Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
18 results
Search Results
Item Підвищення довговічності шестеренного насоса гідросистеми автотракторної техніки шляхом зниження зносів деталей, що утворюють радіальний зазор(ЦНТУ, 2022) Кулешков, Ю. В.; Черновол, М. І.; Красота, М. В.; Руденко, Т. В.; Осін, Р. А.; Kuleshkov, Yu.; Chernovol, М.; Krasota, M.; Rudenko, Т.; Osin, R.В роботі наведені результати досліджень залежності втрат робочої рідини через радіальний зазор. Визначені основні параметри, що на них впливають, та умови, при яких втрати робочої рідини будуть мінімальними, що відповідає раціональному значенню радіального зазору і забезпечує зменшення зносів деталей, які утворюють радіальний зазор. Встановлено, що підвищити довговічність шестеренного насоса можливо за рахунок того, що обробку шестерень і наступне складання шестеренного насоса здійснюють з гарантованим радіальним зазором в з’єднанні деталей «корпус – шестерні», що виключає початковий знос корпусу шестеренного насоса на при його обкатуванні. Запобіганню явища абразивного зношування сприяє збільшення радіального зазору до розмірів, через які спроможні вільно пройти абразивні частки будь–якої величини не зачепивши стінок корпусу і вершин зубів шестерень. Раціональний радіальний зазор забезпечує вільне проходження практично всіх абразивних часток що підвищує довговічність шестеренного насоса. The research goal is the determination of rational radial clearance, with what details, which create radial clearance, attrition will be minimal and eventually provides gear pump hydraulic systems of car and tractor machinery durability increasing. Research gives the results of the dependence of working liquid losses through radial clearance. Determined main parameters, which have an influence on them, and conditions due to which working liquid losses will be minimal, which corresponds to the rational value of radial clearance and provides decreasing of details attrition, which creates radial clearance. Were found as the main parameters, which allow managing working liquid losses through radial clearances. They consist of gear tooth tops width, gear rotation frequency, and outer gear radius. Offered a new conditions determination method, in which working liquid losses through radial clearances will be minimal. Mentioned models include the presence of pressurized and frictioned losses compounds. Was found that increasing gear pump durability is able due to gears processing and further gear pump assembling made with guaranteed radial clearance in connection «body - gears» details, which excludes initial attrition of gear pump body in time of its enabling. Increasing radial clearance to sizes, in which abrasive parts of any sizes are able to frequently walk through avoiding body walls and gear teeth tops, helps to prevent the abrasive attrition phenomenon. Rational radial clearance provides free passage for almost all abrasive parts, which increases gear pump durability. Rational radial clearance determination allows for increasing the efficiency of technology of gear pump manufacturing by rationalizing tolerances for gears manufacturing, which allows for increasing gear pump durability.Item Підвищення довговічності турбокомпресора в внаслідок ремонтного впливу(ЦНТУ, 2021) Кулєшков, Ю. В.; Черновол, М. І.; Красота, М. В.; Руденко, Т. В.; Солових, Є. К.; Осін, Р. А.; Kuleshkov, Yu.; Chernovol, M.; Rudenko, T.; Krasota, M.; Solovykh, Ye.; Osin, R.Для відновлення деталей машин можуть застосовуватися різноманітні способи відновлення і зміцнення. Однак далеко не всі способи можуть забезпечити необхідний ресурс для відновлення і зміцнення деталей, що працюють в абразивному та корозійному середовищі середовищах. Одним із сучасних напрямків підвищення зносостійкості та іншими властивостями відновлювальних покриттів є використання композиційних матеріалів. В цій статті представлені результати досліджень щодо розробки нового способу відновлення і зміцнення деталей композиційними матеріалами заснованими на використанні хімічного парофазного осадженням металів CVD - методу (Chemicikal Vapor Deposition) шляхом розкладання металоорганічних сполук. Показано, що розроблений композит матеріал, отриманий CVD – методом розкладання металоорганічних забезпечує підвищення зносостійкості не менше ніж в 2,0…2,2 раз в порівняні з новими деталями. A turbocharger is a unit of modern internal combustion engines designed to boost it. Since a drive of the turbocharger is most often carried out from the energy of the exhaust gases, the conditions of its operation can not be called favorable: the temperature of the exhaust gases sometimes reaches 