Конструювання, виробництво та експлуатація сільськогосподарських машин. Випуск 45. Ч. 1 - 2015
Permanent URI for this collectionhttps://dspace.kntu.kr.ua/handle/123456789/2008
Browse
Search Results
Item Механіко-технологічні передумови зменшення втрат маси коренеплодів в процесі їх збирання(КНТУ, 2015) Адамчук, В. В.; Борис, А. М.; Булгаков, В. М.; Борис, М. М.; Adamchuk, V.; Borys, А.; Bulgakov, V.; Borys, M.Метою досліджень є зменшення втрат цукроносної маси в процесі відділення гички цукрових буряків від головок коренеплодів. В результаті експериментального дослідження розподілення висоти виступання головок коренеплодів над поверхнею ґрунту підтверджена гіпотеза про те, що воно не заперечує закону нормального розподілення. По результатах проведених вимірювань встановлені межі змін його статистичних характеристик, які мають наступні значення: середньостатистичне відхилення σ = 20...30 мм, математичне сподівання m = 40...60 мм. Розроблена лабораторна установка і проведені на ній експериментальні дослідження дали всі основи для розроблення нової системи автоматичного корегування висоти зрізу гички на коренезбиральних машинах сучасного технічного рівня. The experimental results and performance testing process sugar beet conducted in recent years have shown that the beet modern machines that were produced in Europe and America, working with significant losses on sugar mass. These losses are due to generally poor quality cut tops with bits of sugar beet in the bud. Therefore, now is the urgent search for technical solutions that will avoid these losses. The purpose of research is to reduce the losses of sugar supply in the process of separating the tops of the heads of sugar beet roots. As a result of the experimental investigation of the distribution of height protruding heads of root crops above the ground confirmed the hypothesis that it can not deny the law of normal distribution. The results of the measurements set limits changes in its statistical characteristics, which are as follows: average statistical deviation σ = 20 ... 30 mm, the expectation m = 40 ... 60 mm. Designed and conducted laboratory setting her experimental studies have every reason to develop a new system of automatic cor.Item Модифікуючий вплив присадок на термін заміни моторної оливи в нестаціонарних умовах експлуатації(КНТУ, 2015) Слонь, В. В.; Slon', ViktorРозглянута проблема підвищення надійності транспортних засобів, що працюють в нестаціонарних умовах експлуатації та вплив режимів їх роботи на термін заміни моторної оливи. Охарактеризовано вплив зміни властивостей моторної оливи на її показники якості. Наведені результати експериментальних досліджень впливу модифікування моторної оливи присадками дисульфід молібдену, "Roil Gold", "КГМТ-1" на швидкість надходження та концентрацію заліза з напрацюванням. Виявлено поліпшення показників якості моторної оливи і подовження терміну її експлуатації. The aim of this work is to study the impact modifying additives to change the speed of receipt and concentration of iron in the motor oil, vehicle operating in non-stationary conditions. The problem of improving the reliability of vehicles operating in non-stationary conditions and the impact of their operation modes for up replacing the engine oil. The characteristic types of unsteady operating conditions, depending on the environmental conditions, climate, traffic, mining conditions, operating conditions, are defined by their main parameters. Demonstrated techniques for obtaining and processing the results of experimental studies. The influence of changes in the properties of motor oil in its quality and condition of engine oil determined by the contents of her metal wear products, by method sprektrografii. The results of experimental studies of the effect of modification of motor oil additives molybdenum disulfide, "Roil Gold", "КГМТ-1" to speed receipt and concentration of iron and operating time of diesel vehicles. Found improvement in the quality of motor oil and the extension of its operation.Item Обробка електричною дугою матриць для брикетування(КНТУ, 2015) Сіса, О. Ф.; Sisa, OlehВиконано обґрунтування технологічної схеми формоутворення бічних поверхонь утвору матриць для брикетування способом розмірної обробки електричною дугою з урахуванням особливостей фізичних механізмів їх утворення та гідродинамічних явищ в міжелектродному проміжку. Встановлені аналітичні зв’язки технологічних характеристик процесу розмірної обробки електричною дугою сталі Х12МФ з режимами обробки і геометричними параметрами. The article is dedicated to the development