Випускні кваліфікаційні роботи
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/763
Browse
Search Results
Item Прогнозування експлуатаційних характеристик спіральних свердел малих діаметрів(ЦНТУ, 2024-06-30) Іщенко, Віталій Сергійович; Ishchenko, VitaliiМетою дослідження є збільшення довговічності і надійності різального інструменту при свердлінні малих діаметрів через прогнозування експлуатаційних характеристик. Проведено аналіз методів і способів підвищення точності обробки отворів та розрахунків раціональних режимів обробки при заданих параметрах свердла для обґрунтованого прогнозування стійкості різального інструменту. Шляхом теоретичних досліджень з’ясовано вплив умов різання, матеріалу властивостей матеріалу, діаметра свердла і геометрії свердла на період стійкості при свердленні. Прогнозування зносу інструменту під час свердління виконувалося за допомогою аналітичної моделі Такеяма-Мурата та оновлення геометрії різального інструменту під час процесу формування стружки. Запропоновано алгоритм розрахунку прогнозування експлуатаційних характеристик спіральних свердел. The purpose of the study is to increase the durability and reliability of the cutting tool when drilling small diameters through the prediction of operational characteristics. An analysis of methods and ways of improving the accuracy of hole processing and calculations of rational processing modes at given parameters of the drill for reasonable forecasting of the stability of the cutting tool was carried out. The effect of cutting conditions, material, material properties, drill diameter, and drill geometry on the period of stability during drilling was determined through theoretical studies. Prediction of tool wear during drilling was performed using the Takeyama-Murat analytical model and updating the geometry of the cutting tool during the chip formation process. An algorithm for calculating the forecasting of the operational characteristics of spiral drills is proposed.Item Підвищення ефективності механічної обробки наскрізних отворів(ЦНТУ, 2024-06-30) Зотов, Родіон Анатолійович; Zotov, RodionМетою дослідження є збільшення довговічності і надійності різального інструменту при свердлінні. Розглянуті різні варіанти конструкції свердел для обробки вуглепластиків, проведено дослідження геометричних параметрів обраної конструкції інструменту та спосібів заточки різальної кромки. За допомогою моделювання інструментальної поверхні у середовищі AutoDesk Inventor розроблена 3D модель спірального свердла. Проведено дослідження впливу установчих параметрів на профіль вихідної інструментальної поверхні. Шляхом теоретичних досліджень з’ясовано вплив факторів зменшення точності отворів, вплив швидкості, властивостей матеріалу, діаметра свердла, подачі та температури різання при обробці точних наскрізних отворів. Запропоновано для підвищення точності обробки наскрізних отворів в полімерних композиційних матеріалах схему різання із зміною подач. The purpose of the study is to increase the durability and reliability of the cutting tool when drilling. Various options for the design of drills for processing carbon plastics are considered, the geometric parameters of the selected tool design and ways of sharpening the cutting edge are studied. A 3D model of a spiral drill was developed using tool surface modeling in the AutoDesk Inventor environment. The influence of setting parameters on the profile of the initial tool surface was studied. Through theoretical studies, the influence of factors reducing the accuracy of holes, the influence of speed, material properties, drill diameter, feed and cutting temperature during the processing of precise through holes has been clarified. To increase the accuracy of processing through holes in polymer composite materials, a cutting scheme with a change in feed is proposed.Item Комп’ютерне моделювання операції обжиму товстостінних трубних заготовок(ЦНТУ, 2024-01-30) Бєлов, Віталій Жанович; Bielov, VitaliyyМетою дослідження є дослідження операції обжиму товстостінних трубних заготовок на основі аналізу напружено-деформованого стану заготовки при пластичній формозміні для обгрунтованого вибору основних технологічних параметрів процесу деформування. Проведено аналіз процесу обжиму товстостінних трубних заготовок та особливостей існуючих методів отримання таких виробів. Визначена математична модель обжиму трубної анізотропічної заготовки вісесиметричним конічним пуансоном. Проведено чисельне моделювання обжиму трубної анізотропічної заготовки вісесиметричним конічним пуансоном. Проведено графічний аналіз оцінки впливу технологічних параметрів, кута конусності пуансона, умов тертя на контактній поверхні робочого інструмента і заготовки, анізотропії механічних властивостей заготовки на напружений і деформований стан, силові режими і граничні можливості формозміни операції обжиму товстостінних трубних заготовок. За допомогою комп’ютерного моделювання в програмному комплексі DEFORM 2D/3D проведено аналіз операційного переходу технологічного процесу обжиму товстостінних трубних заготовок. The purpose of the study is to study the operation of crimping thick-walled pipe blanks based on the analysis of the stress-strain state of the blank during plastic deformation for a reasonable choice of the main technological parameters of the deformation process. An analysis of the process of crimping thick-walled pipe blanks and features of the existing methods of obtaining such products was carried out. The mathematical model of the crimping of the pipe anisotropic workpiece with an axisymmetric conical punch is determined. Numerical modeling of the crimping of an anisotropic pipe blank with an axisymmetric conical punch was carried out. A graphical analysis of the influence of technological parameters, the taper angle of the punch, the conditions of friction on the contact surface of the working tool and the workpiece, the anisotropy of the mechanical properties of the workpiece on the stressed and deformed state, force modes and the limit possibilities of the shape change of the crimping operation of thick-walled pipe blanks was carried out. With the help of computer modeling in the DEFORM 2D/3D software complex, an analysis of the operational transition of the technological process of crimping thick-walled pipe blanks was carried out.