7000C, high chemical activity of the exhaust gases, high speed of rotation of the turbine. The consequence of difficult operating conditions is the wear of its elements. One of the main causes of wear of the active elements of the turbocharger is abrasive wear. Various methods of restoration and strengthening can be used to restore machine parts. However, not all methods can provide the necessary resource for the restoration and strengthening of parts working in abrasive and corrosive environments. One of the modern directions of increasing the wear resistance and other properties of reducing coatings is the use of composite materials. This article presents the results of research on the development of a new method for restoring and strengthening parts with composite materials based on the use of chemical vapor deposition of metals CVD - method (Chemicikal Vapor Deposition) by decomposition of organometallic compounds. It is shown that the developed composite material obtained by the CVD-method of decomposition of organometallic compounds provides an increase in wear resistance of at least 2.0...2.2 times in comparison with new parts composite material. Vapor-phase deposition of metals, Chemicikal Vapor Deposition-method, decomposition of organometallic compounds.Item Дослідження розподілення електричного струму при відновленні автомобільних деталей контактним наварюванням(ЦНТУ, 2020) Кулешков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Осін, Р. А.; Kuleshkov, Yu.; Krasota, M.; Rudenko, T.; Osin, R.; Осин, Р. А.В статті розглянуті причини нерівномірності густини електричного поля при контактному наварюванні компактних (дріт, стрічка) та порошкових матеріалів при відновленні деталей автомобілів. Нерівномірність густини струму визначає нерівномірне розподілення температурного поля в зоні утворення литого ядра і впливає на якість наварених покриттів. При контактному наварюванні компактних матеріалів відбувається недогрівання центральної зони ядра, що спричиняється дією геометричного, температурного і магнітоелектричного чинників. При наварюванні порошкових матеріалів густина електричного поля вища в центральних зонах, що обумовлюється більш високим ступенем ущільнення порошкового матеріалу в цій зоні. При наварюванні порошкового матеріалу центральна зона нагрівається до більш високих температур ніж граничні зони. Неоднорідні електричні поля при контактному наварюванні розглянутих матеріалів приводять до зниження функціональних властивостей покриттів. The goal of completed research is determination of common factors of dynamic electricity distribution in the area of simple welding spot forming due to contact welding-on compact and powdered materials. Due to contact welding-on of compact (rod, belt) and powdered materials there is the dissimilarity of an electric field, which determines the unequal distribution of temperature field in the area of the moulded core creating and influence on the welded on covering quality. By the contact welding-on of compact materials, there is an occurrence of central core zone unheating, which is coming as a result of geometrical, temperature and magnetic-electric factors. During contact welding of metal powders, considering high speed of heating and a small-time of dynamic electricity passage through powder, it is possible to make a conclusion, that the stability of heat generation in a powder surface will be determined by starting electricity resistance value. High-quality plating can be reached if the powder charge will have low and stable electricity resistance in a cross-section and good compactness under the condition of low compress pressure, which is used for welding. (40 ... 70 MPa). Electrical field dissimilarity with contact welding-on powdered materials leads to unequal heating of powdered materials and covering defects, which is taking place due to the features of powder compression. As a result of current lines concoction in the central area is observed at a local temperature increase. Besides, interstices are dielectrical phase and increase electrical resistance in the peripheral areas. To increase the quality of coverings, got by contact welding-on is able due to providing high-quality powder material compression on the whole covering cut. В статье рассмотрены причины неравномерности плотности электрического поля при контактном наваривании компактных (проволока, лента) и порошковых материалов при восстановлении деталей автобилей. Неравномерность плотности тока определяет неравномерное распределения температурного поля в зоне образования литого ядра и влияет на качество наваренных покрытий. При контактном наваривании