Збірник наукових праць КНТУ. Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/18
Свідоцтво про державну реєстрацію у Міністерстві юстиції України: серія КВ, №15253-3825 ПР.
Затверджено наказом Міносвіти і науки України № 1528 від 29.12.14р.
ISSN 2409-9392 (Online) 2409-9392(Print)
Мови видання: українська, російська, англійська, періодичність - один раз на рік;
Browse
11 results
Search Results
Item Аналіз енергетичних характеристик турбомеханізмів(ЦНТУ, 2017) Лобов, В. Й.; Митрофанов, О. В.; Lobov, V.; Mitrofanov, A.Показано, що турбомеханізмиє енергоємними в порівняні з іншими технологічними об’єктами і агрегатами підприємства. Виконано порівняння втрат споживання електричної енергії вентиляторами, використовуючи паспортну номінальну корисну гідравлічну потужність з одної сторони івраховуючи,з іншої сторони,максимальні та мінімальні значення статичних коефіцієнтів корисної дії, статичного тиску та обсяги повітря, що відповідають значенням параметрів вентилятора в точках характеристик. При цьому розрахунок виконано для 25 режимів. Надані результати виконаних розрахунків, які визначають залежність енергоспоживання турбомеханізмами, які залежать від технічних параметрів і режимів роботи та може змінюватися в десятки разів. The purpose of this article is to analyze the characteristics of electrical power of turbo-mechanisms at work in different modes and loads, to establish the power consumption of equipment and find the ways to reduce it. The comparison of electrical power loss consumption of fans using the nameplate nominal effective hydraulic power on the one hand and the maximum and minimum values of the static efficiency coefficient, static pressure and air volume corresponding to the values of fan parameters in the characteristic points on the other hand is carried out. The calculation is performed for 25 modes. The results of the calculations which determine the dependence of turbo-mechanisms energy on technical parameters and operating conditions may ten times vary. To define real power consumption of turbo-mechanisms we should take into account the most rational and possible modes of its operation.To calculate power intensity, defined in the normal turbo-mechanisms operating modes, we must use the minimum and maximum values of static efficiency, static pressure and air volume corresponding to the values of fan parameters performance.In this case we should perform the calculation for the 25 modes.The results of the study prove the dependence of turbo-mechanisms power of technical parameters and operating conditions which may vary by tens of times; therefore, it requires further investigation of equipment automation and devices for its saving.Item Энергетические показатели рабочего процесса высевающих аппаратов и систем(ЦНТУ, 2017) Панков, А. А.; Панков, А. О.; Pankov, A.В статье рассмотрено сравнение энергетических показателей рабочего процесса существующих и перспективных высевающих аппаратов и систем посевных машин. У статті розглянуто порівняння енергетичних показників робочого процесу існуючих та перспективних висівних апаратів і систем посівних машин. The purpose of the research was to establish the nature of the qualitative and quantitative influence of the energy performance of a seed system. Currently, many types of metering systems and energy performance of their work is not completely defined. When creating planting machines main attention is paid to ensure quality of process and performance. At the same time, the current requirements for optimization of energy consumption indicate the need for analysis of the intensity of the working process of the sowing devices. Therefore, in this work the determination and comparison of power to drive the seeding apparatus and systems. Sowing machines and systems require a relatively large amount of power to operate, although the destruction of the ties between the seeds and their movements, active power values can be much smaller.Item Розробка привода для глибокого свердлення методом перехоплення стебла інструмента по його довжині(КНТУ, 2008) Пестунов, В. М.; Свяцький, В. В.; Свяцька, Л. П.Наведені теоретичні і експериментальні дослідження механізмів приводів верстатів для глибокого свердління, що мають проміжні опори. Показано, що застосування пристроїв, що використовують змінну величину вильоту інструмента в процесі обробки глибоких отворів, приводить до збільшення періоду його стійкості. In the article the theoretical and experimental research of mechanisms of machine tools drives for the deep drilling, having intermediate anvil post, are considered. The application of devices with a variable tool extension in deephole machining is bring to a tool durability are demonstrated.Item Розвантаження свердла при комбінованій обробці глибоких отворів(КНТУ, 2008) Пестунов, В. М.; Свяцький, В. В.; Свяцька, Л. П.Наведено схему розвантаження свердла, що основана на використанні комбінованої обробки „різання – пластична деформація”. Спосіб вирішує задачу зниження складових технологічного навантаження і дозволяє розширити технологічні можливості процесу свердління по глибині обробки. The scheme of drill unloading, based on use of the combined processing „cutting – plastic deformation”, is considered. The method solves a problem of technological load components decrease and allows expanding technological capability of drilling process on depth of processing.Item Об эффективности применения пневмомеханического сепаратора корнеклубнеплодов(КНТУ, 2013) Зубков, В. Е.; Zubkov, V.; Зубков, В. Є.