Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Постійне посилання на фондhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Перегляд
10 результатів
Результати пошуку
Тип:Документ, Обґрунтування конструктивно-технологічних параметрів стрічково-гвинтового змішувача сипких кормів(ЦНТУ, 2023) Дудін, В. Ю.; Говоруха, В. Б.; Dudin, V.; Govorukha, V.Метою роботи було обґрунтування режимних параметрів роботи стрічково-гвинтового змішувача сипких кормів на основі експериментальних досліджень процесу. В результаті лабораторних досліджень процесу змішування сипких кормів експериментальним змішувачем встановлено наступне. Зі збільшенням часу та частоти обертання однорідність суміші збільшується і набуває максимуму 97,8 % при n = 48 хв-1 та t = 3,2 хв. після чого спостерігається незначне зменшення. Характер процесу близький до типової кінетики змішування сипких матеріалів. Витрати енергії на процес мають нелінійний характер, при цьому оптимум (найменше значення) знаходиться в точці, яка відповідає значенню частоти обертання 40,5 хв-1, а не в мінімумі n. При мінімумі k витрати енергії на процес складають 2,25 кВт/цикл а при максимумі – 3,66 кВт/цикл. Час змішування буде різний для різного вмісту найменшого компоненту і знаходиться в межах 2,9–3,56 хв. На основі отриманих даних встановлено раціональні параметри розроблюваного змішувача. The purpose of the work was to substantiate the operational parameters of the belt-screw mixer of bulk feed on the basis of experimental studies of the process. As a result of experimental studies of the process of mixing loose feed with an experimental mixer, the following was established. With increasing time and rotation frequency, the homogeneity of the mixture increases and reaches a maximum of 97.8% at n = 48 min-1 and t = 3.2 min. after which there is a slight decrease. The nature of the process is close to the typical kinetics of mixing loose materials. The energy consumption for the process is non-linear in nature, while the optimum (the smallest value) is located at the point corresponding to the value of the rotation frequency of 40.5 min-1, and not at the minimum n. At minimum k, energy consumption for the process is 2.25 kW/cycle, and at maximum – 3.66 kW/cycle. The mixing time will be different for different contents of the smallest component and is within 2.9–3.56 min. Based on the obtained data, the rational parameters of the mixer under development were established.Тип:Документ, Результати експериментальних досліджень малогабаритного експандера кормів(ЦНТУ, 2023) Алієв, Е. Б.; Дудін, В. Ю.; Лінко, М. О.; Aliiev, Е.; Dudin, V.; Linko, M.Застосування експандерів є необхідним у виробництві кормів і харчових продуктів, оскільки ці технічні засоби дозволяють покращити якість і поживні характеристики кінцевого продукту. Завдяки їх високій продуктивності і можливості регулювання тиску, експандери забезпечують ефективну обробку матеріалів, зберігаючи при цьому їх корисні властивості. Отже, оптимізація технологічних параметрів для формування експандатів залишається актуальною задачею в інжинірингу експандерів. Метою досліджень є обґрунтування конструктивно-технологічних параметрів малогабаритного експандера кормів експериментальним шляхом. В результаті експериментальних досліджень малогабаритного експандера кормів встановлені залежності зміни продуктивності експандера Q, його споживаної потужності N, питомої енергоємності процесу експандування q і щільності отриманих експандатів ρ від вологості комбікорму W, зазору між конусом та гайкою δс, частоти обертання гвинта n. Знайшовши в програмному пакеті Wolfram Cloud значення факторів досліджень при якому спостерігається мінімальне значення питомої енергоємності процесу експандування q = 30,7 кВт∙год/т встановлено, що W = 27,1 %, δс = 3,7 мм, n = 54,4 об/хв. При цьому продуктивність складала Q = 28,8 кг/год, споживана потужність N = 879 Вт, а щільність експандатів ρ = 336 кг/м3. The purpose of the research is to substantiate the structural and technological parameters of the smallsized fodder expander experimentally. The use of expanders is necessary in the production of feed and food products, as these technical means allow to improve the quality and nutritional characteristics of the final product. Thanks to their high productivity and the ability to adjust pressure, expanders provide effective processing of materials, while preserving their useful properties. Therefore, the optimization of technological parameters for the formation of expanders remains an urgent task in the engineering of expanders. As a result of experimental studies of a small-sized fodder expander, the dependences of the change in the productivity of the expander Q, its consumed power N, the specific energy capacity of the expansion process q and the density of the obtained expanders ρ on the moisture content of the compound feed W, the gap between the cone and the nut δс, and the frequency of rotation of the screw n were established. Having found in the Wolfram Cloud software package the value of the research factors in which the minimum value of the specific energy intensity of the expansion process q = 30.7 kWh/t is observed, it was established that W = 27.1 %, δс = 3.7 mm, n = 54.4 rpm. At the same time, the productivity was Q = 28.8 kg/h, the power consumption N = 879 W, and the density of the expanders ρ = 336 kg/m3.