компактных материалов происходит недогрев центральной зоны ядра, что вызывается действием геометрического, температурного и магнитоэлектрического факторов. При наваривания порошковых материалов плотность электрического поля выше в центральных зонах, что обуславливается более высокой степенью уплотнения порошкового материала в этой зоне. При наваривании порошкового материала центральная зона нагревается до более высоких температур, чем граничные зоны. Неоднородные электрические поля при контактной наварке рассмотреных материалов приводят к снижению функциональных свойств покрытий.Item Анализ существующих конструктивных решений шестеренных насосов с регулируемой подачей(КНТУ, 2005) Кулешков, Ю. В.; Руденко, Т. В.; Кулєшков, Ю. В.В статье дан анализ известных конструктивных решений шестеренных насосов с регулируемой подачей. В статті подано аналіз відомих конструктивних рішень шестеренних насосів з регульованою подачею. In article gives an analysis of the known design solutions of the gear pumps with the regulated feed.Item Зниження масогабаритних показників шестеренного насоса оптимізацією параметрів зубчатого зачеплення(ЦНТУ, 2018) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Осін, Р. А.; Кулешков, Ю. В.; Осин, Р. А.; Kuleshkov, Yu.; Rudenko, T.; Krasota, M.; Osin, R.В статті розглянуті питання зниження маси і габаритів шестеренних насосів шляхом оптимізації параметрів зубчатого зачеплення. Оптимізація проводилась в напрямку підвищення питомих показників насоса: робочого об’єму і подачі. Підвищення питомих показників дозволило знизити габарити вузла насоса, що качає, шляхом зменшення ширини шестерень при збереженні робочого об’єму насоса, що в кінцевому результаті привело до зниження габаритних розмірів і маси зпроектованого насоса. В статье рассмотрены вопросы снижения массы и габаритов шестеренных насосов путем оптимизации параметров зубчатого зацепления. Оптимизация проводилась в направлении повышения удельных показателей насоса: рабочего объема и подачи. Повышение удельных показателей позволило снизить габариты качающего узла насоса путем уменьшения ширины шестерён при сохранении рабочего объема насоса, что в конечном результате привело к снижению габаритных размеров и массы спроектированного насоса. The object of the completed research is reducing mass and dimensions parameters of gear pump with saving of its technical characteristics and realization technical and economical effect. As the result of the optimization gear-tooth system parameters of gear pump, the construction of gear pump with increased specific working volume and output was designed. In the process of adapting the construction of an experimental pump with increased specific working volume to the production conditions, the possibility of decreasing of the gear width with keeping specific working volume, which corresponds to the standard value, was set. This made it possible to reduce the load on the pump bearings, with an offer of new dependence for calculating of the load on the pump bearing, which is determined by the gear-tooth system overlap coefficient. In the process of designing a gear pump with optimal parameters and the adaptation to its operating parameters to standard values, was found the possibility of reducing the dimensions and mass of the designed pump.Item Енергозберігаючий гідропривід механізму піднімання кузова автомобіля-самоскида(ЦНТУ, 2018) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Кулешков, Ю. В.; Kuleshkov, Yu.; Rudenko, T.; Krasota, M.В даній статті запропоновано конструкцію оригінального гідроприводу механізму піднімання кузова автомобіля-самоскиду. Особливістю даної гідросистеми є використання гідроакумулятора високого тиску, плунжерних насосів, системи керування, при цьому шестеренний насос та його привід від двигуна автомобіля, характерні для серійного механізму піднімання, в пропонованій схемі відсутні. Як джерело енергії, необхідної для піднімання кузова, пропонується використовувати не двигун внутрішнього згорання, як в серійних гідроприводах, а гідроакумулятор з підзаряджанням від коливань підресорених мас автомобіля. В статье предложено конструкцию оригинального гидропривода механизма подъема кузова автомобиля-самосвала. Особенностью данной гидросистемы является использование гидроаккумулятора высокого давления, плунжерных насосов, системы управления, при этом шестеренный насос и его привод от двигателя автомобиля, характерные для серийного механизма подъема, в предложенной схеме отсутствуют. В качестве источника энергии, необходимой для подъема кузова, предлагается использовать не двигатель внутреннего сгорания, а гидроаккумулятор с подзарядкой от колебаний