Центральноукраїнський науковий вісник. Технічні науки.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/9042
Ідентифікатор медіа: R30-03350 (рішення Національної ради України від 25.04.2024 р. № 1418).
ISSN 2664-262X (p)
DOI: 10.32515/2664-262X
Browse
3 results
Search Results
Item Математична модель верхнього робочого елемента механічно-пневматичного збирача комах-шкідників пасльонових культур(ЦНТУ, 2024) Онопа, В. В.; Артеменко, Д. Ю.; Кислун, О. А.; Онопа, В. А.; Onopa, V.; Artemenko, D.; Kyslun, O.; Onopa, V.В роботі наведені результати пошукових теоретичних досліджень конструктивних особливостей верхнього робочого елементу пристрою для механічно-пневматичного збирання комах-шкідників пасльонових культур. Під час аналізу наукових джерел було встановлено, що комахи-шкідники значною мірою призводять до серйозних втрат у світовому виробництві сільськогосподарської продукції. Пестицидний обробіток є основним методом боротьби з ними, проте така практика призводить до забруднення навколишнього середовища, загрози здоров'ю людини та підвищення ризику захворювань. У зв'язку з цим велика увага приділяється розробці екологічно безпечних методів боротьби. Виявлено, що одним з найбільш ефективних методів є фізичне збирання комах-шкідників пристроями різної дії. Тому подальша розробка нових конструкцій пристроїв для виконання процесу збирання комах шкідників є актуальною задачею. З цією метою був запропонований новий пристрій для збирання комах-шкідників, призначений для ефективного збирання шкідників пасльонових культур за допомогою механічнопневматичного методу. Теоретично обґрунтована конструкція верхнього робочого елемента пристрою для збирання комах-шкідників і встановлено, що кут атаки робочої поверхні пристрою лежить в межах від 10 до 60°. Ефективність запропонованої конструкції нового пристрою забезпечується підвищеним впливом механічної дії на рослину пасльонових культур без її ушкодження і виключенням втримання шкідника на всіх рівнях по висоті рослини, максимальним збиранням шкідників за один прохід пристрою. The paper presents the results of exploratory theoretical studies of the design features of the upper working element of the device for the mechanical-pneumatic collection of insect pests of nightshade crops. During the analysis of scientific sources, it was established that insect pests to a large extent lead to serious losses in the world production of agricultural products. Pesticide treatment is the main method of combating them, but this practice leads to environmental pollution, threats to human health and increased risk of diseases. In this regard, great attention is paid to the development of ecologically safe methods of control. It was found that one of the most effective methods is the physical collection of insect pests with devices of various effects. Therefore, the further development of new designs of devices for carrying out the process of collecting insect pests is an urgent task.Item ІТ в процесах створення та експлуатації об’єктів будівництва(ЦНТУ, 2020) Кислун, О. А.; Пархоменко, Ю. М.; Скриннік, І. О.; Дарієнко, В. В.; Kyslun, O.; Parhomenko, Yu.; Skrynnik, I.; Dariienko, V.; Скринник, И. А.; Дариенко, В. В.У статті представлено результати дослідження ІТ в процесах створення та експлуатації об’єктів будівництва. Подано огляд засобів комплексної автоматизації обліку в Україні. Проведено огляд ринку засобів автоматизованого проектування для архітектури та будівництва, наведено їх характеристики. Представлено огляд систем комплексного керування організацією ринку України. The article presents the results of IT research in the processes of creation and operation of construction projects. An overview of the means of complex accounting automation in Ukraine is given. An overview of the market of computer-aided design tools for architecture and construction is given also their characteristics are given. An overview of integrated market management systems in Ukraine is presented. The field of application of information technologies is constantly expanding, and growing constantly require monitoring of new implementations and search for effective innovations. Awareness provides a competitive advantage for both the developer and the consumer. Thus, the task of IT monitoring arises, and in the presence of a common area of interest, a team of like-minded people faces the problem of IT research in the processes of creation and operation of construction projects. IT in the process of creating and operating construction projects is used in all life cycles of the latter. The software that serves these processes is diverse and mostly disparate and is a set of software products aimed at sectoral use [1]. The issue of introduction of modern IT in this area is relevant and there is a need for development by specialists, which requires their study. The software used can generally be divided