Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
4 results
Search Results
Item Технологічні особливості виготовлення дискових робочих органів ґрунтообробних та посівних машин(ЦНТУ, 2020) Кропівний, В. М.; Свірень, М. О.; Кузик, О. В.; Амосов, В. В.; Козловський, М. А.; Kropivny, V.; Sviren, M.; Kuzyk, O.; Amosov, V.; Kozlovsky, M.; Кропивный, В. Н.; Свирень, Н. А.; Кузык, А. В.; Козловский, Н. А.Провідні світові виробники досягають високих показників зносостійкості та міцності дисків з борвмісних сталей як їх хімічним складом, так і вибором раціональної технології термічної обробки. Експериментальні дослідження зразків деталей зі сталі марки 30MnB5 дозволили визначити, що для досягнення максимальних значень твердості достатньо нагріву протягом 15 хвилин до температури 850º С та гартування у воді. Щоб запобігти зниженню твердості та забезпечити необхідну пружність та в’язкість дисків, рекомендується відпускання при температурі 180º С. Розроблено технологічний процес та виробничу дільницю виготовлення сферичних дисків. The purpose of this study is to improve the technology of manufacturing spherical disk working bodies of tillage machines to increase their wear resistance and strength. The world's leading manufacturers achieve high wear resistance and strength of discs made of boron-containing steels both in their chemical composition and the choice of rational heat treatment technology. Experimental studies of 30MnB5 steel parts revealed that heating for 15 minutes to a temperature of 850°C and quenching in water was sufficient to achieve maximum hardness values. To prevent hardness reduction and to ensure the necessary elasticity and viscosity of the discs, it is recommended to temper at a temperature of 180°C and combine with heat before painting with powder paint. The application of cutting blanks with cutting of depressions along the outer contour of the disk and internal holes on the laser machine, as well as the formation of the finished shape of parts in the process of hot stamping and subsequent heat treatment in quenching dies. 1. The market of disk working bodies of tillage and sowing machines is studied, technological processes of manufacturing of which it is expedient to improve. 2. Theoretical and experimental study of the structure, structure and material properties of samples of spherical disks of imported agricultural machinery. The choice of 30MnB5 pine steel for their production is substantiated. 3. The improved technological process of manufacturing spherical disks is developed. It is recommended to form them by hot stamping in cold dies and intensive hardening in a water bath. 4. The project development of the section of production of disk working bodies of tillage and sowing equipment is carried out. Ведущие мировые производители достигают высоких показателей износоустойчивости и прочности дисков из борсодержащих сталей как их химическим составом, так и выбором рациональной технологии термической обработки. Экспериментальные исследования образцов деталей из стали марки 30MnB5 позволили определить, что для достижения максимальных значений твердости достаточно нагрева на протяжении 15 минут до температуры 850º С и закалки в воде. Чтобы предотвратить снижение твердости и обеспечить необходимую упругость и вязкость дисков, рекомендуется отпуск при температуре 180º С. Разработан технологический процесс и производственный участок изготовления сферических дисков.Item Дослідження властивостей моторної оливи в процесі експлуатації дизелів(КНТУ, 2009) Аулін, В. В.; Лисенко, С. В.; Кузик, О. В.; Aulin, V.; Lysenko, S.; Kuzyk, O.В статті дано комплекс показників, що характерезують зміну експлуатаційних властивостей моторної оливи в часі, наведено результати їх експерементального визначення. The complex of indexes is given in the article, that характерезують time-history of operating properties of agile olive is, results are resulted them determination.Item Вплив властивостей компонентів КМ (КП) на напружено-деформований стан і триботехнічні характеристики деталей СГТ(КНТУ, 2015) Аулін, В. В.; Кузик, О. В.; Носуленко, В. І.; Aulin, Viktor; Kuzyk, Oleksandr; Nosulenko, VictorРозглянуто різновиди контактування трибоелементів (ТЕ), зміцнених КМ (КП), які дозволяють істотно змінювати якість фізичного контакту, величину фактичної площі, здатність поверхневого шару (ПШ) ТЕ до еволюції складу і структури в процесі тертя та зношування. Виявлено ефективне гальмування руху дислокацій гетерогенними структурами КМ (КП), як при низьких, так і при високих температурах, а також рекристалізаційні процеси. Розглянуто напружений стан матеріалу ТЕ з КМ (КП) при терті. Отримано умову пластичної рівноваги компонентів у вигляді системи рівнянь та формула величини напруження при переході від матеріалу наповнювача до матеріалу матриці та визначено характер деформації, яким вони підлягають. Отримано вираз для критичного кута нахилу виступу і коефіцієнта тертя та проведена оцінка зміни коефіцієнта тертя. В процесі тертя і зношування ПШ КМ (КП) підлягає пружно-пластичному деформуванню, мало- або багато цикловому руйнуванню під силовим впливом, при протіканні теплових процесів та структурно-фазових перетворень, формуванню залишкових напружень різних знаків, спостерігається сумарний ефект силових, температурних та структурно-фазових залишкових напружень. The varieties of contact of triboelementov are considered tribo-element (TE), fortified composite material (CM) composition coating (CC), that allow substantially to change quality of physical contact, size of actual area, ability of superficial layer (SL) TE to the evolution of composition and structure in the process of friction and wear. The effective braking of motion of distributions the heterogeneous structures of CM(CC) is educed, both at subzero and at high temperatures, and also recrystallizations processes. The operating at a friction loading is distributed on hard fillers, that serve as opportune, barriers to movable distributions and reduce speed of flowage of matrix, that brings to the decline of intensity grasping over in a contact "matrix-matrix" and in a resiliently-plastic matrix there is relaxation of net voltages, minimum deformation and decline of probability of origin of cracks of tiredness. The tense state of material is considered TE of CM(CC) at a friction. The condition of plastic equilibrium of components as a system of equalizations and formula of size of tension are got in transition from material of filler to material of matrix and character of deformation is certain they are subject that. Expression for the critical angle of slope of performance and coefficient of friction and conducted estimation of change of coefficient of friction are got. In the process of friction and wear of SL CM(CC) subject to resiliently-plastic deformation, small- or much to cyclic destruction under power influence, at flowing of thermal processes and structurally-phase transformations, to forming of remaining tensions of different signs, there is a total effect of power, temperature and structurally-phase remaining tensions.Item Методи технічної реалізації модифікування композиційних олив накладанням електричного і магнітного полів та методики досліджень режимів тертя в сполученнях деталей(КНТУ, 2011) Кузик, О. В.; Kuzyk, A.В статті розглянуто розроблені схеми технічної реалізації модифікування композиційних олив накладанням електричних та магнітних полів на установках для фізичного моделювання процесів тертя і зношування в трибосистемі "гільза циліндра – поршневе кільце", імітації реальних процесів на одноциліндровій установці двигуна. Наведені методики дослідження режимів тертя на зазначених установках за різними параметрами. In the article the worked out charts of technical realization of retrofitting of composition butters imposition of the electric and magnetic fields are considered on fluidizers physical design of processes of friction and wear in a tribosystem "shell of cylinder is a piston-ring", to the imitation of the real processes and single-cylinder setting of engine. The brought methods over of research of the modes of friction on the noted options after different parameters.