подрессоренных масс автомобиля. The goal of researching is finding alternative constructions of hydraulic actuator of the carcass lifting device, which are working without using internal combustion engine energy and, consequently, guarantee energy saving and economical effect of technological car using. In the article it was offered the construction of original hydraulic actuator of the carcass lifting device. The feature of such hydraulic system is using hydraulic accumulator of high pressure, plunger pumps, control systems, herewith gear pump and its drive from car engine, which are specific for serial lifting mechanism, in the offered scheme are not present. As a source of energy, which is needed to lift the carcass, was offered not to use the internal combustion engine, but hydraulic accumulator with recharging from chattering of the car sprung mass. The feature of this hydrosystem is the use of a high pressure accumulator, plunger pumps, control system, with the gear pump and its drive from the engine of the car, typical for the serial lift mechanism, in the proposed scheme are absent. As a source of energy necessary for lifting the body, it is proposed not to use an internal combustion engine, as in serial hydraulic drives, and a hydraulic accumulator with the energy of the working fluid accumulated from the oscillations of the submerged car's masses. Was counted the economy, which can be earned by the reducing of the fuel uses, during realization of unloading operations of one car per year.Item Особенности работы и конструкции шестеренного насоса(ЦНТУ, 2017) Кулешков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Магонец, Е. В.; Осин, Р. А.; Кулєшков, Ю. В.; Магонець, Є. В.; Осін, Р. А.; Kuleshkov, Yu.; Rudenko, T.; Krasota, M.; Magonets, E.; Osin, R.В статье рассмотрены особенности конструкции шестеренного насоса, объясняющие его высокий уровень удельной мощности в сравнении с другими типами объемных насосов. Представлены в виде моделей характерные особенности работы шестеренного насоса, что позволило сформулировать пути дальнейшего усовершенствования конструкции шестеренного насоса в направлении повышения его технического уровня. В статті розглянуті особливості конструкції шестерінчастого насоса, які пояснюють його високий рівень питомої потужності у порівнянні з іншими типами об’ємних насосів. Представлено у вигляді моделей характерні особливості роботи шестеренного насоса, що дозволило сформулювати шляхи подальшого удосконалювання конструкції шестеренного насоса в напрямку підвищення його технічного рівня. The objective of research is to explain certain aspects of gear-type pump work, understanding of which allows to formulate tasks of farther increasing its technical level. The article describes the special aspects of construction gear-type pump, which explains its high level of unit power in comparison with other kinds of massive pumps. Submitted in a form typical aspects of gear-type pump work, which allows to formulate the ways of farther upgrading the gear-type pump construction towards increasing its technical level. Offered schemes of work allows to explain such negative feature in the gear-type pump as split off void, pulsating of pressure and giving in causal-resultative categories.Item Аналіз гідродинамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса(КНТУ, 2016) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Руденко, Т. В.; Красота, М. В.; Kuleshkov, Y.; Mahonets, E.; Kuleshkova, K.; Rudenko, T.; Krasota, M.В статті наведені результати аналізу впливу динамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса на його працездатність. Зазначені умови виникнення компресії і декомпресії робочої рідини у відсіченій порожнині шестеренного насоса. Встановлено взаємозв’язок між компресією і декомпресією робочої рідини, що виникають у відсіченій порожнині шестеренного насоса і негативним впливом цих явищ на працездатність насоса. Зазначено зниження працездатності шестеренного насоса внаслідок негативного впливу гідродинамічних явищ у відсіченій порожнині, що виявляється у підвищеному зношуванні деталей і з’єднань насоса, зниженні довговічності, коефіцієнту подачі, підвищенні пульсації тиску і подачі, збільшенні вібрацій і шуму НШ. The objective of the work is to analyse scientific and technical information and to determine further directions of research of processes taking place in the isolated section of a gear pump and to formulate scientific hypothesis of the research. The article presents the analysis results of the influence of dynamic processes taking place in the isolated section of a gear pump on its operational performance. The