volume flow of ore and water in a ball mill, a volume flow of sand in sand classifier chute. The measurement error of each parameter introduces an error in the final result. he task is complicated by the fact that the volumetric flow of sand in the sand chute accurately measure is not possible, which significantly reduces the result of forecasting where the measurement error or most approximates the boundary permissible value of ± 3,0% for the ratio of ore/water. Selection device for measuring process parameters of error may be represented as the optimization problem by the method of dynamic programming in three stages, each of which selects one means. In the process of optimizing the relative error of flow measurement in sand chute ± 3,0%, the maximum relative error of prediction ratio of ore / water amounted to 1.72% as determined by the flow of ore and water in the mill with an accuracy of ± 1,0% compared with the allowable ± 3 0%.Item Дослідження перемішування матеріалів у кульовому млині як багатовимірному керованому об’єкті(КНТУ, 2016) Кондратець, В. О.; Мацуй, А. М.; Kondratets, Vasily; Matsui, AnatoliiВстановлено, що осереднення твердого у кульовому млині відбувається достатньо швидко, практично за 34 с. Більш проблематичним є перемішування твердого з водою. Запропоновано воду у кульовий млин до необхідного розрідження пульпи подавати трьома потоками – на поверхню вихідної руди, у приймальний пристрій завиткового живильника до граничного розрідження пісків класифікатора та безпосередньо у горловину кульового млина, розбризкуючи її в широкій зоні завантаження. The aim of work is to study the mixing of materials along the drum of the ball mill, which works in a closed circuit with mechanical single- qualifier for its improvement. The ball mill as a multidimensional object has four output value. In this article a study performed on one of them - the parameter of the mixing materials, which is characterized, on the one hand, averaging the size of the solid, on the other hand, by mixing the solid with water. It is found that the averaging of the solid is not very dependents on its shape and size, in ball mill it happens sufficiently rapidly for 34 seconds, practically continuously improving the performance for a given time interval. More problematic is the mixing of the solid and water, which under the existing conditions is carried on a length of 1/4 ... 1/3 mill drum and which in consequence, does not actively participate in the grinding of the ore. Proposed that the water in a ball mill should be fed to the required dilution of the pulp by the three streams - to the surface of the original ore, the receiver cochlear feeder to the classifier boundary liquefaction sand directly into the throat of a production unit, spraying it into a wide area load. The proposed approach supplying water into a ball mill provides inclusion 1/4 ... 1/3 the length of the drum in efficient crushing of ore, which greatly improves the performance of his work.Item Дослідження кульового млина як керованого об’єкта по каналу продуктивності(КНТУ, 2008) Кондратець, В. О.; Рева, О. М.; Карчевська, М. О.Приведені результати розробки моделі кульового млина як керованого об’єкта по каналу продуктивності по готовому продукту. Показана можливість керування подрібненням з використанням вихідного живлення, циркулюючого навантаження, розрідженості пульпи та споживаної потужності. Для здійснення такого керування необхідно розробити засіб ідентифікації завантаження кульового млина рудою та підхід автоматичного формування й підтримання бажаної характеристики крупності кульового навантаження. Results of development of model of a spherical mill as controlled object on the channel of productivity on a ready product are resulted. The opportunity of management by crushing with use of the initial meal, circulating loading, dilution pulps and is shown power consumption. For realization of such management it is necessary to develop means of identification of loading of a spherical mill ore and the approach of automatic formation and maintenance of the required characteristic to the largeness spherical loading.Item Дослідження кульового млина, що подрібнює піски класифікатора, по каналу розрідження пульпи(КНТУ, 2008) Кондратець, В. О.; Мацуй, А. М.В статті приведені результати дослідження кульового млина, що подрібнює піски класифікатора, по каналу розрідження пульпи. Показано, що похибка ідентифікації співвідношення руда/вода не приводить при регулюванні до зміни режиму агрегату. Не допустимо в якості керуючого діяння використовувати зміну витрати води, яка подається безпосередньо у кульовий млин. In the article the results of research of ball mill, grinding down sands of classifier are resulted in the article, on the channel of dilution of mash. It is rotined that error of authentication of correlation ore/water does not lead at adjusting to the change of the mode of aggregate. It is not possible as managing influence to utillize the change of rate-of-flow, which is given directly in a ball mill.Item Теоретичне дослідження стохастичної САР розрідження пульпи в кульовому млині з циркулюючим навантаженням(КНТУ, 2008) Кондратець, В. О.; Рева, О. М.; Сербул, О. М.У статті приведені результати теоретичних досліджень стохастичної САР розрідження пульпи у кульових млинах з циркулюючим навантаженням. Показано, що забезпечити необхідну точність визначення співвідношення руда/вода на вході кульового млина можливо лише фільтрацією випадкових сигналів витратоміра пульпи у пісковому жолобі класифікатора та вихідної руди перед подачею на вхід блока ідентифікації даного технологічного параметра. In article are brought results of the theoretical researches stochastic SAR dilutions of the pulp in ball mill with circulating load. It is shown that to provide necessary accuracy of the determination the correlation ore/water at the input ball mill possible only filtering casual signal device of consumption pulps in sand chute qualifier and source ore before presenting on entering the block of identifications this technological parameter.Item Дослідження нелінійної системи автоматичного управління подачею води у кульовий млин, що подрібнює піски класифікатора(КНТУ, 2013) Мацуй, А. М.; Кондратець, В. О.; Matsui, A.; Kondratets, V.