into: general purpose software; specialized accounting programs and other accounting systems; computer-aided design systems; integrated management systems of the organization; building management systems; scheduling systems. The so-called specialized accounting programs and accounting systems presented on the Ukrainian market in the construction sector are the same as for other sectors of the economy, there are only certain adaptations to take into account the specifics of the scope. At this stage of economic development of Ukraine in the construction industry ERP systems have not yet become widespread. Building management systems are also waiting to be expanded in Ukraine. В статье представлены результаты исследований ИТ в процессах создания и эксплуатации объектов строительства. Подан обзор средств комплексной автоматизации учета в Украине. Проведен обзор рынка средств автоматизированного проектирования для архитектуры и строительства, наведены их характеристики. Представлен обзор систем комплексного управления организацией рынка Украины.Item Дослідження кутових переміщень платформи МПС із ріжучим інструментом(ЦНТУ, 2020) Павленко, I. I.; Годунко, М. О.; Кислун, О. А.; Костюк, Є. С.; Pavlenko, I.; Hodunko, M.; Kyslun, O.; Kostyuk, E.; Павленко, И. И.; Костюк, Е. С.В статті виконано аналітичний розрахунок величини переміщення виконавчого органу верстата з механізмом паралельної структури (МПС) по лініям в поперечному напрямку під кутом. Досліджено вплив конструктивних параметрів МПС на значення цих переміщень виконавчого органу. For the manufacture of parts of complex shapes, it becomes necessary to move the cutting tool along the line at a certain angle. For this, machines equipped with mechanisms of parallel structure are used. Only a study of the movable capabilities of these mechanisms makes it possible to introduce them into production. The studies focus on the transverse movement of the center of the moving platform of the parallel structure mechanism for a hexapod machine, as a material point moving along a line depending on the angle of contact of the tool and the perpendicular to the plane of the work surface (axis of symmetry of the mechanism). To determine the possible positions of the center of the moving platform, we consider a generalized scheme of the parallel structure mechanism. Given the restrictions on movement, the area of possible positions is divided into zones: Zrp - without a cutting tool; Zri - the zone of positions of the top of the instrument. The part that is being processed is installed on the technological device, which is placed on the basis of a parallel structure mechanism. Parameters of a machine with a parallel structure mechanism: a, b - distance between the supports of the stationary carrier system and the executive body, respectively; Lmax is the maximum length of the kinematic links; lmin is the minimum length of the kinematic links; li is the current length of the kinematic links; l is the magnitude of the transverse movement; φ is the angle of inclination of the executive body; hi is the current position of the executive body of the mechanism of the parallel structure in height. The assessment of motor capabilities is determined by the displacement index, which is the ratio of the actual displacement value l to the theoretically possible one (taken equal to the maximum rod length Lmax). From the above dependencies it is seen that the influence of the motor capabilities of the rods on the relative displacement provides an increase in the displacement index in the indicator section from 0.45 to 0.65, then the section that is affected by the slope of the displacement line, with a decrease in which the displacement in the area of0.8 up to 1 movement decreases again, this is due to the complex geometry of the service area ofthe working space of the machine with a parallel structure mechanism. On the effect of the ratio of the sizes of the movable to the fixed platform on the relative displacement, we have that with an increase in the indicator, the initial indicator of the relative displacement also increases, with a value of the exponent n starting from 0.6 its value decreases in all cases. The influence of the ratio of the maximum displacement of the rods to the size of the fixed platform, on the relative displacement has the opposite of the previous character. With an increase in the indicator m, the relative displacement indicator increases, with a further increase in the indicator m, it can be seen that significantly decreases the displacement indicator and with a value less than 0.6. В статье выполнен аналитический расчет величины перемещения исполнительного органа станка с механизмом параллельной структуры (МПС), по линиям в поперечном направлении под углом. Исследовано влияние конструктивных параметров МПС на значение этих перемещений исполнительного органа.