conditions of the occurrence of compression and decompression of hydraulic oil in the isolated section of a gear pump were determined. The interrelationship between the compression and decompression of the hydraulic oil which occurs in the isolated section of a gear pump and the negative influence of these effects on the operational performance of a pump was established. The decrease of operational performance of a gear pump is resulted by the negative influence of hydrodynamic effects in the isolated section. This results the excessive wear of the pump parts and interferences, decrease of service life, pump delivery rate and increase of pressure and delivery pulsation, vibration and noise of the gear pump. It was determined that scientific and technical information does not have physical and mathematic models with the description of hydrodynamic processes taking place in the isolated section of a gear pump. On the basis of the analysis of scientific and technical information we suggested a working hypothesis of the research with the result to exclude the gaps in theory and practice of a gear pump concerning hydrodynamic processes taking place in the isolated section of a gear pump.Item Анализ экспериментальных исследований пульсации мгновенной подачи шестеренного насоса(КНТУ, 2013) Кулешков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Кулешкова, К. Ю.; Кулєшков, Ю .В.; Руденко, Т. В.; Красота, М. В.; Кулєшкова, К. Ю.; Kuleshkov, Yuriy; Rudenko, Timofey; Krasota, Mikhail; Kuleshkova, KseniaВ статье представлены результаты анализа результатов экспериментальных исследований пульсации мгновенной подачи и давления за рабочий цикл шестеренного насоса и сравнение их с результатами теоретических исследований. В статті представлені результати аналізу результатів експериментальних досліджень пульсації миттєвої подачі та тиску за робочій цикл шестеренного насосу і порівняння їх з результатами теоретичних досліджень. The purpose of researches is the analysis of results of known pilot studies of a pulsation of the instantaneous submission and pressure of gear-type pumps, their comparing with an analysis result of theoretical development of this scientific and technical problem for development physical and mathematical models of process of the instantaneous submission of the gear-type pump. The analysis of the publications devoted to study of a pulsation of MGP, showed extremely wide interval of dispersion of irregularity degree of submission - from 1,25% to 100% that testifies to absence of adequate theoretical basis of process of the instantaneous submission of the gear-type pump. Contradictory data on a pulsation of submission and pressure testify that the developed physical and mathematical models of process of the instantaneous submission of the gear-type pump aren't able to explain the phenomenon of a pulsation of the instantaneous submission up to the end. Absence of theoretical generalization also leads to such contradictory results as experimenters have no correct methodical approach to this difficult phenomenon. From this the output about need of carrying out new own basic theoretical and experimental researches of this complex problem follows.Item Анализ теоретических исследований пульсации мгновенной подачи шестеренного насоса(КНТУ, 2013) Кулешков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Кулешкова, К. Ю.; Кулєшков, Ю. В.; Кулєшкова, К. Ю.; Kuleshkov, Yuriy; Rudenko, Tatyana; Krasota, Mikhail; Kuleshkova, KatyaВ статье представлены результаты анализа теоретических исследований пульсации мгновенной подачи и давления в процессе рабочего цикла подачи шестеренного насоса. В статті представлені результати аналізу теоретичних досліджень пульсації миттєвої подачі і тиску в процесі робочого циклу подачі шестеренного насоса. The purpose of research is the analysis of the known theoretical studies devoted to reducing ripple instantaneous flow and pressure gear pumps. Analysis of the publications on the study instantaneous flow pulsation, showed an extremely wide range of variation of degree of uneven flow - from 1.25% to 73%. The results showed that the available scientific information on the work of an instant surge flow and pressure are contradictory and indicate that the developed physical and mathematical model of the process instantaneous flow gear pump is unable to fully explain the phenomenon of pulsation. It is a deterrent to further improve the design of pump and includes a comparative analysis of the results of theoretical and experimental data and on the basis of the new in-depth theoretical and experimental studies of the process fluid supply in gear pumps.