Збірник наукових праць КНТУ. Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/18
Свідоцтво про державну реєстрацію у Міністерстві юстиції України: серія КВ, №15253-3825 ПР.
Затверджено наказом Міносвіти і науки України № 1528 від 29.12.14р.
ISSN 2409-9392 (Online) 2409-9392(Print)
Мови видання: українська, російська, англійська, періодичність - один раз на рік;
Browse
7 results
Search Results
Item Система корекції норми висіву на базі кореляційного датчика швидкості руху посівного агрегата(КНТУ, 2006) Горевий, І. М.; Єніна, І. І.; Руденко, Т. Г.Запропоновано використання безконтактного кореляційного датчика для узгодження процесу висіву та швидкості руху сівалки з метою підвищення точності висіву за рахунок виключення впливу похибок від проковзування опорно - приводних коліс посівного агрегата. Use of the contactless correlation sensor for the coordination of seeding process and speed of movement of the seeder is offered with the purpose of increase of accuracy of a seeding due to exception of influence of errors from sliding basic driven wheels of the sowing unit.Item Розробка автоматизованої системи керування обробкою деревини на поздовжньо-фрезерних верстатах(КНТУ, 2012) Руденко, Т. Г.; Єрмолаєв, Ю. О.; Шалімов, В. О.; Rudenko, Т.; Ermolaev, U.; Shalimov, V.В статті запропоновано нову автоматизовану комбіновану систему керування механізмами поздовжньо-фрезерних верстатів з метою отримання необхідної продуктивності, якості виробів та енергозбереження. In the article the new automated combined control system of the milling machines mechanisms is proposed with a view to get the required performance, product quality and energy savings.Item Модель систем електроприводів деревообробного верстата(КНТУ, 2013) Руденко, Т. Г.; Rudenko, T.У статті дана методика розрахунку моменту навантаження на привод фрези. Запропоновано імітаційну модель, яка дозволяє дослідити реакцію систем електроприводів на зовнішнє збурення у вигляді моменту навантаження. Проведено аналіз осцилограм струму статора асинхронного двигуна приводу фрези і результатів натурного випробування. The purpose of work is analytical determination disturbing influences on the milling drive from cutting unit and comparison reactions the stator current of the model and the real oscillograms during giving static moment. The creating mathematical and simulation models of control objects and studying their response to perturbations is an important step in the design of control systems. This paper presents computation of the mathematical model of the woodworking machines electric drives load. The simulation model was constructed on the basis of the equations using computer software, allowing explore the reaction of electric drives on changes wooden workpieces parameters. The oscillograms of stator current an asynchronous motor of milling cutter, obtained by simulation and by result of natural tests are shown. Thus the model obtained by the proposed method allows determine the load on the cutters drive. Using this load in simulation model of the system causes a change in the stator current engine, similar to the reaction in real drive.Item Інформаційно-комп’ютерна система контролю процесу фрезерування деревообробного верстата(КНТУ, 2014) Руденко, Т. Г.; Єрмолаєв, Ю. О.; Rudenko, Tatyana; Yermolaev, YuriyСтаття присвячена побудові системи контролю параметрів динамічного стану деревообробного поздовжньо-фрезерного верстата. З аналізу досліджень і публікацій встановлено, що важливими інформативними параметрами є вібрація, завантаження приводів фрези та подачі заготовки, шорсткість обробленої поверхні. В роботі визначені допустимі граничні значення вище вказаних параметрів, наведено структурну схему системи контролю та програмний алгоритм роботи мікроконтролера. Article is devoted to the construction of the control system of the dynamic state of woodworking milling machines. The analysis showed that the vibration, loading of milling cutter’s drives and feed drive of billet, surface finish are the important informative parameters. In this paper the permissible limit values of the above parameters were defined, a block diagram of the control system was built, algorithm of microcontroller's work was shown . The developed control system will improve the function of the machine without changing its structure, avoid overloading the engine, unbalancing mechanical parts of the machine, prevent the appearance of defective items and get the products specified quality.Item Визначення параметрів асинхронних двигунів з побудовою статичних характеристик для приводів фрезерувального верстата СФ-АСТРА-РК8(КНТУ, 2010) Єрмолаєв, Ю. О.; Руденко, Т. Г.; Ermolaev, U.; Rudenko, T.Стаття присвячена визначенню параметрів схеми заміщення за паспортними даними асинхронних двигунів АИР80A2 та АИР160S2 електроприводів фрезерувального верстата СФ-АСТРА-РК8, побудові механічних і електромеханічних характеристик двигунів з аналізом їх та визначенням розрахункової похибки. The article is devoted to definition of parameters of an equivalent circuit on nameplate data of asynchronous engines of АИР80A2 and АИР160S2 electric drives of the milling machine tool of СФ-АСТРА-РК8, to construction of mechanical and electromechanical characteristics of the specified engines with their analysis and definition of a settlement error.Item Обґрунтування впровадження системи плавного пуску для привода фрез верстата СФ-АСТРА-РК8(КНТУ, 2012) Єрмолаєв, Ю. О.; Руденко, Т. Г.; Ermolaev, U.; Rudenko, Т.В статті описано моделювання і дослідження пускових процесів привода ріжучого інструмента деревообробного верстата СФ-АСТРА-РК8. Визначені витрати енергії при прямому і плавному пусках, побудовані електродинамічні характеристики струму та моменту при різних вхідних параметрах ТПН, обґрунтовано доцільність використання тиристорних перетворювачів напруги та надані рекомендації щодо вибору управляючих параметрів тиристорних пускозахисних пристроїв для привода ріжучого інструмента верстата СФ-АСТРА-РК8. In the article the modelling and analysis starting processes of cutting tool drive wood-working machine SF-ASTRA-RK8 are described. The losses of energy at the direct and soft starting are defined, the electrodynamic descriptions of current and moment are built at the different entry parameters of TPN, the expedience of the use thyristor tension transformers is justified and the recommendations on the choice of managing parameters of thyristor soft start devices for the cutting tool drive machine tool SF-ASTRA-RK8 are gave.Item Експериментальні дослідження електроприводів верстата СФ-АСТРА-РК8(КНТУ, 2009) Єрмолаєв, Ю. О.; Руденко, Т. Г.; Босов, Є. П.Стаття присвячена експериментальному дослідженню роботи електроприводів деревообробного верстата СФ-АСТРА-РК8 в режимах пуску, холостого ходу і при навантаженні. Наведені та проаналізовані осцилограми пусків асинхронних двигунів подачі та головного інструмента, їх взаємодія при обробці деталей з деревини. The article is devoted experimental research of work of woodworking machine-tool of SF-ASTRA-RK8 in the modes of starting, idling and at loading. Resulted and analyzed oscillograms of starting of asynchronous engines of serve and main instrument, their cooperation at treatment of wooden details.