Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
7 results
Search Results
Item Порівняльні показники роботи сошників двох типів(ЦНТУ, 2024) Сало, В. М.; Лещенко, С. М.; Вовнянко, Б. Г.; Мороз, С. М.; Salo, V.; Leshchenko, S.; Vovnianko, B.; Moroz, S.В статті розглянуті особливості забезпечення якісних показників виконання технологічного процесу сівби сільськогосподарських культур з використанням сошників різних типів. Представлена методика проведення польових порівняльних випробувань сошників з гострим кутом входження в ґрунт, які представлені експериментальною посівною секцією та серійним дводисковим сошником з прикочуючим котком. До складу секції входить сошник з гострим кутом входження в ґрунт, обладнаний утримуючою п’яткою. The article considers specific features of ensuring quality indicators of the technological process of sowing crops using coulters of various types. The existing designs of coulters are analysed, indicating their advantages and disadvantages. It is emphasised that the use of disc coulters for direct sowing is limited due to the need to apply significant efforts to deepen them into the soil. A well-known alternative design of operating parts for seed placement into the soil is a coulter with a sharp angle of entry, but its design and parameters need further improvement.The paper proposes the design of a sowing section for sowing spiked grain crops on the soil after no till tillage methods with the presence of plant residues in the upper soil layers. The basis of this sowing section is a coulter with a sharp angle of entry into the soil, the design of which provides the use of a holding heel.Item Обґрунтування окремих конструктивно-технологічних параметрів картоплепосадочної машини(ЦНТУ, 2024) Блащак, Б. О.; Бабій, А. В.; Blashchak, B.; Babii, A.У роботі запропоновано нову конструктивно-технологічну схему картоплепосадочної машини. Особливістю такої конструкції є те, що тут передбачено виконання смугового фрезерування по осі формованого ряду, а утворена ґрунтова стружка присипає насіння картоплі, яке вкладається на сформоване та ущільнене посадкове ложе. Дві пари загортачів формують спочатку малий гребень свіжим ґрунтом та фінальний великий гребень – ґрунтом з міжрядь. При виконанні дослідження обґрунтовано вибір кінематичного режиму роботи фрезерних барабанів по відношенню до товщини ґрунтової стружки, що вирізається ножами, та зроблено вибір типу загортачів. The purpose of the study is to substantiate the individual structural and technological parameters of the potato planting machine, which is used in the technology of growing potatoes and is intended for work in small farms in a unit with low-power energy sources.Item Результати експериментальних досліджень селекційно-насінницького трієра(ЦНТУ, 2023) Алієв, Е. Б.; Лупко, К. О.; Aliiev, E.; Lupko, К.Метою є експериментальне обґрунтування основних параметрів та режимів роботи селекційно- насінницького трієра дрібнонасіннєвих культур, розробка алгоритму роботи і програмного забезпечення відповідної мехатронної системи. Для проведення експериментальних досліджень розроблено й створено лабораторний селекційно-насінницький трієр. Для зміни частоти обертання циліндра і напрямку обертання використано плату керування Arduino UNO і драйвер електродвигуна постійного струму L298N. Керувати частотою і напрямом обертання циліндра можна в ручному режимі з використанням потенціометра і автоматичному з використанням монітор-порту Arduino IDE. Робочим органом трієра є циліндр, який складається з пластин із чарунками. В результаті експериментальних досліджень процесу сепарації дрібнонасіннєвих культур на лабораторному циліндричному чарунковому трієрі отримано залежності зміни мінімального θmin і максимального θmax кутів виходу насіння з чарунки циліндра трієра від маси вихідного матеріалу насіння M0, частоти обертання циліндра n та вмісту домішок f0. Отримані залежності увійшли до програмного забезпечення системи керування мехатронної системи, яке дозволяє налаштувати положення лотка для збору насіння в результаті керування сервоприводом. The goal is experimental substantiation of the main parameters and modes of operation of the selection and seed trier of small-seeded crops, development of the work algorithm and software of the corresponding mechatronic system. For conducting experimental research, a laboratory selection and seed trier was developed and created. To change the rotation frequency of the cylinder and the direction of rotation, the Arduino UNO control board and the L298N DC motor driver were used. The frequency and direction of rotation of the cylinder can be controlled manually using a potentiometer and automatically using the Arduino IDE monitor port. The working body of the trier is a cylinder, which consists of plates with shells. As a result of experimental studies of the process of separation of small-seeded crops on a laboratory cylindrical shell trier, the dependences of the change in the minimum θmin and maximum θmax angles of seed exit from the cylinder shell of the trier on the mass of the seed material M0, the rotation frequency of the cylinder n and the content of impurities f0 were obtained. The resulting dependencies are fed into the mechatronic control system software, which allows the position of the seed tray to be adjusted as a result of servo control.Item Розробка і калібрування блока вимірювання об’ємної маси потоку насіннєвого матеріалу соняшнику(ЦНТУ, 2019) Алієв, Е. Б.; Алиев, Э. Б.; Aliyev, E.