Збірник наукових праць КНТУ. Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/18
Свідоцтво про державну реєстрацію у Міністерстві юстиції України: серія КВ, №15253-3825 ПР.
Затверджено наказом Міносвіти і науки України № 1528 від 29.12.14р.
ISSN 2409-9392 (Online) 2409-9392(Print)
Мови видання: українська, російська, англійська, періодичність - один раз на рік;
Browse
18 results
Search Results
Item Розмірна обробка електричною дугою бічної поверхні напрямного ролика з композиційного матеріалу на основі реліту(ЦНТУ, 2018) Сіса, О. Ф.; Пукалов, В. В.; Свяцький, В. В.; Сиса, О. Ф.; Свяцкий, В. В.; Sisa, O.; Pukalov, V.; Sviatskyi, V.Виконано обґрунтування технологічної схеми формоутворення зовнішньої бічної поверхні напрямного ролика, способом розмірної обробки електричною дугою з урахуванням особливостей фізичних механізмів їх утворення та гідродинамічних явищ в міжелектродному проміжку. Встановлені аналітичні зв’язки технологічних характеристик процесу розмірної обробки електричною дугою твердого сплаву «Реліт» з режимами обробки і геометричними параметрами. Выполнено обоснование технологической схемы формообразования внешней боковой поверхности направляющего ролика, способом размерной обработки электрической дугой с учетом особенностей физического механизма образования и гидродинамических явлений в межэлектродном промежутке. Установлены аналитические связи технологических характеристик процесса размерной обработки электрической дугой твердого сплава «Релит» с режимами обработки и геометрическими параметрами. The article is dedicated to development of technology and equipment of rough machining method by electric arc of a guide roller side surface, as high performance alternative to traditional methods of rough machining. During operation, the damage to the surface of the hard alloys guide roller caliber occurs by abrasion and chipping of carbide particles. The development of net shaped roll marks occurs by the occurrence of hotbeds of accelerated cluster abrasion and chipping of smaller particles with subsequent growth of these areas and unification in a closed net shaped roll marks. The turned out particles of hard alloy leave the machining marks on the wire, in such a worn the hard alloy rolling roller does not meet the specified dimensions and it is reground to a smaller diameter by grinding of diamond tool on the rough machining stage. It is proposed on the stage of rough machining to remove the worn-out profile of a guide roller side surface with help of dimensional electric arc, which allows you to remove big allowances of material at the lowest treatment costs. It is suggested to get the lateral surface by dimensional electric arc with a given roughness of Ra = 10..20mkm, which allows you to take great allowances material at the lowest cost processing time.In this case, the processing cycle of hard alloy side surface decreased of 1,4…2,6 times. The justification of technical scheme of forming the guide roller side surface by electric arc sizing method is done taking into account features of physical formatting mechanism and hydrodynamic phenomena in the electrode gap. The analytical communication of technological characteristics of rough machining process by electric arc made of composite material, based on relit, with the modes of processing and geometric parameters are established. The obtained models allow to control the productivity and specific productivity, specific electricity consumption, quality and surface accuracy which is processed, predicted and optimized given characteristics. A technical solution is proposed that allows to expand the technological possibilities of processing the guide roller.Item Вплив деформаційних умов і виду розділового середовища на контактне схоплювання адгезійно-сумісних металів(КНТУ, 2004) Шепельський, М. В.; Свяцький, В. В.; Свяцька, Л. П.; Shepelskyi, M.; Sviatskyi, V.; Sviatska, L.Проведена експериментальна перевірка моделі контактного схоплювання адгезійно-сумісних металів на прикладі пресування дискретного середовища. Experimental verification of contact adhesion model of adhesion-compatible metals on the example of a discrete medium extrusion are considered.Item Реологічні особливості на поверхні адгезійно сумісних металів при пружній деформації системи(КІСМ, 1998) Шепельський, М. В.; Свяцький, В. В.; Пукалов, В. В.; Пукалов, В. П.; Shepelskyi, M.; Sviatskyi, V.; Pukalov, V.; Pukalov, V.