of technology and equipment method of packing dies processing with dimensional electric arc as high-performance alternative to traditional methods of processing. Fuel briquettes are formed by pressing force with the pressure up to 500 kN of pre-shredded waste wood and plant in the hole of matrix, where the process of aggregation goes. In the development of equipment and tools it is necessary to take into account the conditions that will ensure the formation of fuel briquettes. The most important parameter for pressing fuel briquettes is the energy which corresponds to the work of frictional forces against the walls of the die hole, since the pressure force transmitted to the side surface, is proportional to pressure in the longitudinal direction. The optimal parameter of the walls of the die hole is the roughness Ra = 3,2..6,3 mkm, which provides the frictional force when unitizing. It is suggested to get the die hole for briquetting by dimensional electric arc with a given roughness of Ra = 3,2..6,3 mkm of the side walls of the matrix, which allows you to take great allowances material at the lowest cost processing time. In such a case the cycle of matrix processing decreases in 4,1-5,2 times. The objectivity of technological schema of die hole formation by the method of dimensional processing by electric arc with consideration of specialties of physical mechanism of creation and hydrodynamic phenomena in electrode period was performed. The analytical connections of technological processing characteristics of sized processing by electrical arc of steel X12MF were established, with the modes of processing and geometrical parameters.Item Концептуальні питання забезпечення механічної надійності сільськогосподарської техніки(КНТУ, 2015) Гринченко, О. С.; Grinchenko, OleksandrВикладено зміст концептуальних питань забезпечення механічної надійності сільськогосподарської техніки. Відмічено ключове значення інверсійного методу визначення характеристик еквівалентного навантаження. The presence of a common methodology ensure mechanical reliability lays the foundations for the formation and effective functioning of the integrated informational and methodological system for modeling, forecasting, and ensure mechanical reliability of machines. The developed inversion method for analysis and determination of equivalent loads can improve confidence in forecasting of indicators of reliability of mechanical items of agricultural machinery at the design stage. The inversion method implements a combination of statistical and mechanical models of reliability. Received inversion method information is equivalent to the load of analogue need to use when designing new or modernsoul object, the calculation of which it is possible to apply the same mechanical reliability models. Considered the totality of methods of rapid assessment and models for prediction of mechanical reliability forms a common methodology, the application of which in testing, modelling and design of agricultural machinery is essential to improve its quality and competitivenessItem Дослідження процесу заряджання насінини в насіннєпровід координатного гідропневматичного висівного апарата(КНТУ, 2015) Бойко, В. Б.; Boyko, VladislavРозроблено математичну модель процесу заряджання насіння до насіннєпроводу координатного гідропневматичного висівного апарата з використанням в програмного пакету STAR-CCM+. Отримано результати чисельного моделювання процесу зарядки насінини дозволило визначити залежність мінімальної початкової швидкості потоку рідини через гідро клапан Vt від ширини забірної камери В і початкової швидкості рідини V0 в ній. In the Dnepropetrovsk agrarian University is working to coordinate implementation of the agriculture using bridge machines. Coordinate agriculture will implement a personalized approach to the cultivation of vegetable crops, thus reducing mechanical and chemical effects in crop production. To improve the efficiency of agriculture bridge designed and manufactured a prototype of the coordinate hydropneumatic sowing device. In this paper, an analysis of recent publications on transportation of seed in hydraulic seeding machines. Using the software package STAR-CCM+, the mathematical model of the charging process of the seeds in the seed channel to coordinate hydropneumatic sowing device. The results of numerical simulation of the charging process of the seed made it possible to justify the minimum value of the initial flow rate of fluid passing through the hydraulic valve device, and transports the seeds from the suction chamber into the channel