Тип:Документ, Експериментальні дослідження робочого процесу пневмотранспортера обчісаного вороху(ЦНТУ, 2021) Головльов, В. А.; Леженкін, О. М.; Holovlov, V.; Lezenkin, O.У статі наводяться переваги збирання зернових культур методом обчісування на корені з подальшою доробкою обчісаного вороху на стаціонарному пункті в порівнянні з комбайновим збиранням. Збирання цією технологією виконується причіпною збиральною машиною, яка складається з обчісуючого пристрою, ходової частини, транспортуючої системи. Параметри пневмотранспортеру збиральної машини є недостатньо обґрунтовані, тому подальшому наводяться результати експериментальних досліджень технологічного процесу пневмотранспортеру для транспортування обчісаного вороху зернових у причіп – візок, а саме дальність польоту обчісаного вороху в залежності від частоти обертання валу відцентрового вентилятору, питомої подачі вихідного матеріалу та кута нахилу рухомої заслінки. The article presents the advantages of harvesting grain ears by the method of combing at the root use stripper harvesting module technology with subsequent processing in comparison with combining. Harvesting with this technology is performed by a trailed harvesting machine with stripper working bodies. The implementation of this technology is constrained by namely the lack of scientific substantiation of the operating modes of the pneumatic conveyor of the combed heap. In this regard, there is a problem of researching the pneumatic conveyor, for its solution a method of experimental research was developed, which will determine the optimal parameters and performance of the pneumatic conveyor combed heap.The results of experimental researches of technological process of the pneumotransporter for transportation of the combed heap of grain in the trailer - the cart, namely range of flight of the combed heap depending on frequency of rotation dampers. The parameters of the factors and the geometric dimensions of the experimental setup were determined by computer simulation in SolidWorks. During the simulation, a full-fledged computer model was developed in real size, where the parameters were obtained by changing the speed of the impeller and changing the geometry of the loading window and the pneumatic line. Using the results of theoretical research, modeling and analysis of literature sources, the limits of the values of the factors were determined, which are given in the table. To conduct experimental research, an experimental setup was made, which allowed to vary the values of variable factors, and thus obtain a variety of data on the range of the combed pile of wheat depending on the values of variable factors. It is established that it is most expedient to use a noncomposite three - level Box - Benkin plan for three factors, which makes it possible to obtain a mathematical model according to the conducted experiments. The mathematical model is obtained, which in the future will make it possible to establish rational parameters and modes of operation of the compressed heap pneumatic conveyor. Checking the significance of the coefficients. The significance of the regression coefficients indicated that all the coefficients are significant. Checking the adequacy of the model showed that the model is adequate.Тип:Документ, Визначення раціональних параметрів пневмомеханічного висівного апарата з периферійним розташуванням комірок та інерційним видаленням зайвого насіння(ЦНТУ, 2019) Васильковська, К. В.; Васильковская, К. В.; Vasylkovska, K.В статті запропоновано нову конструкцію пневмомеханічного висівного апарата з периферійним розташуванням комірок на висівному диску та пасивним пристроєм, що дозволяє видаляти зайве насіння інерційним способом та забезпечити точний висів насіння просапних культур. Проведена серія досліджень запропонованого висівного апарата для насіння цукрових буряків дозволила визначити вплив розрідження у вакуумній камері висівного апарата та колової швидкості комірок на коефіцієнт заповнення комірок. Запропонована конструкція нового пневмомеханічного висівного апарата дозволяє значним чином знизити вакуум в системі, при цьому збільшується колова швидкість комірок висівного диска до значень поступальної швидкості посівного агрегату, що забезпечує сталу точку скидання насіння з висівного