Збірник наукових праць КНТУ. Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/18
Свідоцтво про державну реєстрацію у Міністерстві юстиції України: серія КВ, №15253-3825 ПР.
Затверджено наказом Міносвіти і науки України № 1528 від 29.12.14р.
ISSN 2409-9392 (Online) 2409-9392(Print)
Мови видання: українська, російська, англійська, періодичність - один раз на рік;
Browse
4 results
Search Results
Item Аналіз теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса(ЦНТУ, 2017) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Красота, М. В.; Руденко, Т. В.; Kuleshkov, Y.; Magonets, E.; Kuleshkova, K.; Krasota, M.; Rudenko, T.В статті наведені результати аналізу теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса. Встановлені теоретичні залежності об’єму відсіченої порожнини від параметрів зубчастого зачеплення, а також від положення точки зачеплення на лінії зачеплення шестерень насоса. Отримані теоретичні залежності дозволяють визначити геометричні параметри відсіченої порожнини, при яких виключається явище компресії робочої рідини. Виключення компресії досягнуто завдяки використанню зубчастого зачеплення з асиметричною лінією зачеплення. В роботі вказані недоліки існуючих теоретичних досліджень і вказані напрямки подальшого їх розвитку.The objective of research is to analyze scientific and technical information on the results of theoretical studies of the geometric parameters of the cut-off housing of the gear pump and to determine future direction of research of the processes that take place in the cut-off housing and to formulate the scientific hypothesis of the research. The article presents the results of the analysis of theoretical studies of geometric parameters of the cut-off housing of the gear pump. The theoretical dependences of the volume of the housing on the parameters of toothing were established as well as the position of the point of engagement on the line of contact of a gear pump. The theoretical dependences allow determining geometrical parameters of the cut-off housing which eliminate the phenomenon of the working fluid compression. The avoidance of compression is achieved through the use of toothing with asymmetrical engagement line. The work indicates the shortcomings of existing theoretical research and presents the directions of further development. It was established that one of the possible ways to reduce the impact of the compression of the working fluid in the cut-ff housing is to use toothing with asymmetric line engagement.Item Математична модель втрат робочої рідини через радіальний зазор шестеренного насоса типу НШ(КНТУ, 2005) Матвієнко, О. О.; Matvienko, OleksandrВ статті розглянуто змінний характер величини зони ущільнення радіального зазору шестеренного насоса типу НШ і на основі отриманих результатів створено математичну модель втрат робочої рідини через радіальний зазор. There is analysis variable parameter of compaction area of radial clearance in gear pumps of НШ-type. The author of the article derive the simulator for calculation a radial leak on the basis of findings.Item Аналіз існуючих уявлень про механізм виникнення пульсацій миттєвої подачі шестеренного насоса(КНТУ, 2014) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Осін, Р. А.; Кулєшкова, К. Ю.; Kuleshkov, Yuriy; Rudenko, Tymofiy; Krasota, Mykhailo; Osin, Ruslan; Kuleshkova, KseniaВ статті наведені теоретичні дослідження спрямовані на розробку фізичної моделі та відповідної їй аналітичної залежності миттєвої подачі, що дозволяють пояснити причини і механізм пульсації миттєвої подачі шестеренного насоса. The objective of the research is the elaboration of a mathematical physical model of immediate flow of a gear pump which allows explaining the mechanism of occurrence of pulsations of immediate flow and pressure in the process of work cycle of a gear pump. We suggested a new physical model and a corresponding mathematical model of the process of immediate flow of a gear pump which show that the process of flow consists of two simultaneously occurring processes: the process of volume reduction which stimulates flow and the process of volume increase which blocks flow. The suggested mathematical model allows explaining the pulsating character of immediate flow of a gear pump due to the peculiarities of changes of conditional radiuses which connect the centres of gears with the contact point and while rotation they block the flow.Item Экспериментальные исследования спектров шума шестеренного насоса с косозубым зацеплением(КНТУ, 2015) Кулешков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Матвиенко, О. О.; Осин, Р. А.; Kuleshkov, Y.; Rudenko, T.; Krasota, M.; Matvienko, O.; Osin, R.; Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Матвієнко, О. О.; Осін, Р. А.В статье приведены результаты испытаний шумовых характеристик экспериментального шестеренного насоса с косозубым зацеплением. Исследованы уровни звука, спектры шума. экспериментального насоса с косозубым зацеплением, а также серийного насоса аналогичного типоразмера при разных режимах их работы. Выполнен сравнительный анализ шумовых характеристик насосов при разных нагрузках с целью оценки эффективности использования косозубых зацеплений в шестеренных насосах с точки зрения снижения шума. В статті наведені результати випробовувань шумових характеристик експериментального шестеренного насоса з косозубим зачепленням. Досліджено рівні звуку, спектри шуму експериментального шестеренного з косозубим зачепленням, а також серійного насосу аналогічного типорозміру при різних режимах їх роботи. Виконано порівняльний аналіз шумових характеристик насосів при різних навантаженнях з метою оцінки ефективності використання косозубих зачеплень в шестеренних насосах з точки зору зниження шуму. The objective of the work is the experimental testing of the noise level by the lines of spectrum of the experimental gear pump with helical toothing and the comparison with the noise level of a serial pump. The article presents the results of tests of noise characteristics of the experimental gear pump with helical toothing. The levels of noise, noise spectrums of the experimental gear pump with helical toothing and a serial pump of the analogical size with straight toothing were investigated using different operating modes. The comparative analysis of noise characteristics of the pumps under different load was carried out in order to estimate the efficiency of using helical toothing in gear pumps from the point of view of noise reduction. Experiments of the noise level of a gear pump with helical toothing showed that with the increase of pressure of hydraulic fluid the level of noise slowly increases from 1,5 to 6 dB depending on speed mode. The highest noise level of a pump with helical toothing (91,5 dB ) is noticed under the pressure of 16,0 MPa and rotation frequency n=2400 revolutions per minute. The comparative analysis of the experimental pump and a serial pump enables to state that the noise level of the experimental pump is lower in all operating modes compared to the serial pump. During tests it was marked that the noise level of the stand which is a barrier is quite high and under some operating modes it is close to the noise level of the experimental pump on the stand.