Випускні кваліфікаційні роботи
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/763
Browse
Search Results
Item Моделювання силової взаємодії штампового інструменту і обладнання під час здійснення технологічної операції(ЦНТУ, 2024-01-29) Локоцький, Костянтин Анатолійович; Lokotskyi, KostiantynМетою дослідження є підвищення якості листового штампування шляхом удосконалення пристроїв компенсації системи «прес-штамп. Виконано експериментальне дослідження напружено-деформованого стану штампа під дією технологічного зусилля і різних варіантах його закріплення і налагодження. Встановлено, що найменший вигин пуансону відбувається при закріплені нижньої частини штампу на пристрої компенсації, який використовується замість підштампової плити. Оптимальний діапазон рухомості компенсатора між його рухомими і нерухомими елементами визначена при зазорі 1 мм. Виконано моделювання напружено-деформованого стану окремих компонентів компенсатора похибок системи “прес-штамп” методом кінцевих елементів в розрахунковому пакеті Simulation САПР SolidWorks для преса 0,4 МН в умовах його номінального зусилля. Встановлено, що прогин та напруження нижньої нерухомої плити компенсатора з підп’ятником, при номінальному зусиллі навантаження преса, значно більші ніж на підштамповій плиті преса. Розроблено технічні рішення по модернізації компенсатора похибок системи "прес-штамп". Запропоновано спосіб зменшення прогину нижньої нерухомої плити компенсатора над провальним фігурним отвором в столі преса, шляхом накладення в зону інтенсивних деформацій зустрічного зусилля підпору. The aim of the research is to improve the quality of sheet metal stamping by enhancing the devices of the "press-stamp" compensation system. An experimental study of the stress-strain state of the stamp under the influence of technological forces and various options for its fixation and adjustment has been conducted. It was found that the smallest deflection of the punch occurs when the lower part of the stamp is fixed on the compensation device, which is used instead of the press plate. The optimal range of compensator mobility between its moving and fixed elements is determined at a gap of 1 mm. Modeling of the stress-strain state of individual components of the compensator errors in the "press-stamp" system was performed using the finite element method in the Simulation CAD SolidWorks package for a press with a nominal force of 0.4 MN under its nominal load conditions. It is established that the deflection and stress on the lower fixed plate of the compensator with a heel, under the nominal load of the press, are significantly higher than on the press plate.Technical solutions for modernizing the compensator of the "press-stamp" system errors have been developed. A method of reducing the deflection of the lower fixed plate of the compensator above the punch hole in the press table is proposed by applying counterforce in the zone of intense deformations.Item Дослідження особливостей проєктування і конструювання фундаментів висотних будівель(ЦНТУ, 2024) Ткаченко, Володимир Сергійович; Tkachenko, VolodymyrМагістерська робота ґрунтується на результатах експериментальних лабораторних досліджень, що виконані В.В. Ковба, та спрямована на огляд, аналіз, узагальнення інформації та власну інтерпретацію щодо урахування ефекту виникнення «від’ємного тертя» при традиційному способі навантаження пальово-розтвіркового фундаменту висотних будівель. В роботі виконано огляд і логічне обґрунтування щодо нормативного забезпечення на етапах проектування, будівництва та експлуатації висотних будівель. Також виконано огляд та глибокий аналіз результатів експериментальних лабораторних досліджень щодо встановлення геотехнічно можливих способів, конструктивних і технологічних особливостей передачі навантаження від висотної будівлі через класичні елементи пальового фундаменту. Описано стендове, лабораторне експериментальне обладнання для проведення експерименту даного напрямку. The master's thesis is based on the results of experimental laboratory studies performed by V.V. Kovba, and is aimed at the review, analysis, generalization of information and own interpretation regarding the consideration of the effect of "negative friction" in the traditional method of loading the pile-slotted foundation of high-rise buildings. The work includes an overview and logical justification of regulatory support at the stages of design, construction and operation of high-rise buildings. Also, a review and in-depth analysis of the results of experimental laboratory studies on establishing geotechnically possible methods, structural and technological features of load transfer from a high-rise building through classical elements of a pile foundation was performed. Bench, laboratory experimental equipment for carrying out experiments in this direction is described.