Збірник наукових праць КНТУ. Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/18
Свідоцтво про державну реєстрацію у Міністерстві юстиції України: серія КВ, №15253-3825 ПР.
Затверджено наказом Міносвіти і науки України № 1528 від 29.12.14р.
ISSN 2409-9392 (Online) 2409-9392(Print)
Мови видання: українська, російська, англійська, періодичність - один раз на рік;
Browse
24 results
Search Results
Item Ідентифікація співвідношення руда/вода на вході кульового млина(КНТУ, 2006) Кондратець, В. О.; Сербул, О. М.В статті приведені результати досліджень алгоритмічного методу підвищення точності ідентифікації технологічних параметрів при управлінні кульовими млинами. Показано, що можлива ідентифікація співвідношення руда/вода на вході кульового млина по технологічним параметрам його комунікацій в умовах вимірювання витрати пульпи в пісковому жолобі з пониженою точністю. In article are brought results of the studies of the algorithmic method of increasing to accuracy to identifications technological parameter when control ball mill. It Is Shown that possible identification of the correlation ore/water at the input ball mill on technological parameter its communication at condition of the measurement of the consuption of the pulp in sand chute with reduced by accuracy.Item Оптимізація точності прогнозування співвідношення руда/вода в кульовому млині з циркулюючим навантаженням(КНТУ, 2016) Кондратець, В. О.; Сербул, О. М.; Kondratets, Vasily; Serbul, AlexanderВибір пристроїв вимірювання технологічних параметрів за похибкою можливо подати як задачу оптимізації відповідно методу динамічного програмування у три стадії, у кожній з яких обирається один з засобів. В процесі оптимізації при відносній похибці вимірювання витрати пульпи у пісковому жолобі ±3,0 % відносна максимальна похибка прогнозування співвідношення руда/вода склала 1,72 % при визначенні витрати руди і води в млин з похибкою ±1,0 % порівняно з допустимою ±3,0 %. The purpose of the article is a search for the best combination of precision instruments for the margin of error prediction liquefaction. The ratio of the ore/water predict possible in accordance with this algorithm on the measured parameters - ore and water consumption in a ball mill, a volume flow of ore and water in a ball mill, a volume flow of sand in sand classifier chute. The measurement error of each parameter introduces an error in the final result. he task is complicated by the fact that the volumetric flow of sand in the sand chute accurately measure is not possible, which significantly reduces the result of forecasting where the measurement error or most approximates the boundary permissible value of ± 3,0% for the ratio of ore/water. Selection device for measuring process parameters of error may be represented as the optimization problem by the method of dynamic programming in three stages, each of which selects one means. In the process of optimizing the relative error of flow measurement in sand chute ± 3,0%, the maximum relative error of prediction ratio of ore / water amounted to 1.72% as determined by the flow of ore and water in the mill with an accuracy of ± 1,0% compared with the allowable ± 3 0%.Item Дослідження перемішування матеріалів у кульовому млині як багатовимірному керованому об’єкті(КНТУ, 2016) Кондратець, В. О.; Мацуй, А. М.; Kondratets, Vasily; Matsui, AnatoliiВстановлено, що осереднення твердого у кульовому млині відбувається достатньо швидко, практично за 34 с. Більш проблематичним є перемішування твердого з водою. Запропоновано воду у кульовий млин до необхідного розрідження пульпи подавати трьома потоками – на поверхню вихідної руди, у приймальний пристрій завиткового живильника до граничного розрідження пісків класифікатора та безпосередньо у горловину кульового млина, розбризкуючи її в широкій зоні завантаження. The aim of work is to study the mixing of materials along the drum of the ball mill, which works in a closed circuit with mechanical single- qualifier for its improvement. The ball mill as a multidimensional object has four output value. In this article a study performed on one of them - the parameter of the mixing materials, which is characterized, on the one hand, averaging the size of the solid, on the other hand, by mixing the solid with water. It is found that the averaging of the solid is not very dependents on its shape and size, in ball mill it happens sufficiently rapidly for 34 seconds, practically continuously improving the performance for a given time interval. More problematic is the mixing of the solid and water, which under the existing conditions is carried on a length of 1/4 ... 