for the seed.Item Обґрунтування конструктивно-технологічної схеми багатокомпонентного дозатора-змішувача інгредієнтів комбікормів(КНТУ, 2015) Бойко, Д. І.; Boyko, DenisВ результаті аналізу технологій приготування комбікормів для тварин і птиці, способів дозування і змішування інгредієнтів комбікормів, а також конструкцій дозаторів і змішувачів запропонована нова конструкція дозатора-змішувача в якій операції дозування і змішування інгредієнтів об’єднані в одну технологічну операцію і виконуються одним робочим органом. Головною перевагою запропонованої конструкції є об’єднання операцій дозування і змішування, що значно спрощує конструкцію дозатора-змішувача і зменшує енергетичні витрати для його приводу. Висока якість змішування досягається за рахунок багатокомпонентного зв’язного дозування і тонкошарової взаємодії змішуваних компонентів. The purpose of this work is an analysis of existent constructions of metering devices-mixers of ingredients of the mixed fodders, exposure of their advantages and failings that development of perspective construction in which to foresee intensification of process by the association of operations of dosage and mixing due to their implementation by one working organ. The basic constructions of metering devices-mixers are considered for preparation of the mixed fodders and directions of their improvement are offered. Advantage of the offered construction of metering device-mixer is that the operations of dosage and mixing are executed one working organ, by motive forces here, that operate there are centrifugal forces on friable material. It allows considerably to reduce power charges on preparation of the mixed fodders. In theory the productivity of the offered construction of metering device-mixer is certain and graphic dependences of the productivity are built on structurally kinematics of parameters. As a result of analysis of constructions of metering devices-mixers directions of their improvement are certain and the new construction of metering device-mixer, in which the process of dosage and mixing is executed one working organ which will provide the considerable cutting of power costs on the process of preparation of the mixed fodders, is offered. The conducted theoretical researches are set intercommunication of the productivity of metering device-mixer from it`s structurally kinematics parameters.Item Самозагострювання робочих органів ґрунтообробних знарядь(КНТУ, 2015) Дворук, В. І.; Войтов, В. А.; Борак, К. В.; Dvoryk, Volodymyr; Voytov, Viktor; Borak, KonstantinДосліджено вплив фізико-механічних властивостей матеріалу робочого органу, абразивних властивостей ґрунтів і конструктивних параметрів робочого органу на виникнення ефекту самозагострення. Отримані уточненні умови самозагострювання для робочих органів дискових ґрунтообробних знарядь. Set conditions of independent intensifying working organ soil-cultivating instruments. Influence of mechanical properties of material working organ, abrasive properties soils, structural parameters of working organ is investigational on the origin effect of independent intensifying. Got clarification of condition of independent intensifying for the workings organs of disk soil-cultivating instruments: 1. Value thickness and hardness of the strengthening and base layer should be a lifetime condition to ensure R < Rɞ. 2. The thickness of the base layer should be as short as possible, while providing the necessary increase in strength solid layer. 3. The hardness of hardened layer should be determined in relation to the base layer hardness depending on the abrasive properties of soil. 4. Strengthening and exacerbate the line and must be subject to more intense wear that. 6. Sharpening angle must be at 28Û ... 30Û. To achieve the effect independent intensifying working organ soil-cultivating instruments must fulfill five conditions and the second and the third condition suggested by V.M. Tkachev for plowshares completely fair and intensifying working organ soil-cultivating instruments, the first condition is clarified, and 4 opposite condition is reversed.Item Результати експериментальних досліджень розкидача підстилки з роторно-пальцевим робочим органом(КНТУ, 2015) Парієв, А. О.; Дробишев, О. О.; Коротченко, Т. М.; Pariiev, Andrew; Drobyshev, Oleh; Korotchenko, TatyanaПроведено експериментальні дослідження розкидача підстилки з роторно-пальцевим органом. Експериментальний зразок розкидача підстилки відповідає зоотехнічним вимогам, забезпечує локальну та дозовану подачу (0,5кг/гол.) солом’яної підстилки в бокси. feeding CLI-10, which corresponds