Одним з елементів пропонованої раціональної прецизійної технологічної лінії процесів сепарації супер елітного насіннєвого матеріалу соняшнику є вібропневматичний сепаратор. Для вирішення недоліків відомого обладнання, а саме низької продуктивності і якості виконання операцій сепарації, очищення та розділення неоднорідної насіннєвої суміші за об’ємною масою на фракції, необхідно застосовувати автоматизовану систему керування, яка заснована на використані датчика об’ємної маси потоку насіннєвої суміші. Розроблено і проведено калібрування блока вимірювання об’ємної маси адаптивного вібропневматичного сепаратора. В результаті порівняння отриманих значень із традиційним методом вимірювання об’ємної маси (ДСТУ 4694:2006) за розрахованим критерієм Пірсона (χ 2) нормальність розподілу похибок вимірювань складає 2,13, більше за табличне значення χ 2(0,95;5) = 1,15. Поведена перевірка гіпотези про однорідність значень за допомогою критерію Кохрена G = 0,39Item Вплив розрідження на ймовірність появи пропусків та двійників при дозуванні насіння пневмомеханічним висівним апаратом(КНТУ, 2015) Бойко, А. І.; Попик, П. С.; Банний, О. О.; Bojko, Anatoliy; Popyk, Pavlo; Bannyi, OleksandrВ статті представлено результати експериментальних досліджень по встановленню впливу ступеня розрідження у вакуумній камері на появу пропусків та двійників при висіві насіння пневмомеханічним висівним апаратом, оснащеним комірками з направленим вектором дії. The aim is research of influence of the degree of liquefaction in a vacuum chamber to the emergence of omissions and doubles when dosing device with pneumomechanical seed doser directed action. Found that in the range of operating speeds (V = 0,2...0,6 m/s) reduces the likelihood of increase in liquefaction omissions several times. This indicates that apart forms seeds an important role in suction and transportation plays density material (seed weight) which affects the distribution effort in delighted her cell. Increased liquefaction contributes to the formation doubles, the number of which depends also on the shape of and density of seeds fit them to the cell. When increasing liquefaction increases probability of occurrence of doubles. At that, this dependencies is typical to all cultures. Dependencies are nonlinear character with the gradual increase of the likelihood doubles at rising liquefaction.Item Фактори, що впливають на оптимальні параметри роботи машини транспортерного типу для подрібнення насінника гарбуза(КНТУ, 2014) Думенко, К. М.; Думенко, І. В.; Павлюченко, І. С.; Нагерняк, Д. С.; Свірень, М. О.; Dumenko, К.; Dumenko, І.; Pavlyuchenko, І.; Nagernyak, D.; Sviren, М.Наведено проблему виділення насіння із насінника гарбуза з метою отримання насіннєвого матеріалу. Обрано фактори впливу на процес подрібнення насінника гарбуза розробленою машиною транспортерного типу. Описано конструкцію та принцип роботи даної машини. Викладено результати її лабораторних досліджень, за якими отримано графічні зображення двомірних перетинів поверхонь відгуку, як залежностей засміченості насіння і втрат від зміни трьох факторів. Встановлено основні параметри роботи машини транспортерного типу при виділенні насіння. Allocation problem are the seeds of a pumpkin. Chosen impacts on pumpkin seed crushing process developed machine conveyor type. We describe the design and principle of operation of the machine. The results of laboratory machines. According to the results obtained two-measured crossings of surfaces of reaction as dependencies debris seeds and losses from changes in the three factors, indentified key parametric specifications in the allocation of conveyor seeds.Item Спосіб сівби насіння просапних сільськогосподарських культур(КНТУ, 2015) Лобов, В. Й.; Vyacheslav, LobovНаведено спосіб висіву насіння, який полягає у визначені в атмосферному повітрі фізико- хімічних властивостей сільськогосподарського пилу - ґрунтову дефляцію, який виникає в робочій зоні при переміщені сівалки, обчислюють гігроскопічність цього пилу, по якому визначають вологість ґрунту, і в залежності від її рівня автоматично керують виконавчими механізмами сошників, наприклад гідроциліндрами, які регулюють потрібні глибини борозен для закладання в них насіння та визначають зусилля для ущільнення борозн, а по коефіцієнту спектральної яскравості сільськогосподарського пилу розраховують гумусові речовини ґрунту та керують потоками водяного розчину добрив і стимуляторів росту. Для пояснення надана блок-схема системи керування сівалкою, яка реалізує запропонований спосіб висіву насіння. The paper presents that to improve the accuracy of seeding and maximum field germination of seeds is necessary to consider the heterogeneity of soil properties, such as its moisture on the length of the rut. This is especially important in modern technology planting row crops is accompanied by a significant increase in performance and speed drills by sowing the field. Given way to seed, which is to determine the properties of the agricultural dust - dirt deflation, which occurs when you move the drill, this is calculated hygroscopic dust, which determine soil moisture, and depending on its level is automatically controlled actuators openers regulators need to lay the depth of furrows in their seeds. The method comprises creating sowing furrows in the soil, feeding them through the seed opener and seal grooves, while additionally provide training seed, combining it with the seed in the furrow by mixing in the opener seed flow with the flow of aqueous solution of fertilizers and growth stimulants and seal combine with the feeding grooves in them and the total flow of seed and fertilizer aqueous growth stimulants planting depth of soil moisture by intensive water, and further working area in the air seeder measuring physic-chemical properties of the agricultural dust (dust soil deflation), which occurs when moved sowing unit. Calculate the hygroscopicity of the dust, which determine the soil moisture content, and depending on its level is automatically controlled actuators sowing coulters, for example, hydraulic cylinders that regulate the depth of the furrows need for seeding. In the seed furrow portion of the water introduced to bring the soil moisture to an optimum state, provides the necessary seed germination if the soil moisture, calculated on the basis of its measurements before and during sowing of seed, less than critical, and determine the coefficient of the spectral brightness agricultural dust (soil dust deflation), which is calculated by soil holmic substances. Depending on the level of control actuators that regulate the flow of organic matter in the grooves, which are necessary for plants to provide the desired fertility. There is provided a block diagram of a control system drill, which realizes the proposed method for seeding.