Збірник наукових праць КНТУ. Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/18
Свідоцтво про державну реєстрацію у Міністерстві юстиції України: серія КВ, №15253-3825 ПР.
Затверджено наказом Міносвіти і науки України № 1528 від 29.12.14р.
ISSN 2409-9392 (Online) 2409-9392(Print)
Мови видання: українська, російська, англійська, періодичність - один раз на рік;
Browse
8 results
Search Results
Item Дослідження процесу затвердіння та прогнозування структури литих чавунних молольних тіл(ЦНТУ, 2018) Ломакін, В. М.; Клименко, В. В.; Пукалов, В. В.; Кузик, О. В.; Дубодєлов, В. І.; Горюк, М. С.; Ломакин, В. Н.; Кузык, А. В.; Дубоделов, В. И.; Lomakin, V.; Klymenko, V.; Pukalov, V.; Kuzyk, O.; Dubodelov, V.; Goriuk, M.Розглядається використання методу скінченних елементів для чисельного розрахунку процесу затвердіння виливків молольних тіл циліндричної і сферичної форми в кокілі в залежності від хімічного складу сплаву та для прогнозування співвідношення між кількістю ледебуриту, що визначає зносостійкість молольних тіл, та кількістю аустеніто-графітної евтектики. Рассматривается использование метода конечных элементов для численного расчета процесса затвердевания отливок мелющих тел цилиндрической и сферической формы в кокиле в зависимости от химического состава сплава и для прогнозирования соотношение между количеством ледебурита, что определяет износостойкость мелющих тел, и количеством аустенито-графитный эвтектики. The aim of the study was to calculate the kinetics of crystallization and to determine the rational mode for cooling castings of a crushing cylinder and a crushing ball in metallic form to ensure that the surface wear-resistant bleached layer does not have more than a third of the size (or radius of the ball) from the surface of the body. The use of the finite element method for numerical calculation of solidification of castings of grinding bodies of cylindrical and spherical bodies in chill molds is considered depending on the chemical composition of the alloy and for predicting the ratio between the amount of ledeburite, which determines the wear resistance of grinding bodies, and the amount of austenite-graphite eutectic. The experimental chemical composition of cast iron for grinding bodies: 3-3.9% C, 2.8-4% Si, 0.6-1.2% Mn; less 0.03% P, less 0,02% S. For cylindrical and spherical bodies, the thermal conductivity functional was obtained and the kinetics of crystallization of castings was calculated. The data obtained indicate an inhomogeneity in the distribution of the linear rate of solidification along the cross-section of cast products. At the beginning of the process, the solidus front has a relatively high velocity (0.08 mm / s), which rapidly decreases with increasing thickness of the crust. Further, with the passage of time, the thickness of the two-phase zone gradually decreases and in the central part of the casting the rate of solidification is ~ 0.005 mm / sec. It is established that the microstructure of low-chromium cast iron (~ 1% Cr) is perlite-ledeburite. The carbide phase is represented by doped cementite (Fe, Cr)3С. A comparative analysis of the operational properties and the cost of their achievement showed that in today's conditions, it is a compromise to make cast grinding bodies from low-alloyed cast iron (0.8-1% Cr). The data obtained by the calculation method are in good agreement with the results of production tests of cast grinding bodies, which made it possible to optimize the technology for manufacturing such products.Item Дослідження впливу температури і швидкості руху розплаву на процес розчинення легуючих добавок в рідкому чавуні(ЦНТУ, 2017) Ломакін, В. М.; Клименко, В. В.; Ломакін, А. В.; Дубодєлов, В. І.; Горюк, М. С.; Lomakin, V.; Klimenko, V.; Lomakin, A.; Dubodelov, V.; Goryuk, M.Досліджено та вивчено вплив тепло-кінетичних та масо-обмінних процесів в магнітодинамічному міксері-дозаторі моделі МДН-6Ч на швидкість розчинення ферохрому у рідкому чавуні. Виконано розрахунки конвективної дифузії хрому та експериментальним шляхом встановлено раціональний режим роботи магнітодинамічної установки при отриманні розплавів легованого чавуну. The aim of the study was to determine the rational combination of the temperature of the metal-solvent and the rate of supply of the melt from the channel to the working capacity of the MDN-6CH unit in order to obtain the minimum dissolution time of ferrochrome and the maximum productivity in smelting the alloy with a given mass fraction of chromium. It was explored and studied an influence of the heat-kinetic processes on a speed of ferrochromium dissolution in a liquid cast iron in a magnetodynamic mixer-feeder (MDN-6CH). It was done calculations of the chromium's convective diffusion and it was set the rational mode of magnetodynamic installation’s operation when this installation was receiving a melt of the cast iron. Calculations showed a practical test confirmed that at low doping iron with chromium (chromium content in molten less than 1%), minimum duration dissolution and homogenization of molten ferrochrome reached at the metal-solvent at a temperature 1380-1420º C. The consumption of metal in the channel of the magnetodynamic installation should be ~ 2-5 kg / s, which ensures the rate of movement of the solvent relative to the pieces of alloying additives at a level of 0.35-0.45 m/s.Item Експериментальна оцінка ефективності регенерації картриджів побутових фільтрів доочистки питної води(ЦНТУ, 2017) Клименко, В. В.; Ковальчук, Н. В.; Кравченко, В. І.; Klymenko, V.; Kovalchuk, N.; Kravchenko, V.