to the zootechnical and technological requirements of making straw bedding in boxes. Conduct of experimental studies spreader. The experimental sample spreader corresponds zootechnical requirements, provides local and dosing straw / As a result of experimental research results: - weight solomorozkydach performance - 0.5 -3.7 t / h; - straw accordance with the requirements zootechnical provide local supply and dosage (0.5 kg / head.) the bulk of scattered straw in the 1/3 lair and meets the technical requirements - working body ensures its distributor stable operation of damp straw (over 16%); - straw experimental model requires testing of existing dairy farms cattle.Item Результати експериментальних досліджень питомих енерговитрат транспортування зерна гвинтовим конвеєром(КНТУ, 2015) Грудовий, Р. С.; Hrudovyi, RomanПредставлена наукова робота висвітлює результати експериментальних досліджень зміни величини питомих енерговитрат, під час транспортування гвинтовим конвеєром з рівнозбільшеним кроком витків в напряму руху вантажу зерна пшениці та ячменю, від зміни трьох основних факторів: від приросту кроку шнека на одному витку ΔТ, кута нахилу конвеєра γ та частоти обертання шнека n, тобто w=f(ΔТ,γ,n). Отримані рівняння регресії для визначення величини питомих енерговитрат гвинтового конвеєра у таких межах зміни вхідних факторів: 0,003 ΔТ 0,007 (м); 15 γ 45 (град); 100 n 400 (об/хв). За допомогою прикладної програми побудовано графічне відтворення проміжних загальних регресійних моделей у вигляді квадратичних поверхонь відгуку та їх двомірних перерізів величини питомих енерговитрат. Aim of the research of the experimental sample was to determine effects of change of volute step length size to the movement of bulky materials and to the energy requirements and comparison with transportation of bulky materials by the screw working tool of the same parameters, but with permanent step. To determinate influence of constructive and cinematic parameters (independent factors i x ) of the spiral conveyor to its energy requirements during transportation of wheat and barley ( parameter of optimization w), there was conduct the experiment of determination of energy requirements during transportation of grain from change of three main parameters: increase of volute step on one volute ǻɌ, angle of slope of the conveyor Ȗ and frequency of rotation of the screw n, in general w=f(ǻɌ,Ȗ,n). Processing of received experimental data was done due to usage of common methods of regressive analysis. Analysis of received experimental data shows, that increasing of angle of slope of the spiral conveyor causes increasing of energy requirements, the largest requirements is 0,05 kW·hour./t·m. Increasing of volume step from 0,003m to 0,007m causes decreasing of energy requirements from 5 to 10 %. Increasing of angle of slope of the spiral conveyor from 15 to 45 degrees causes increasing of energy requirements from 20 to 50 %. That’s why increasing of the volume step is the proven method of energy requirements.Item Особливості реалізації промисловими роботами механоскладальних технологій в гнучких виробничих комірках(КНТУ, 2015) Кирилович, В. А.; Kyrylovych, ValeriiНа підставі змістовної сутності та технологічної спільності застосування промислових роботів (ПР) при механоообробці та складанні обгрунтовується термін “роботизована механоскладальна технологія (РМСТ)”, дається її визначення. Розроблені формалізми структури РМСТ покладені в основу аналізу відношень між складовими РМСТ. Вказано на доцільність розглядати термін “траєкторія” щодо переміщення полюса схвата промислового робота, а термін “траєкторний простір” – щодо переміщення технологічного роботизованого комплекту. Aim of the paper is to highlight the substantive features of robotized mechanical assembly technologies that are invariant relatively manufacturing types and industry kinds, for further automated implementation. The main feature of robotized mechanical assembly technology is technologically ordered set of industry robot gripper movements. It is implemented on certain paths to certain parameters, such as the values of movements, velocities and accelerations of the each links of inductrial robot’s manipulation system. The said is the basis for the formation of trajectories that may be implemented by known reference points, by completely or partially smoothed trajectories. Mentioned above is formalized and it as the staging plan which was the basis for the further development and implementation of automated methods of choising of the optimal robotized mechanical assembly technology.