В статье аналитическим и экспериментальным способом проведены исследования, подтверждающие эффективность работы пневмомеханического сепаратора корнеклубнеплодов. У статті аналітичним і експериментальним способом проведено дослідження, що підтверджують ефективність роботи пневмомеханічного сепаратора коренебульбоплодів. The aim of this study was to conduct studies to determine the efficiency of the mechanical-air tuberous roots separator. The efficiency application of the separator was evaluated measure of separation effectiveness, which means the share of manual labor, released as a result of the application of the separator. The studies found that the application of the separator enables to reduce 2-3 times the cost of manual labor in the process for separating tuberous roots from impurities.Item Ефективне використання сільськогосподарських угідь в умовах реалізації земельної реформи(КНТУ, 2014) Збаржевецька, Л. Д.; Вдовиченко, Л. В.; Zbarzhevetska, Ludmila; Vdovychenko, LidiaУ статті досліджуються проблеми ефективного використання земельних ресурсів, зокрема, сільськогосподарських угідь. Проаналізовано тенденції показників продуктивності сільськогосподарських угідь, а саме, урожайність та обсяги валової продукції з використанням статистичних методів та визначено тенденції очікуваної врожайності на перспективу. Визначено вплив змін у земельних відносинах на чинники ефективності використання землі. Зазначено чинники впливу на продуктивність земель сільськогосподарського призначення, запропоновано напрями підвищення ефективного використання сільськогосподарських угідь. The main objective of the article is the research of dynamic tendencies of agricultural land productivity indexes and the choice of productivity optimization approaches for the landscapes of agricultural use. The problems of effective use of agricultural landscapes are investigated in the article. The tendencies of yield production and the amount of gross output were analyzed using statistical approaches as well as the tendencies of expected yield production. Influences of various factors of land use were examined and approaches for productivity optimization for the landscapes of agricultural use were suggested. Results of the research showed that the main approach of effective use for the agricultural landscapes is the increasing of yield production, structure improvement of agricultural areas, increase of cultivation of more productive crops and reduced cultivation of less productive crops in a total share, control of violations and gaps in approaches and terms of production of agricultural crops, combining internal and external funds for the equipment provision, technical equipment and the necessary mineral resources following the objective of rapid integration of high-performance technologies.Item Розробка інерційних демпферів коливань виконавчого органу просторової системи приводів та оцінка ефективності їх застосування шляхом математичного моделювання(КНТУ, 2014) Струтинський, С. В.; Strutins'kij, SergeyОбґрунтована необхідність розробки спеціальних демпферів для підвищення показників динамічної якості просторової системи приводів. Наведено розроблені конструкції інерційних демпферів коливань, їх характерні параметри. Для оцінки ефективності застосування демпферів проведено математичне моделювання. Розроблена динамічна модель демпфера, який встановлений на виконавчому органі просторової системи приводів. Складені рівняння динамічної рівноваги та знайдена передавальна функція демпфера. Ефективність демпфера визначена його впливом на зміну максимума квадрата модуля частотної передавальної функції системи. Показано, що застосування демпферів зменшує величину максимума в 2…3 рази. The aim of the research is to increase the quality of spatial dynamic drive systems through the use of specially designed dampers inertial oscillations. The necessity of developing special dampers to improve the dynamic performance as a spatial system drives. Shows developed designs inertial dampers fluctuations, their characteristic parameters. To assess the efficacy of dampers mathematical modeling. Developed a dynamic model of the damper that is mounted on the executive body of the space of reasons. Composite dynamic equilibrium equation and found the transfer function of the damper. The efficiency of the damper its influence to change maximum square modulus of the frequency transfer system functions. It is shown that the use of dampers reduces the value of a maximum of 2 ... 3 times.Item Механізми розвантаження інструменту при свердленні глибоких отворів(КНТУ, 2012) Пестунов, В. М.; Свяцький, В. В.; Придворова, С. В.; Pestunov, V.; Svyatsky, V.; Pridvorova, S.Наведено схеми розвантаження свердла, що основані на використанні комбінованої обробки „різання – пластична деформація” і підведенням мастильно-охолодного технічного засобу з надлишковим тиском. Способи вирішують задачі зниження складових технологічного навантаження і дозволяють розширити технологічні можливості процесу свердління по глибині обробки. The schemes of drill unloading, based on use of the combined processing „cutting – plastic deformation” and admission lubricant-cooling agent with overpressure, are considered. The methods solve a problem of technological load components decrease and allows expanding technological capability of drilling process on depth of processing.Item Оптимізація процесу обробки глибоких отворів(КНТУ, 2012) Пестунов, В. М.; Свяцький, В. В.; Придворова, С. В.; Pestunov, V.; Svyatsky, V.; Pridvorova, S.Наведені теоретичні і експериментальні дослідження механізмів приводів верстатів для обробки глибоких отворів. Показано, що застосування пристроїв із змінною величиною вильоту інструмента, а також механізмів вібраційного свердлення підвищують ефективність обробки глибоких отворів. In the article the theoretical and experimental researches of mechanisms of machine tools drives for the deep drilling are considered. The application of devices with a variable quantity of tool extension, and also mechanisms of vibration drilling raise effectiveness of deep-hole machining are demonstrated.Item Підвищення ефективності процесу обробки глибоких отворів спіральними свердлами(КНТУ, 2009) Пестунов, В. М.; Свяцький, В. В.; Свяцька, Л. П.Наведені теоретичні і експериментальні дослідження механізмів приводів верстатів для обробки глибоких отворів спіральними свердлами. Показано, що застосування пристроїв із змінною величиною вильоту інструмента, а також механізмів вібраційного свердлення підвищують ефективність обробки глибоких отворів. In the article the theoretical and experimental researches of mechanisms of machine tools drives for the deep drilling by means of twist bits are considered. The application of devices with a variable quantity of tool extension, and also mechanisms of vibration drilling raise effectiveness of deep-hole machining are demonstrated.