Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
2 results
Search Results
Item Зниження масогабаритних показників шестеренного насоса оптимізацією параметрів зубчатого зачеплення(ЦНТУ, 2018) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Осін, Р. А.; Кулешков, Ю. В.; Осин, Р. А.; Kuleshkov, Yu.; Rudenko, T.; Krasota, M.; Osin, R.В статті розглянуті питання зниження маси і габаритів шестеренних насосів шляхом оптимізації параметрів зубчатого зачеплення. Оптимізація проводилась в напрямку підвищення питомих показників насоса: робочого об’єму і подачі. Підвищення питомих показників дозволило знизити габарити вузла насоса, що качає, шляхом зменшення ширини шестерень при збереженні робочого об’єму насоса, що в кінцевому результаті привело до зниження габаритних розмірів і маси зпроектованого насоса. В статье рассмотрены вопросы снижения массы и габаритов шестеренных насосов путем оптимизации параметров зубчатого зацепления. Оптимизация проводилась в направлении повышения удельных показателей насоса: рабочего объема и подачи. Повышение удельных показателей позволило снизить габариты качающего узла насоса путем уменьшения ширины шестерён при сохранении рабочего объема насоса, что в конечном результате привело к снижению габаритных размеров и массы спроектированного насоса. The object of the completed research is reducing mass and dimensions parameters of gear pump with saving of its technical characteristics and realization technical and economical effect. As the result of the optimization gear-tooth system parameters of gear pump, the construction of gear pump with increased specific working volume and output was designed. In the process of adapting the construction of an experimental pump with increased specific working volume to the production conditions, the possibility of decreasing of the gear width with keeping specific working volume, which corresponds to the standard value, was set. This made it possible to reduce the load on the pump bearings, with an offer of new dependence for calculating of the load on the pump bearing, which is determined by the gear-tooth system overlap coefficient. In the process of designing a gear pump with optimal parameters and the adaptation to its operating parameters to standard values, was found the possibility of reducing the dimensions and mass of the designed pump.Item Аналіз гідродинамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса(КНТУ, 2016) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Руденко, Т. В.; Красота, М. В.; Kuleshkov, Y.; Mahonets, E.; Kuleshkova, K.; Rudenko, T.; Krasota, M.В статті наведені результати аналізу впливу динамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса на його працездатність. Зазначені умови виникнення компресії і декомпресії робочої рідини у відсіченій порожнині шестеренного насоса. Встановлено взаємозв’язок між компресією і декомпресією робочої рідини, що виникають у відсіченій порожнині шестеренного насоса і негативним впливом цих явищ на працездатність насоса. Зазначено зниження працездатності шестеренного насоса внаслідок негативного впливу гідродинамічних явищ у відсіченій порожнині, що виявляється у підвищеному зношуванні деталей і з’єднань насоса, зниженні довговічності, коефіцієнту подачі, підвищенні пульсації тиску і подачі, збільшенні вібрацій і шуму НШ. The objective of the work is to analyse scientific and technical information and to determine further directions of research of processes taking place in the isolated section of a gear pump and to formulate scientific hypothesis of the research. The article presents the analysis results of the influence of dynamic processes taking place in the isolated section of a gear pump on its operational performance. The conditions of the occurrence of compression and decompression of hydraulic oil in the isolated section of a gear pump were determined. The interrelationship between the compression and decompression of the hydraulic oil which occurs in the isolated section of a gear pump and the negative influence of these effects on the operational performance of a pump was established. The decrease of operational performance of a gear pump is resulted by the negative influence of hydrodynamic effects in the isolated section. This results the excessive wear of the pump parts and interferences, decrease of service life, pump delivery rate and increase of pressure and delivery pulsation, vibration and noise of the gear pump. It was determined that scientific and technical information does not have physical and mathematic models with the description of hydrodynamic processes taking place in the isolated section of a gear pump. On the basis of the analysis of scientific and technical information we suggested a working hypothesis of the research with the result to exclude the gaps in theory and practice of a gear pump concerning hydrodynamic processes taking place in the isolated section of a gear pump.