Збірник наукових праць КНТУ. Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/18
Свідоцтво про державну реєстрацію у Міністерстві юстиції України: серія КВ, №15253-3825 ПР.
Затверджено наказом Міносвіти і науки України № 1528 від 29.12.14р.
ISSN 2409-9392 (Online) 2409-9392(Print)
Мови видання: українська, російська, англійська, періодичність - один раз на рік;
Browse
3 results
Search Results
Item Розмірна обробка електричною дугою бічної поверхні напрямного ролика з композиційного матеріалу на основі реліту(ЦНТУ, 2018) Сіса, О. Ф.; Пукалов, В. В.; Свяцький, В. В.; Сиса, О. Ф.; Свяцкий, В. В.; Sisa, O.; Pukalov, V.; Sviatskyi, V.Виконано обґрунтування технологічної схеми формоутворення зовнішньої бічної поверхні напрямного ролика, способом розмірної обробки електричною дугою з урахуванням особливостей фізичних механізмів їх утворення та гідродинамічних явищ в міжелектродному проміжку. Встановлені аналітичні зв’язки технологічних характеристик процесу розмірної обробки електричною дугою твердого сплаву «Реліт» з режимами обробки і геометричними параметрами. Выполнено обоснование технологической схемы формообразования внешней боковой поверхности направляющего ролика, способом размерной обработки электрической дугой с учетом особенностей физического механизма образования и гидродинамических явлений в межэлектродном промежутке. Установлены аналитические связи технологических характеристик процесса размерной обработки электрической дугой твердого сплава «Релит» с режимами обработки и геометрическими параметрами. The article is dedicated to development of technology and equipment of rough machining method by electric arc of a guide roller side surface, as high performance alternative to traditional methods of rough machining. During operation, the damage to the surface of the hard alloys guide roller caliber occurs by abrasion and chipping of carbide particles. The development of net shaped roll marks occurs by the occurrence of hotbeds of accelerated cluster abrasion and chipping of smaller particles with subsequent growth of these areas and unification in a closed net shaped roll marks. The turned out particles of hard alloy leave the machining marks on the wire, in such a worn the hard alloy rolling roller does not meet the specified dimensions and it is reground to a smaller diameter by grinding of diamond tool on the rough machining stage. It is proposed on the stage of rough machining to remove the worn-out profile of a guide roller side surface with help of dimensional electric arc, which allows you to remove big allowances of material at the lowest treatment costs. It is suggested to get the lateral surface by dimensional electric arc with a given roughness of Ra = 10..20mkm, which allows you to take great allowances material at the lowest cost processing time.In this case, the processing cycle of hard alloy side surface decreased of 1,4…2,6 times. The justification of technical scheme of forming the guide roller side surface by electric arc sizing method is done taking into account features of physical formatting mechanism and hydrodynamic phenomena in the electrode gap. The analytical communication of technological characteristics of rough machining process by electric arc made of composite material, based on relit, with the modes of processing and geometric parameters are established. The obtained models allow to control the productivity and specific productivity, specific electricity consumption, quality and surface accuracy which is processed, predicted and optimized given characteristics. A technical solution is proposed that allows to expand the technological possibilities of processing the guide roller.Item Технологія виготовлення порожнин високоміцних гайок спеціального призначення(ЦНТУ, 2017) Сіса, О. Ф.; Пукалов, В. В.; Юр’єв, В. В.; Sisa, O.; Pukalov, V.; Yuryev, V.Виконано обґрунтування технологічної схеми формоутворення поверхонь порожнини високоміцної гайки спеціального призначення, способом розмірної обробки електричною дугою з урахуванням особливостей фізичних механізмів їх утворення та гідродинамічних явищ в міжелектродному проміжку. Встановлені аналітичні зв’язки технологічних характеристик процесу розмірної обробки електричною дугою сталі 20Г2Р з режимами обробки і геометричними параметрами. The article is devoted to the development of technology and equipment for the method of electric arc machining of cavities of high-strength screw-nuts for special purposes, as a highly effective alternative to traditional methods of processing. In the conditions of a single and small-scale production, high-strength nuts of special purpose with an internal cavity under a special key for tightening are used to assemble and fasten the critical elements of mining equipment, therefore it is economically disadvantageous to use the technology of stamping such nuts because of the high cost of the die tooling. The technology for manufacturing of special screw-nuts consists of two basic operations: obtaining a special nut billet and forming an internal special profile. An important factor in increasing the load-bearing capacity of high-loaded high-strength screw-nuts is to increase the elasticity of the thread. This is ensured by the grade of material and the quality of the steel billet. When developing technology and equipment, it is necessary to take into account the conditions that will ensure the production of high-quality threads and the formation of a reinforced cavity under a special tightening key with an appropriate surface roughness. Therefore, the method of dimensional processing by electric arc makes it possible to obtain hardened cavities with an appropriate roughness for a special tightening key. It is established that the optimal parameters of the walls of the cavities of high-strength screw-nuts of special purpose at processing capacity M = 6010 mm³ / min., dimensional electric arc, there is a roughness Ra = 6,3..21 mkm, which provides the necessary geometric dimensions and surface quality. It is proposed to receive cavities of high-strength screw-nuts of special purpose with a dimensional electric arc with a given roughness Ra = 6,3..21 mkm, side walls, which allows you to shoot large material allowances with the least time spent on processing. At the same time, the treatment cycle of the cavity of high-strength screw-nuts for special purposes decreased 10 times. The feasibility study of the technological scheme for the formation of cavities of high-strength screw-nuts of a special purpose by the method of dimensional processing by an electric arc is made, taking into account the features of the physical mechanism of formation and hydrodynamic phenomena in the interelectrode gap. Analytical links of technological characteristics to the process of dimensional processing by an electric arc of steel 20G2Р, with processing modes and geometrical parameters are established.Item Розмірна обробка твердосплавних волок(КНТУ, 2014) Сіса, О. Ф.; Осипенко, М. В.; Стебліна, К. В.; Sisa, Oleg; Osipeko, Marina; Steblina, KaterinaВиконано обґрунтування технологічних схем формоутворення поверхонь твердосплавної волоки способом розмірної обробки електричною дугою з урахуванням особливостей фізичних механізмів їх утворення та гідродинамічних явищ в між електродному проміжку. Встановлені аналітичні зв’язки технологічних характеристик процесу чорнової розмірної обробки електричною дугою сплаву ВК8, з режимами обробки і геометричними параметрами. Article is dedicated to the development of technology and equipment of mode of roughing of carbide drawplate by electric arc as an alternative to traditional methods of high performance choice of roughing. During operation, in the hole of drawplate along with uniform abrasion, occurs severe wear, as a consequence of welding of the processed material to the material of drawplate. As a result of the periodic separation of these places the structure obtained by sintering is broken by chipping of the carbide grains. Torn carbide particles leave marks on the wire, with such wear the drawplate does not meet the specified size and it is to bore with larger diameter by the grinding with the diamond tool at the roughing. It is proposed to bore carbide drawplate by dimensional electric arc as at roughing chisel carbide dies dimensional arc of electricity that can take large allowances of material at the lowest time expenditure for processing. At that the machining cycle was down by 4,4-5,2 times. It was made the justifications of the technological scheme of forming of holes of carbide drawplate in the way of sizing by arc taking into account the features of physical formation mechanism and hydrodynamic phenomena in the electrode gap. Analytical roots of technological characteristics of the process of rough sizing with the arc VK8 alloy with treatment regimens and geometrical parameters established.