Центральноукраїнський науковий вісник. Технічні науки.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/9042
Ідентифікатор медіа: R30-03350 (рішення Національної ради України від 25.04.2024 р. № 1418).
ISSN 2664-262X (p)
DOI: 10.32515/2664-262X
Browse
2 results
Search Results
Item Чисельне моделювання пружного гістерезису сипкого матеріалу(ЦНТУ, 2023) Івлєв, В. В.; Ivliev, V.В результаті чисельного моделювання процесу деформації сипкого матеріалу (на прикладі зернового матеріалу) отримані рівняння регресії другого порядку залежностей площі петлі пружного гістерезису і максимального значення сили при 25 % відносній деформації зернового матеріалу від його фізико-механічних властивостей (щільність, коефіцієнт Пуассона і модуль Юнга). Представлені результати можуть бути використані при подальшому моделюванні або при створені фізико-математичних моделей процесу стискання зернового матеріалу в грануляторах, екструдерах та експандерах. The elastic hysteresis of bulk material is an important problem in many fields of science and technology, including mining and metallurgy, construction, energy, and engineering. This is due to the fact that loose materials consist of a large number of particles that can shift relative to each other under the influence of external loads. This process is accompanied by energy losses and changes in the shape of the material structure, which in turn leads to elastic hysteresis. Knowledge of material behavior under various loading conditions is essential for developing safe and effective engineering solutions. The purpose of the research is to determine the parameters of the deformation of loose material (for example, granular material) depending on its physical and mechanical properties in the Simcenter STAR-CCM+ software package. The elastic hysteresis loop reflects the behavior of the material under cyclic loading, when strain and stress changes occur. Loop area is a measure of material energy losses that occur during cyclic loading. As a result of numerical modeling of the process of deformation of loose material (on the example of granular material), the regression equations of the second order of the dependences of the area of the elastic hysteresis loop and the maximum force value at 25% relative deformation of the granular material from its physical and mechanical properties (density, Poisson's ratio and Young's modulus) were obtained. The presented results can be used in further modeling or in the creation of physico-mathematical models of the process of compression of grain material in granulators, extruders and expanders.Item Теоретичне дослідження руху сипкого матеріалу в постачальному пристрої установок безперервної дії(ЦНТУ, 2019) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Орышака, О. В.; Гуцул, В. И.; Артюхов, А. Н.; Oryshaka, O.; Gutsul, V.; Artiuhov, A.Отримані залежності швидкості руху сипкого матеріалу в постачальному пристрої установок безперервної дії від геометричних параметрів постачального пристрою, а також визначено діапазон зміни швидкості руху сипкого матеріалу в постачальному пристрої. Полученны зависимости скорости истечения сыпучего материала в подающем устройстве установок непрерывного действия от геометрических параметров питающего устройства, а также определён диапазон изменения скорости истечения сыпучего материала в подающем устройстве. Continuous-action plants have several advantages over cycle-feed units (low energy costs, high productivity, lower material consumption, etc.), so improving continuous-action installations is an urgent task. The bulk material feeder, as an integral part of the continuous-action plants, requires appropriate research to substantiate and optimize the design parameters of the installation. The purpose of this work is to investigate the influence of the geometrical parameters of the stabilizing slope of the delivery devices of the continuous-action installations for loading free-flowing materials on the speed of movement of the bulk material and, thus, the technological process of the installation for loading bulk materials. The dependences of the velocity of the free-flowing material in the delivery device of the continuous devices on the geometric parameters of the supply device are determined, as well as the range of velocity variation of the bulk material movement in the feed device is determined. Research findings. The velocity of loose material increases with increasing radius r (fig. 3) and angle (fig. 2). The range of variation in speed (variability, boundary limits) of the velocity of free-flowing material in the supplying device is determined. At , the velocity of the free-flowing material varies between 2,11 ... 2,3 m / s. The obtained results allow to determine the values of the main geometric parameters of the supply device of the continuous devices to provide the required output indicators The results obtained allow us to determine the values of the basic geometric parameters of the stabilizing slope of the delivery devices of the continuous operation installations to provide the required output indicators.