Збірник наукових праць КНТУ. Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/18
Свідоцтво про державну реєстрацію у Міністерстві юстиції України: серія КВ, №15253-3825 ПР.
Затверджено наказом Міносвіти і науки України № 1528 від 29.12.14р.
ISSN 2409-9392 (Online) 2409-9392(Print)
Мови видання: українська, російська, англійська, періодичність - один раз на рік;
Browse
2 results
Search Results
Item Теоретичне обґрунтування параметрів вібраційного висіву(КНТУ, 2016) Мартиненко, С. А.; Ауліна, Т. М.; Артеменко, Д. Ю.; Martinenko, Sergiy; Aulina, Tetyana; Artemenko, DmitryВ статті розглянуто типи висівних апаратів зернових сівалок. Проаналізовано їх переваги та вади. Запропоновано конструкцію вібраційного висівного апарату та методику первинних розрахунків його основних параметрів – частоти та напряму коливань. Побудовано графік визначення режиму роботи апарату в залежності від цих параметрів. Using of vibrations for the ordinary sowing of seed to this time not used in practice, although simplicity of construction as compared to the pneumatic sowing is obvious. In the article the new construction of oscillation seedmeter is offered and the theoretical calculations of basic his office hours are conducted. Worked out differential equations, describing motion of seed in the process of oscillation motion. On the basis of agrotechnical requirements the parameters of work are expected, namely, frequencies and directions of vibrations, providing the set process of portage of seed. The analysis of different terms of work of vehicle is conducted. As a result was certainly following. On the basis of the conducted theoretical researches certainly parameters and modes of operations of the offered vehicle. The chart of dependence of the mode of operations of sowing oscillation vehicle from correlation of frequency of vibrations of tray and corner of vibration and given recommendations is made in relation to subsequent researches.Item Експериментальні дослідження пневмомеханічного висівного апарата для висіву насіння просапних культур(КНТУ, 2014) Васильковський, О. М.; Абрамова, В. В.; Васильковська, К. В.; Петренко, Д. І.; Vasylkovskiy, Aleksey; Abramova, Viktoria; Vasylkovska, Ekaterina; Petrenko, DmitriyВ статті розглядається серія експериментальних досліджень нового пневмомеханічного висівного апарата для висіву насіння просапних культур. Результати досліджень свідчать про можливість підвищення ефективності точного висіву. The aim is to obtain precise seeding evenly placed on the area of the field plants, which, in this case, have the same area and power developing best. The uniformity of seed placement in the line depends on the uniformity of seed placement on the seed disc, which requires properly orient the seed at the stage of seed capture drive. In order to improve precision seeding cultivated crops at the Department of Agricultural Engineering Kirovograd National Technical University has developed and manufactured a prototype of a new pneumomechanical sowing device, the main feature of which is the presence of extra seed disk that thanks to the original design directs seed to suction hole. Moreover, at suction hole located just one seed. If captures two seed, the second seed is above the upper edge of the extra drive and completely removes unnecessary seeds. In the article the new series of experimental studies pneumomechanical sowing device for sowing seeds of cultivated crops. The research results indicate the possibility of increasing the efficiency of precise seeding. Analysis of response surfaces for fill factor cells of seed disk, to determine the optimal values of the studied factors, namely: value of additional disk thickness should be in the range of 1.4 to 1.6 mm; radius cavity additional disk should be in the range of 3 to 3.2 mm; value of vacuum in the vacuum chamber should be in the range of 2.0 to 2.4 kPa; the rotational speed of the sowing disc cells should be in the range of 0.22 to 0.26 m/s.