Наразі для додаткової очистки питної води розповсюджене застосування побутових фільтрів зі змінними картриджами. Картриджі мають обмежений термін експлуатації, що викликає потребу в їх відносно частій заміні, певною альтернативою якій може бути відновлення очищувальної спроможності шляхом регенерації. В статті описано методику та результати експериментальної оцінки ефективності доочистки питної води побутовими фільтрами з регенерованими картриджами. Технологічний ланцюг регенерації складається з послідовної обробки фільтрувальних матеріалів розчином лугу, розчином NaCl та промивки відстояною водою (без розборки картриджів). Наведено результати аналізу домішок у водопровідній воді, обробленій регенерованими картриджами побутових фільтрів та виконано їх порівняння з величиною наявних аналогічних домішок у воді, доочищеній новими картриджами. Отримані результати свідчать про можливість застосування даного методу регенерації для відновлення роботи картриджів побутових фільтрів доочистки питної води. To date, for additional purification of drinking water, household filters with replaceable cartridges are widely used. Cartridges have a limited lifespan, which causes the need for their relatively frequent replacement, a certain alternative of which can be the restoration of purifying ability by regeneration. The technique and results of the experimental evaluation of the efficiency of post-treatment of drinking water with household filters with regenerated cartridges are described in the article. The technological chain of regeneration consists of sequential processing of filter materials with a solution of alkali, NaCl solution and washing with standing water (without disassembly of cartridges). The results of the analysis of impurities in tap water treated with regenerated household filter cartridges are presented and compared with the amount of existing similar impurities in water, refined with new cartridges. The obtained results testify to the possibility of using this regeneration method for restoring the work of cartridges of household filters for post-treatment of drinking water.Item Підвищення енергоефективності концентрування водних розчинів виморожуванням(КНТУ, 2016) Клименко, В. В.; Переверзєв, І. О.; Ковальчук, Н. В.; Klymenko, Vasyl; Pereverzev, Igor; Kovalchuk, NatalyaПідвищення ефективності техніки та процесів концентрування водних розчинів виморожуванням, зокрема шляхом зменшення енерговитрат, є важливим і актуальним. Ціль досліджень даної роботи – підвищити енергоефективність способу концентрування водних розчинів виморожуванням при застосуванні газоподібного холодоагенту (ГПХ). В роботі визначена функціональна залежність енерговитрат на концентрування водних розчинів виморожуванням із застосуванням ГПХ від величини тиску в установці концентрування та визначений оптимум (мінімум) функції такої залежності. При підвищених тисках газоподібного холодоагенту (повітря) в області значень 0,2 МПа ≤ Р ≤ 0,5 МПа енерговитрати в установці концентрування водного розчину виморожуванням мінімальні та менші, ніж при атмосферному тиску в 1,6 ÷ 1,8 рази. The purpose of this research is a way to increase the efficiency of concentrating aqueous solutions using freeze, by using refrigerant gas (RG). Preliminary analysis showed, that the value of energy consumption, substantially depends on the pressure, that applying to RG circulation, in the circuit inside the installation for concentrating of solutions. To achieve the goals, we need to figure out the functional dependence of energy consumption of aqueous solutions concentrating by using RS freeze, on the pressure in the installation, and determine the optimum (minimum) value of such dependence. We have developed a methodology, and performed calculations of energy consumption on movement and replenishment of air, and general energy consumption, depending on pressure of RG (air) during a process of aqueous solution concentrating by freeze. It’s determined, that concentrating of the aqueous solution by freeze, using RG (air) at high pressure, in a range of values of 0.2 MPa ≤ P ≤ 0.5 MPa, takes less energy consumption, then concentrating at the atmospheric pressure in 1,6 ÷ 1,8 times.Item Дослідження впливу кінетики кристалізації на властивості кокільних виливків чавунних цильпебсів(КНТУ, 2016) Ломакін, В. М.; Клименко, В. В.; Пукалов, В. В.; Ломакін, А. В.; Lomakin, Viktor; Klimenko, Vasil; Pukalov, Viktor; Lomakin, AndriyРозглядається