диска та однакові траєкторії їх польоту до борозни при якісному заповненні комірок. Для досягнення поставлених задач з визначення раціональних параметрів та режимів роботи висівного апарата використовувався метод планування багатофакторного експерименту. При цьому були визначені основні рівні та інтервали варіювання факторів для висіву насіння цукрових буряків при визначенні коефіцієнта заповнення комірок висівного диска. За допомогою пакету прикладних програм Statistica 6.0. для параметра оптимізації – коефіцієнта заповнення комірок побудовано поверхню відгуку та лінії рівного виходу. В статье предложено новую конструкцию пневмомеханического высевающего аппарата с перрифферийным распложением ячеек на высевающем диске и пассивным устройством, которое позволяет удалять лишниие семена инерционным способом и обезпечивает точный высев семян просапных культур. Проведенная сеиия исследованийпредложенного высевающего аппарата для семян сахарной свеклы позволила определить влияние разрежения в вакуумной камере высевающего аппарата и круговой скорости ячеек на коэфициент заполнения ячеек.Предложенная конструкция нового пневмомеханиченского высевающего аппарата позволяет значительным образом снизить вакуум в системе, при этом увеличивается круговая скорость ячеек высевного диска до значений поступальной скорости посевного агрегата,что обеспечивает постоянную точку сбрасывания семян с высеівного диска и одинаковые траектории их полета к борозне при качественном заполнении ячеек. Для достижения поставленных задач с определением рациональных параметров и режимов работы высевного аппарата использовался метод планирования многофакторного экспериментуа При этом были определены основные уровни и параметры варьирования факторов для висева семян сахарной свееклы при определении коэффициента заполнения ячеек высевного диска. С помощью пакета прикладных программ Statistica 6.0. для параметра оптимизации – коефициента заполнения ячеек построено повенрхность отклика и линии ровного выхода. Modern pneumatic sowing drill devices of high precision, despite a long history of their creation and improvement, have several disadvantages, the main ones are: insufficient dosing capacity caused by limited seed angular velocity of the disk (Vk ≤0,5 m/s) and the presence of uncontrolled redistribution random intervals between the seeds in the furrow, because of the high relative speed of the seed in contact with the latter during the drills movement with nominal speeds (Vc = 1,5...2,5 m/s). Eliminating these deficiencies is achieved by increasing the angular velocity of the sowing disk and its harmonization with the drills travelling speed. In the article we provide the new design of pneumatic sowing machine with peripheral cells on the seed disk and a passive device for removing extra seeds with inertia method for precise seeding of cultivated crops. A series of studies was proposed for sugar beet seeds sowing device, we defined the influence of dilution in a vacuum chamber of sowing device and angular velocity cell seed disk on the cells filling factor. The design of the new pneumatic sowing machine can significantly reduce the vacuum in the system having increased the angular speed in cell seed disk to the values of seeding device travelling speed, thus provide a constant point of seeds drop from the seed disc at the same trajectory of their flight to the furrows and the qualitative cells filling. To determine the rational parameters and modes of sowing device we used method of multifactor experiment planning. We determined the main levels and intervals of varying factors for sugar beet sowing along with determining the filling factor of cell seed disk. With application of package Statistica 6.0. for parameter optimization - cell seed disk filling factor was constructed response surface and line of even output. Thus, the design of the investigated pneumomechanical apparatus will allow to increase the circular velocity of the cells and reduce their number on the seeding disk, and to a considerable extent reduce the vacuum in the vacuum chamber. The proposed pneumomechanical seeding machine allows to increase the processability of sowing seeds of sown crops and reduce its energy intensity.Тип:Документ, Технічне забезпечення програмування врожайності(ЦНТУ, 2017) Васильковська, К. В.; Кулик, Г. А.; Носуленко, В. І.; Трикіна, Н. М.; Vasylkovska, K.; Kulik, G.; Nosulenko, V.; Trykina, N.