Центральноукраїнський науковий вісник. Технічні науки.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/9042
Ідентифікатор медіа: R30-03350 (рішення Національної ради України від 25.04.2024 р. № 1418).
ISSN 2664-262X (p)
DOI: 10.32515/2664-262X
Browse
3 results
Search Results
Item Обґрунтування ефективності та класифікація компонентів технологічних середовищ для фінішної антифрикційної безабразивної обробки деталей машин(ЦНТУ, 2024) Красота, А. М.; Шепеленко, І. В.; Красота, М. В.; Осін, Р. А.; Krasota, А.; Shepelenko, І.; Krasota, М.; Osin, R.В роботі виконана систематизація існуючих уявлень про функції та призначення окремих компонентів технологічних середовищ для фінішної антифрикційної безабразивної обробки деталей. Визначено роль компонентів технологічного середовища, також їх вплив на процес формування антифрикційних покриттів. Проаналізовані хімічні механізми реакцій, що відбуваються під час фінішної антифрикційної безабразивної обробки деталі. The goal of this research is the determination of selection of technological medium components for finishing antifriction non-abrasive treatment to ensure high-quality of coating. The research offers a systematization of existing apprehensions of functions and purposes of separate technological mediums components for finishing antifrictional non-abrasive treatment of parts. Was determined the role of technological mediums components and their influence on the finishing antifrictional non-abrasive treatment process. Were analyzed chemical reactions mechanisms occuring during finishing antifrictional nonabrasive treatment of a part.Item Пошук оптимальних параметрів фінішної антифрикційної безабразивної обробки гільз циліндрів автотракторних двигунів(ЦНТУ, 2023) Шепеленко, І. В.; Черновол, М. І.; Лещенко, С. М.; Красота, М. В.; Немировський, Я. Б.; Шумляківський, В. П.; Shepelenko, І.; Chernovol, М.; Leshchenko, S.; Krasota, M.; Nemyrovskyi, Ya.; Shumliakivsky, V.В роботі представлені результати досліджень, які спрямовані на підвищення якості отримання антифрикційних покриттів при використанні фінішної антифрикційної безабразивної обробки гільз циліндрів автомобільних і тракторних двигунів. За показники якості антифрикційного покриття обрано його суцільність, шорсткість поверхні та масоперенесення антифрикційного матеріалу. Параметрами оптимізації є основні режими фінішної антифрикційної безабразивної обробки, а також геометричні характеристики вихідної поверхні, шо обробляється. В результаті реалізації багатофакторного експерименту отримані статистичні моделі, що дають можливість оцінити вплив досліджувальних факторів на критерії оптимізації. Аналіз математичних моделей дозволив визначити оптимальні варіанти поєднання технологічних факторів, що забезпечують якість покриття, а також встановити раціональні значення режимів фінішної антифрикційної безабразивної обробки та геометричних характеристик вихідної поверхні. This paper presents the results of research aimed at improving the quality of antifriction coatings obtained by finishing antifriction non-abrasive treatment (FANT). It has been previously established that the formation of an antifriction coating during FANT largely depends on the technological parameters that determine the conditions of contact between the tool and the surface being treated. The study of the peculiarities of surface contact, their regularities, as well as the main parameters of the FANT process, makes it possible to improve the quality of the antifriction coating, and therefore the operational properties of the part.Item Системний підхід до формування показників якості відновлених деталей(ЦНТУ, 2023) Черновол, М. І.; Шепеленко, І. В.; Chernovol, М.; Shepelenko, І.В роботі розглянуто технологічний процес відновлення деталей як систему взаємопов’язаних елементів, які можуть впливати на формування показників якості відновлених деталей. На етапі технологічного проектування виокремлені основні ієрархічні рівні, а технологічний процес відновлення в цілому представлений у вигляді функцій зв’язків між окремими елементами підсистеми. Це дозволило представити загальну структуру технологічного процесу відновлення зношених деталей як систему взаємозв’язків. З урахуванням особливостей функціонування системи запропоновано підхід, відповідно до якого всі елементи системи мають вплив до формування показників якості відновлених деталей. Встановлено функціональні зв’язки між показниками якості та елементами технологічного процесу на різних рівнях оцінювання. Показано шляхи забезпечення якості відновлених деталей на основних етапах життєвого циклу виробу. The paper considers the technological process of parts restoration as a system of interrelated elements that can influence the formation of quality indicators of restored parts. It is established that the technological process has all the necessary properties that are required for systems. However, modern methods and criteria used in the design of the technological process of parts recovery focus on the selection of the optimal recovery method, which is only part of the technological process. Therefore, the paper sets the goal of presenting the technological process of restoration as a system of interconnections between individual elements that allow to purposefully influence the quality indicators of restored parts. The main hierarchical levels of technological design of part recovery are defined. In turn, the technological process of restoration as a whole is presented in the form of functions of connections between individual elements of the subsystem. This made it possible to present the overall structure of the technological process of restoring worn parts as a system. Taking into account the peculiarities of the system's functioning, an approach is proposed, according to which all elements of the system have an impact on the formation of quality indicators of the restored parts. The functional links between quality indicators and elements of the technological process at different levels of evaluation are established. The main ways to ensure the required quality indicators through the elements of the technological process are determined: methods, equipment, materials, modes, equipment, etc. The proposed approach to the formation of quality indicators of remanufactured parts makes it possible to study the cause-and-effect relationships between the parameters of technological processes and quality indicators of remanufactured parts, as well as to establish ways to improve them. The ways to ensure the quality of remanufactured parts at the main stages of the product life cycle are shown.