використання методу математичного моделювання для визначення часу початку і закінчення процесу кристалізації легованих чавунів у кокілі в залежності від хімічного складу сплаву та для прогнозування співвідношення між кількістю ледебуриту, що визначає зносостійкість цильпебсів (молольних циліндрів), та кількістю аустеніто-графітної евтектики. The aim of this work is studying how speed of hardening and chromium's modified additives affect to structure of cast iron's cylinder in metallic form for rising of the shock and abrasive durability. Here is examined use of mathematical modeling to identify the start time and end time of hardening alloying metal, depending on the chemical composition of the alloy, and to predict the ratio between amount of ledeburite, which determines the durability of the cylinder, and number of austenite-graphite eutectic. Comparative analysis of performance properties and value of its achievements showed that today the best compromise is to manufacture grinding bodies from cast iron . The cast iron has to be low alloyed by the chromium(0.8-1%).Item Стендові випробовувуння макетного зразка газогідратного акумулятора природного холоду(КНТУ, 2012) Клименко, В. В.; Корнієнко, В. Н.; Скрипник, О. В.; Klymenko, V.; Kornienko, V.; Skrypnyk, А.У статті описано конструкцію макетного зразка газогідратного акумулятора природного холоду (ГАПХ) для систем охолодження плодів і овочів з активним вентилюванням і стенд для його випробовувань. Приведено методику і результати випробовувань. Підтверджено працездатність макетного зразка в умовах, характерних для експлуатації систем охолодження плодів і овочів з активним вентилюванням. За результатами досліджень рекомендовано проводити конструктивні розрахунки промислових ГАПХ з умов теплообміну. In article it is described a design of a model sample gas hydrate accumulator natural cold (GHANC) for systems of cooling fruits and vegetables with active aeration and the stand for its tests. The technique and results of tests is resulted. Serviceability of a model sample in conditions is confirmed, characteristic for operation of systems cooling fruits and vegetables with active aeration. By results of tests it is recommended to carry out constructive calculations industrial GHANC from conditions of heat exchange.Item Газогідратна технологія утилізації двооксиду вуглецю із сатураторного газу цукрового виробництва(КНТУ, 2011) Скрипник, О. В.; Клименко, В. В.; Skrypnyk, A.; Klymenko, V.Розроблено принципову схему та термодинамічний цикл альтернативної газогідратної технологічної установки утилізації двооксиду вуглецю, в якій передбачено отримання СО2 із відпрацьованого сатураторного газу цукрового виробництва у вигляді льдогазгідратних капсул двооксиду вуглецю і сухого льоду. Отримано розрахункові рівняння, необхідні для проектування газогідратних елементів розглянутої установки, а саме кристалізатора газогідратів і утворювача льодогазгідратних капсул. The circuit diagramme and thermodynamic cycle of alternative gas hydrates the fabrication system of a utilizations of carbon dioxide in which one it is envisioned productions СО2 from completed the carbonator sugar production gas in an aspect capsule of carbon dioxide gas hydrate and dry ice sheaths is developed. The rated equations indispensable for projection gas hydrates of units of observed installation, namely a crystallizer pan gas hydrates and installation for building capsule of carbon dioxide gas hydrate sheaths are gained.Item Експериментальні дослідження нестаціонарних теплових режимів неізольованих проводів повітряних ліній перед процесом обледеніння(КНТУ, 2014) Козловський, О. А.; Орлович, А. Ю.; Клименко, В. В.; Kozlovskyi, Oleksandr; Orlovych, Аnatolij; Klymenko, VasylijДля визначення діапазонів уставок системи технічної діагностики проводів при обледенінні проведені лабораторні дослідження. Описані умови і методи експериментальних досліджень, лабораторне обладнання та конструкція досліджуваних зразків проводу. Діапазон потужності охолодження зразка неізольованого проводу АС- 50/8, необхідної для утворення на ньому штучних ожеледно-паморозевих відкладень, при найбільш ймовірних метеорологічних умовах для його природнього обледеніння склав 0,25-0,17 Вт/см. Отримані експериментальні дані дозволять підвищити точність роботи систем технічної діагностики проводів в умовах обледеніння. In the article were conducted laboratory studies to determine the ranges of technical diagnostics settings of wires at icing process. We described the conditions and methods of experimental research, laboratory equipment and design of wire samples. Cooling process power range of the sample non isolated wire AC- 50/ 8, required for the formation of the artificial ice and frost deposits at the most likely weather conditions for its natural icing was 0,25-0,17 W / cm. The experimental data will improve the accuracy of technical diagnostics wires in icing conditions.