Обґрунтована функціональна схема системи автоматичного управління подачею доданої води у кульовий млин, що подрібнює піски двоспірального класифікатора, та її складові елементи. Показано, що вона повинна містити обчислювальний блок, який формує змінне задаюче діяння на витрату доданої води, та ідеалізований елемент, що спрацьовує при занадто низьких рівнях вхідного сигналу і має характеристику без гістерезису. The aim is to study the automatic control system of water supply in a ball mill that grinds the sand classifier. It is shown that the stabilization of dilution of the pulp in a ball mill, which grinds sands double-qualifier is necessary to organize an incomplete invariant ratio control solid / liquid in the receiver cochlear feeder and final input to the ball mill feed into the neck of a small amount of water. Proposed a non-linear system of automatic control supply of water added to the ball mill containing idealized relay element and a computer unit, which in terms of the pulp and the actual ratio of solid / liquid in the receiver cochlear feeder, set ratio solid / liquid and the density of the ore forming variable sets the effect on water consumption. Idealized relay element and computing unit implemented in the controller. Idealized relay element operates at extremely low levels of the input signal and has the feature without hysteresis. The proposed automatic control system is stable and has high quality.Item Теоретичне дослідження усталених і перехідних режимів роботи куль та футеровки в млинах(КНТУ, 2008) Кондратець, В. О.; Рева, О. М.; Карчевська, М. О.У статті приведені результати теоретичних досліджень усталених і перехідних режимів роботи куль та футеровки у млинах. Встановлені оптимальні умови роботи млина та ідентифікації його завантаження рудою. In the article the results of theoretical researches of the set and transitional modes of operations of balls and lining-up are resulted in mills. The optimum terms of work of mill and authentication of its load ore are set.Item Теоретичне дослідження взаємодії первинних перетворювачів завантаження кульового млина рудою з молольними тілами(КНТУ, 2010) Кондратець, В. О.; Карчевська, М. О.; Kondratec, V.; Karchevskaya, M.У статті приведені результати дослідження взаємодії первинних перетворювачів завантаження кульового млина рудою з молольними тілами. Встановлено, що взаємодія торців первинних перетворювачів і куль є випадковим процесом. Знайдена імовірність попадання кулі в торець перетворювача, що пропорціональна відношенню куба діаметра торця перетворювача до квадрата діаметра кулі. Її ще наближено можна подати як відношення числа попадань до числа випробувань. Оцінка цієї імовірності у даних умовах показала, що надійній імовірності 0,997 відповідає інтервал 0,00021…0,00135, який, наприклад при 10000 випробувань, гарантує не менше 2 і не більше 13 попадань кулі у торець перетворювача. Певне число випробувань визначається кількістю обертів барабана млина або часом його роботи. Встановлено, що за 240 с число попадань кулі в торець основного перетворювача буде дорівнювати п’яти. За інтервал часу 960 с гарантовано відбудеться одне попадання кулі в додатковий перетворювач. Такі тимчасові інтервали цілком задовольняють практику. In the article the results of research of interaction of primary converters of loading of a spherical mill by ore with grindings bodies are given. The probability of hit of a sphere in an end face of the converter is found which is proportional to the attitude of a cube of a diameter of an end face of the converter up to a square of a diameter of a sphere. Its still approximately it is possible to submit as the attitude of number of hits to number of tests. The estimation of this probability in the given conditions has shown, that to reliable probability 0,997 there meets an interval 0,00021…0,00135, which, for example at 10000 tests, guarantees not less than 2 and no more than 13 hits of a sphere in an end face of the converter. The certain number of tests is determined by quantity of revolutions of a drum of a mill or time of its job. Is established, that for 240 about number of hits of a sphere in an end face of the basic converter will be equal to five. For an interval of time 960 with is guaranteed one hit of a sphere in the additional converter is held. Such temporary intervals completely satisfy practice.Item Обґрунтування підходу підвищення точності ідентифікації співвідношення руда/вода в кульових млинах з циркулюючим навантаженням(КНТУ, 2009) Сербул, О. М.; Кондратець, В. О.У статті приведені результати аналізу по обґрунтуванню підходу підвищення точності ідентифікації співвідношення руда/вода в кульовому млині з циркулюючим навантаженням. Доведено, що допустиму помилку ідентифікації технологічного параметра можна забезпечити оптимізацією точнісних характеристик вимірювальних засобів. In article are brought results of the analysis on motivation of approach increasing of accuracy to identifications of the correlation ore/water in ball mill with circulating load. It is proved that possible mistake to identifications of the technological parameter possible to provide at optimization an accuracy features of the measuring facilities.Item Дослідження руху молольних тіл і пульпи в барабані кульового млина з метою ідентифікації завантаження(КНТУ, 2009) Кондратець, В. О.; Карчевська, М. О.У статті приведені результати дослідження руху молольних тіл в поперечному перерізі й вздовж барабана. Виокремлена закономірність розташування та руху куль у поперечних перерізах, становлені перемішуючі властивості кульового млина. In the article the results of research of motion of grindings bodies in a transverse section and mash are resulted in a transverse section and along a drum. Conformity to law of placing and motion of balls is selected in transverse sections, mixing up properties of ball mill are set.