Проведена серія досліджень нового пневмомеханічного висівного апарата з периферійним розташуванням комірок на висівному диску та інерційним видаленням зайвого насіння для підтвердження гіпотези щодо його універсальності. Конструкція нового пневмомеханічного висівного апарата дозволяє значно зменшити вакуум у системі, збільшивши колову швидкість комірок висівного диску, наблизивши її до значень швидкості руху посівного агрегату, таким чином забезпечуючи постійну точку скидання насіння з насіннєвого диска на тій же траєкторії їх польоту до борозни і якісне заповнення комірок. Для визначення раціональних параметрів і режимів роботи висівного апарата на насінні сої, соняшнику і кукурудзи проведена серія досліджень, отримані залежності коефіцієнта заповнення комірок від розрідження у вакуумній камері ΔP та колової швидкості комірок висівного диска V для перерахованих видів насіння. Таким чином, коефіцієнт заповнення комірок K=100% при дозуванні вказаних культур досягається встановленням наступних параметрів: для сої – ΔP=0,4…0,5 кПа, Vк=1,5…2,0 м/с; для соняшнику – ΔP=0,4…0,5 кПа, Vк=1,5…2,5 м/с. А висів насіння кукурудзи ускладнений великими розмірами насіння. A series of studies of a new pneumomechanical seeding machine with a peripheral arrangement of cells on the seed disk and inertial removal of excess seed has been carried out to confirm the hypothesis of its universality. The construction of a new pneumomechanical seeding machine can significantly reduce the vacuum in the system by increasing the speed of the seed disk cells, bringing it closer to the values of the speed of the sowing unit, thus ensuring a constant point of dumping the seeds from the seed disk on the same trajectory of their flight to the furrow and high-quality filling of the cells . A series of studies has been carried out to determine the rational parameters and operating conditions of seeding on soybean, sunflower and corn seed, the dependence of the filling factor of the cells on the vacuum in the vacuum chamber P and the speed of the seed cell disk V for these types of seeds have been obtained. Thus, the filling factor of the cells K = 100% at the dosage of these crops is achieved by setting the following parameters: for soybeans - ΔP=0,4…0,5 кПа, Vк=1,5…2,0 m / s; for sunflower - ΔP=0,4…0,5 kPa, Vк=1,5…2,5 m / s. And hanging seeds of corn is complicated by large seed sizes.Тип:Документ, Моделювання точного висіву пневмомеханічним висівним апаратом(КНТУ, 2016) Васильковська, К. В.; Vasilkovska, К.Проведена серія досліджень нового пневмомеханічного висівного апарата з периферійним розташуванням комірок на висівному диску та пасивним пристроєм для видаленням зайвого насіння інерційним способом на насінні цукрових буряків, визначено вплив розрідження у вакуумній камері висівного апарата та колової швидкості комірок висівного диска на коефіцієнт заповнення комірок. Запропонована конструкція нового пневмомеханічного висівного апарата дозволяє значно знизити вакуум в системі, збільшивib при цьому колову швидкість комірок висівного диска до значень поступальної швидкості посівного агрегату, тим самим забезпечити сталу точку скидання насіння з висівного диска та однакові траєкторії їх польоту до борозни при якісному заповненні комірок. Для визначення раціональних параметрів та режимів роботи висівного апарата використовувався метод планування багатофакторного експерименту. Визначено основні рівні та інтервали варіювання факторів для висіву насіння цукрових буряків при визначенні коефіцієнта заповнення комірок висівного диска. За допомогою пакету прикладних програм Statistica 6.0 для параметра оптимізації – коефіцієнта заповнення комірок висівного диска побудовано поверхню відгуку та лінії рівного виходу. A series of studies of new pneumatic sowing device w ith a peripheral cells to seed disk and a passive device for removing excess seeds inertia way of sugar beet seeds, the influence of dilution in a vacuum chamber sowing device and the angular velocity of cells seed disk to fill factor cells. The design of the new pneumatic sowing machine can significantly reduce the vacuum in the system having increased the angular speed in cell seed disk to the values of seeding device travelling speed, thus provide a constant point of seeds drop from the seed disc at the same trajectory of their flight to the furrows and the qualitative cells filling. To determine the rational parameters and modes of sowing device we used method of multifactor experiment planning. We determined the main levels and intervals of varying factors for sugar beet sowing along with determining the filling factor of cell seed disk. With application of package Statistica 6.0. for parameter optimization - cell seed disk filling factor was constructed response surface and line of even output.The most influential factor in the process of filling cells seed disc of a research pneumatic sowing machine is the value of the dilution factor because in order to achieve a filling cell value K = 100% should be ΔP = 0,2 ...0,3 kPa at the angular velocity of cells Va= 2.0 ... 