Запропоновано технологію виробництва волокон пресуванням литих гранул. На основі аналізу реології на контакті частинок, які деформують, і стану лінії розриву швидкостей в процесі їхнього пресування зроблено висновок про можливість отримання дискретних волокон адгезійно сумісних металів. The technology of fibers production by meens cast granules extrusion is proposed. Based on the rheology analysis on the contact of the deformed granules and the state of the line of velocity discontinuity during the process of their extrusion, it is concluded that it is possible to obtain discrete fibers of adhesively compatible metals.Item Перевірка математичної моделі прогнозування властивостей деталей сільськогосподарських машин, отриманих із полімерів в ультразвуковому полі(КДТУ, 2001) Василенко, Ф. І.; Лук’яненко, Л. П.; Свяцький, В. В.; Vasylenko, F.; Lukianenko, L.; Sviatskyi, V.Представлено результати експериментального підтвердження математичної моделі прогнозування властивостей деталей сільськогосподарських машин, отриманих із полімерів в ультразвуковому полі. The experimental verification results of the mathematical model of properties agricultural machines details obtained by polymers in the ultrasonic field are presented.Item Методика приготування металографічних шліфів з волокнистих свинцевих зразків(КДТУ, 2000) Шепельський, М. В.; Свяцький, В. В.; Пукалов, В. В.; Shepelskyi, M.; Sviatskyi, V.; Pukalov, V.Розглянута методика приготування металографічних шліфів з волокнистих свинцевих зразків. Method of metallographic slabs preparation made of fibrous lead samples are considered.Item Особливості контактного схоплювання при зсувних деформаціях адгезійно-сумісних металів(КНТУ, 2004) Шепельський, М. В.; Свяцький, В. В.; Свяцька, Л. П.; Пукалов, В. В.; Shepelskyi, M.; Sviatskyi, V.; Sviatska, L.; Pukalov, V.Розглянуто механізм контактного схоплювання адгезійно-сумісних металів на прикладі пресування дискретного середовища. The contact seizure mechanism of adhesion-compatible metals on the example of the pressing of a discrete medium are considered.Item Оцінка величини схоплювання дискретних тіл при пресуванні(КНТУ, 2007) Свяцький, В. В.; Свяцька, Л. П.; Sviatskyi, V.; Sviatska, L.Наведено спосіб і пристрій для визначення величини контактного схоплювання адгезійно-сумісних металів на прикладі пресування дискретного середовища. In the article the method and device for determination of grip value of the adhesive compatibility metal by the example of the discrete medium extrusion are considered.Item Дослідження характеру руйнування поверхні контакту дискретних частинок при зсувних деформаціях(КНТУ, 2007) Свяцький, В. В.; Свяцька, Л. П.; Sviatskyi, V.; Sviatska, L.Розглянуті особливості реології на контакті гранул в умовах інтенсивних зсувних деформацій. Досліджувалися текстури деформації і механізм руйнування деформованих ниток. Встановлено, що руйнування поверхні поділу контактуючих гранул при їхньому пресуванні носить в’язкий характер. In the article the problems of a feature of a rheology on the contact of discrete particles in conditions of intensive shift deformations are considered. The textures of deformation and mechanism of destroying of distorted particles were researched. It is established, that the destroying of an interface of contacting particles at their molding has ductile cup-shaped character.Item Розробка привода для глибокого свердлення методом перехоплення стебла інструмента по його довжині(КНТУ, 2008) Пестунов, В. М.; Свяцький, В. В.; Свяцька, Л. П.Наведені теоретичні і експериментальні дослідження механізмів приводів верстатів для глибокого свердління, що мають проміжні опори. Показано, що застосування пристроїв, що використовують змінну величину вильоту інструмента в процесі обробки глибоких отворів, приводить до збільшення періоду його стійкості. In the article the theoretical and experimental research of mechanisms of machine tools drives for the deep drilling, having intermediate anvil post, are considered. The application of devices with a variable tool extension in deephole machining is bring to a tool durability are demonstrated.Item Розвантаження свердла при комбінованій обробці глибоких отворів(КНТУ, 2008) Пестунов, В. М.; Свяцький, В. В.; Свяцька, Л. П.Наведено схему розвантаження свердла, що основана на використанні комбінованої обробки „різання – пластична деформація”. Спосіб вирішує задачу зниження складових технологічного навантаження і дозволяє розширити технологічні можливості процесу свердління по глибині обробки. The scheme of drill unloading, based on use of the combined processing „cutting – plastic deformation”, is considered. The method solves a problem of technological load components decrease and allows expanding technological capability of drilling process on depth of processing.