1/3 mill drum and which in consequence, does not actively participate in the grinding of the ore. Proposed that the water in a ball mill should be fed to the required dilution of the pulp by the three streams - to the surface of the original ore, the receiver cochlear feeder to the classifier boundary liquefaction sand directly into the throat of a production unit, spraying it into a wide area load. The proposed approach supplying water into a ball mill provides inclusion 1/4 ... 1/3 the length of the drum in efficient crushing of ore, which greatly improves the performance of his work.Item Дослідження кульового млина як керованого об’єкта по каналу продуктивності(КНТУ, 2008) Кондратець, В. О.; Рева, О. М.; Карчевська, М. О.Приведені результати розробки моделі кульового млина як керованого об’єкта по каналу продуктивності по готовому продукту. Показана можливість керування подрібненням з використанням вихідного живлення, циркулюючого навантаження, розрідженості пульпи та споживаної потужності. Для здійснення такого керування необхідно розробити засіб ідентифікації завантаження кульового млина рудою та підхід автоматичного формування й підтримання бажаної характеристики крупності кульового навантаження. Results of development of model of a spherical mill as controlled object on the channel of productivity on a ready product are resulted. The opportunity of management by crushing with use of the initial meal, circulating loading, dilution pulps and is shown power consumption. For realization of such management it is necessary to develop means of identification of loading of a spherical mill ore and the approach of automatic formation and maintenance of the required characteristic to the largeness spherical loading.Item Стендові дослідження системи автоматичної стабілізації витрати води(КНТУ, 2008) Сербул, О. М.; Кондратець, В. О.; Сидоренко, В. В.У статті приведені методика та результати стендових досліджень системи автоматичної стабілізації витрати води в пісковий жолоб класифікатора. Встановлено, що в межах експлуатаційних змін тиск і температура води практично не впливають на точність системи. Відносна похибка дозування склала ± 0,85 %. In article are brought methods and results of the stand studies of the system of automatic stabilization of the consumption of water in sand chute of the qualifier. It is installed that within the range of working change the pressure and the temperature of water practically do not influence upon accuracy of the system. Relative inaccuracy of measure has formed ± 0,85 %.Item Дослідження кульового млина, що подрібнює піски класифікатора, по каналу розрідження пульпи(КНТУ, 2008) Кондратець, В. О.; Мацуй, А. М.В статті приведені результати дослідження кульового млина, що подрібнює піски класифікатора, по каналу розрідження пульпи. Показано, що похибка ідентифікації співвідношення руда/вода не приводить при регулюванні до зміни режиму агрегату. Не допустимо в якості керуючого діяння використовувати зміну витрати води, яка подається безпосередньо у кульовий млин. In the article the results of research of ball mill, grinding down sands of classifier are resulted in the article, on the channel of dilution of mash. It is rotined that error of authentication of correlation ore/water does not lead at adjusting to the change of the mode of aggregate. It is not possible as managing influence to utillize the change of rate-of-flow, which is given directly in a ball mill.Item Обґрунтування вибору параметра регулювання норми висіву системою автоматичного керування зерновими сівалками(КНТУ, 2013) Пархоменко, Ю. М.; Кондратець, В. О.; Пархоменко, М. Д.; Parhomenko, Y.; Kondratec, V.; Parhomenko, М.У статті приведені результати теоретичного обґрунтування параметра регулювання норми висіву системою автоматичного керування зерновими сівалками з котушковими висівними апаратами. Отримані і проаналізовані залежності інтенсивності висіву від швидкості руху сівалки, робочої довжини котушки і передаточної величини, а також щільності розподілу зерна вздовж рядка висіву від робочої довжини котушки і передаточної величини. Показано, що в якості параметра регулювання САК процесом висіву зернової сівалки доцільно прийняти щільність розподілу зерна вздовж рядка висіву, яка лінійно залежить від керуючого діяння - робочої довжини котушки висівного апарата. The aim is to justify the choice of control parameters seeding rate of the automatic control system with coil-grain sowing machines. The paper presents the results of a theoretical study of the parameter control seeding rate automatic control system grain seeders with the coil sowing machines. Obtained and analyzed according to the intensity of the speed of the seed drill, the working length of the coil and the transfer