Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
6 results
Search Results
Item Теплообмін і тертя турбулентного потоку газу в трубі при малих числах Рейнольдса(ЦНТУ, 2017) Святецький, М. В.; Ошовський, В. Я.; Капура, І. А.; Будуров, В. Л.; Svyatetsky, M.; Oshovsky, V.; Kapura, I.; Budurov, V.В статті проаналізовані відомі результати експериментальних і теоретичних досліджень розглядуваних процесів. Загальним недоліком згадуваних робіт є відсутність належної фізичної обгрунтованості прийнятих напівемпіричних теорій, що не дозволяє достатньо коректно врахувати специфіку процесів турбулентного переносу і істотно обмежує область застосування одержаних результатів. Показано, що врахування взаємодії молекулярного і молярного механізмів переносу, які кількісно порівнянні, дає можливість узгодити експериментальні результати з теоретичними. Таким чином викладений метод дозволяє з єдиних позицій розраховувати характеристики теплообміну і гідродинаміки газового потоку в трубі в широкому діапазоні чисел Рейнольдса. The purpose of the paper is to study the features of turbulent heat and momentum transfer in round tubes at small Reynolds numbers. The article analyzes the results of experimental and theoretical studies of the processes under consideration. The general disadvantage of the above-mentioned works is the lack of proper physical validity of the accepted semi-empirical theories, which does not allow us to properly take into account the specifics of the processes of turbulent transfer and substantially limits the scope of the applicability of the results obtained. It is shown that the account of the interaction of the molecular and molar transport mechanisms which are quantitatively comparable gives the possibility to reconcile the experimental results with the theoretical. The thus expounded method allows from single positions to expect descriptions of heat exchange and hydrodynamics of gas stream in a pipe in the wide range of numbers of Reynolds.Item Моделювання процесу заморожування гарбузових овочів(КНТУ, 2013) Ялпачик, В. Ф.; Кюрчев, С. В.; Тарасенко, В. Г.; Yalpachik, Vladimir; Kyurchev, Sergey; Tarasenko, VeraРобота присвячена розробці математичної моделі процесу заморожування гарбузових овочів та її апробації по змінних в часі температурних полів, тривалості процесу і тепловим потокам шляхом порівняння розрахункових та експериментальних даних з метою контролю процесів в промислових умовах і подальшого вирішення задач енерго- та ресурсозбереження на агропромислових підприємствах.The work is devoted to developing a mathematical model of the process of freezing pumpkin vegetables and its approval by variable temperature fields over time, and duration of the heat flux by comparing the calculated and experimental data for process control in an industrial environment and further solve the problems of energy efficiency in the agro-industrial enterprises. Nonlinear interpolation formulated a mathematical model for the process of cooling and freezing pumpkin vegetables can expect changes in temperature fields and heat fluxes from the surface facilities refrigeration processing time. On the basis of testing of the formulated mathematical model obtained satisfactory results of testing.Item Стендові випробовувуння макетного зразка газогідратного акумулятора природного холоду(КНТУ, 2012) Клименко, В. В.; Корнієнко, В. Н.; Скрипник, О. В.; Klymenko, V.; Kornienko, V.; Skrypnyk, А.У статті описано конструкцію макетного зразка газогідратного акумулятора природного холоду (ГАПХ) для систем охолодження плодів і овочів з активним вентилюванням і стенд для його випробовувань. Приведено методику і результати випробовувань. Підтверджено працездатність макетного зразка в умовах, характерних для експлуатації систем охолодження плодів і овочів з активним вентилюванням. За результатами досліджень рекомендовано проводити конструктивні розрахунки промислових ГАПХ з умов теплообміну. In article it is described a design of a model sample gas hydrate accumulator natural cold (GHANC) for systems of cooling fruits and vegetables with active aeration and the stand for its tests. The technique and results of tests is resulted. Serviceability of a model sample in conditions is confirmed, characteristic for operation of systems cooling fruits and vegetables with active aeration. By results of tests it is recommended to carry out constructive calculations industrial GHANC from conditions of heat exchange.Item Вплив режимних параметрів на процес конденсації всередині горизонтальної труби(КНТУ, 2011) Горін, В. В.; Квасніков, В. П.; Gorin, V.; Kvasnikov, V.Item Технологічний процес відновлення гільз циліндрів методом термопластичного деформування(КНТУ, 2010) Капелюшний, Ф. М.; Кривоблоцька, Л. М.; Катеринич, С. Є.; Kapelushniy, F.; Krivoblockaya, L.; Katerinich, S.В статті запропоновано нову технологію відновлення гільз циліндрів за допомогою термопластичного деформування поверхонь. Розроблено раціональний план операцій технологічного процесу відновлення гільз для впровадження на ремонтних підприємствах при серійному і багатосерійному типах відновлення деталей. In the article new technology of proceeding in the shells of cylinders is offered by means of thermoplastic deformation of surfaces. The rational plan of operation of technological process of proceeding in shells is worked out for introduction on repair enterprises at the serial and serial types of proceeding in details.Item Оптимізація процесу охолодження гільз циліндрів двигунів внутрішнього згорання при їх термопластичному деформуванні(КНТУ, 2010) Капелюшний, Ф. М.; Калита, М. М.; Катеринич, С. Є.; Kapelushniy, F.; Kalita, N.; Katerinich, S.В статті розглянуто і проаналізовано фізичні процеси що протікають при різних способах охолодження в періоді термопластичного деформування поверхонь деталей. Запропоновано раціональний спосіб охолодження для впровадження на ремонтних підприємствах при серійному і багатосерійному типах відновлення деталей. To article are considered and analysed physical processes coolings proceeding at various ways in thermoplastic deformation of surfaces of details. The rational way of cooling for introduction on repair shops and mass type restoration details is offered.