2.5 m / s. Thus, the design of the studied pneumatic device makes it possible to increase the angular velocity of the cells and reduce their number on the sowing disk, and greatly reduce the dilution in a vacuum chamber. That is why the proposed seeding machine increases the technological efficiency of cultivated crops and reduces the energy costs.Тип:Документ, Експериментальні динамічні дослідження сил затиску захватних пристроїв промислових роботів(КНТУ, 2010) Павленко, І. І.; Годунко, М. О.; Pavlenko, І.; Godunko, М.У даній статті описано експериментальні динамічні дослідження сил затиску захватних пристроїв промислових роботів, які підтверджують правильність раніше виконаних теоретичних розрахунків. Також у статті показано графіки, що виводились на монітор комп’ютера при вимірюванні сил затиску для горизонтального руху руки робота та побудовано експериментальні і розрахункові криві відповідних залежностей. Dinamic researches of forces of clamp of gripper of industrial robots which confirm the rightness of the before described theoretical calculations are described in this article. Also the graphs which hatched on the monitor of computer at measuring of forces of clamp for the platforming of hand of robot and the experimental and calculation curves of the proper dependences are built are rotined in the article.Тип:Документ, Експериментальні дослідження пневмомеханічного висівного апарата з периферійним розташуванням комірок для висіву насіння просапних культур(КНТУ, 2012) Васильковська, К. В.; Vasilkovskaya, K.Проведено експериментальні дослідження нового пневмомеханічного висівного апарата з периферійним розташуванням комірок для висіву насіння просапних культур. Результати досліджень свідчать про можливість підвищення ефективності точного висіву. Experimental researches of new pneumomechanical sowing vehicle are conducted with the peripheral location of barns for sowing of seed of the cultivated cultures. The results of researches testify to possibility of increase of efficiency of seed-spacing.Тип:Документ, Вплив основних параметрів адаптованого качановідокремлювального апарату з інтегрованим подрібнювачем на якісні показники технологічного процесу збирання(КНТУ, 2014) Завірюха, М. В.; Zaviryuha, М.Визначено основні фактори, що найбільш суттєво впливають на якість технологічного процесу збирання стиглої кукурудзи з одночасним подрібненням листостеблової маси. Наведено основні результати експериментальних досліджень адаптованого одновальцевого качановідокремлювального апарату з інтегрованим подрібнювачем. Отримані математичні моделі та побудовано поверхні відгуків, за допомогою яких визначено оптимальне поєднання конструктивно-технологічних параметрів, що найбільш суттєво впливають на якість процесу збирання стиглої кукурудзи. The aim of work is an estimation of influence basic parameters of adapted corn picker vehicle of with one rolles with the integrated grinding down on the quality indexes of technological process of collection of ripe corn in the field terms. The main factors that most significantly affect the quality of the process picking ripe corn while grinding leafy mass. The basic experimental results drum apparatus adapted to separate heads with integrated chopper. Mathematical models and the surfaces of review by which defined the optimal combination of structural and technological parameters that most significantly affect the quality of the gathering of ripe corn. Possibility of diminishing to the degree of damase heads, increase of plenitude harvesting, and also degree of growing of lease mass shallow is experimentally well-proven by optimization of basic working organs and increase of their functionality.Тип:Документ, Фактори, що впливають на оптимальні параметри роботи машини транспортерного типу для подрібнення насінника гарбуза(КНТУ, 2014) Думенко, К. М.; Думенко, І. В.; Павлюченко, І. С.; Нагерняк, Д. С.; Свірень, М. О.; Dumenko, К.; Dumenko, І.; Pavlyuchenko, І.; Nagernyak, D.; Sviren, М.Наведено проблему виділення насіння із насінника гарбуза з метою отримання насіннєвого матеріалу. Обрано фактори впливу на процес подрібнення насінника гарбуза розробленою машиною транспортерного типу. Описано конструкцію та принцип роботи даної машини. Викладено результати її лабораторних досліджень, за якими отримано графічні зображення двомірних перетинів поверхонь відгуку, як залежностей засміченості насіння і втрат від зміни трьох факторів. Встановлено основні параметри роботи машини транспортерного типу при виділенні насіння. Allocation problem are the seeds of a pumpkin. Chosen impacts on pumpkin seed crushing process developed machine conveyor type. We describe the design and principle of operation of the machine. The results of laboratory machines. According to the results obtained two-measured crossings of surfaces of reaction as dependencies debris seeds and losses from changes in the three factors, indentified key parametric specifications in the allocation of conveyor seeds.