value and the density of the grain flow along the row seeding of the working length of the coil and the transfer value. It is shown that, as a control parameter of the ACS process seed corn planter is advisable to take the density distribution of seeds along the row seeding, which is a linear function of the control action - the working length of the coil sowing. Rightly selected control parameter - the density distribution of seeds along the row seeding allows for the automatic control seeding rate that will ensure even distribution of seeds and a significant increase in productivity.Item Теоретичне дослідження розрідження пісків односпірального класифікатора джерелом з незмінною витратою води(КНТУ, 2013) Кондратець, В. О.; Сербул, О. М.; Kondratets, V.; Serbul, A.Приведені результати теоретичного дослідження розрідження пісків односпірального класифікатора джерелом з незмінною витратою води. Встановлено, що, враховуючи особливості роботи технологічної схеми, можливо застосувати джерело подачі води у пісковий жолоб класифікатора з незмінною і обґрунтованою продуктивністю. The aim is to establish the possibility of filing a constant flow of water in a sand trough classifier with stabilization diluting the slurry in a ball mill that grinds the sand with the base ore. The possibility of stabilizing the flow of water in the gutter sand one scroll classifier with stabilization diluting the slurry in a ball mill that grinds the sand along with the base ore. Using the proposed approach and analytical expressions can in almost any operating conditions justify the fixed cost of water in the gutter sand one scroll classifier, where a broad range of flow ore ball mill, its density and the circulating load for reliable transport of slurry and liquefaction of production vessels. The implementation of this approach to improve the accuracy of identification ratio ore/water in a ball mill by eliminating transaction flow measurement in sand trough and effect of the transport delay.Item Дослідження нелінійної системи автоматичного управління подачею води у кульовий млин, що подрібнює піски класифікатора(КНТУ, 2013) Мацуй, А. М.; Кондратець, В. О.; Matsui, A.; Kondratets, V.Обґрунтована функціональна схема системи автоматичного управління подачею доданої води у кульовий млин, що подрібнює піски двоспірального класифікатора, та її складові елементи. Показано, що вона повинна містити обчислювальний блок, який формує змінне задаюче діяння на витрату доданої води, та ідеалізований елемент, що спрацьовує при занадто низьких рівнях вхідного сигналу і має характеристику без гістерезису. The aim is to study the automatic control system of water supply in a ball mill that grinds the sand classifier. It is shown that the stabilization of dilution of the pulp in a ball mill, which grinds sands double-qualifier is necessary to organize an incomplete invariant ratio control solid / liquid in the receiver cochlear feeder and final input to the ball mill feed into the neck of a small amount of water. Proposed a non-linear system of automatic control supply of water added to the ball mill containing idealized relay element and a computer unit, which in terms of the pulp and the actual ratio of solid / liquid in the receiver cochlear feeder, set ratio solid / liquid and the density of the ore forming variable sets the effect on water consumption. Idealized relay element and computing unit implemented in the controller. Idealized relay element operates at extremely low levels of the input signal and has the feature without hysteresis. The proposed automatic control system is stable and has high quality.Item Теоретичне дослідження відкритого гідростатичного перетворювача параметрів рідких середовищ(КНТУ, 2008) Кондратець, В. О.; Мацуй, А. М.У статті приведені результати теоретичних досліджень відкритого гідростатичного перетворювача параметрів рідких середовищ. Показано, що вихідний сигнал перетворювача залежить як від рівня рідкого середовища, так і від його повного тиску. На перетворювач здійснює вплив густина рідкого середовища при визначенні і рівня, і тиску. Висота перетворювача для умов приймального пристрою завиткового живильника може складати 0,6 м. The results of theoretical researches of the opened hydrostatical transformer of parameters of liquid environments are resulted in the article. It is rotined that the output signal of transformer depends both on the level of liquid of environment and from its complete pressure. On him the closeness of liquid of environment has influence at determination of both level and pressure. The height of transformer for the terms of takers-off of snail feeder can make 0,6 m.
- «
- 1 (current)
- 2
- 3
- »