Конструювання, виробництво та експлуатація сільськогосподарських машин. Випуск 43. Ч. 1 - 2013
Permanent URI for this collectionhttps://dspace.kntu.kr.ua/handle/123456789/1717
Browse
Search Results
Item Измерительные приспособления для определения момента инерции двигателя сельскохозяйственных тракторов(КНТУ, 2013) Kiernicki, Zbigniew; Semczuk, Paweł; Nowak, Andrzej; Керницькі, З.; Семчук, П.; Новак, А.В статье представлены устройства, предназначенные для проверки момента инерции двигателя при тройном ускорении с помощью дополнительного веса. Методология измерения предполагает, что для данной скорости и теплового состояния двигателя момент, который развивается, сравнительно эффективный. У статті представлені пристрої, які призначені для перевірки моменту інерції двигуна при потрійному прискоренні за допомогою додаткової ваги. Методологія вимірювання передбачає, що для даної швидкості і теплового стану двигуна момент, який розвивається, порівняно ефективний. Отримана маса моменту інерції розглядається як достатня для ефективного обертання колінчастого валу. Полученная масса момента инерции рассматривается как достаточная для эффективного вращения коленчатого вала. The purpose study was to determination of the mass inertia moment of the engine of agricultural tractors. To this end, the proposed equipment in which the principle of triple inertial mass and acceleration using additional load tractor PTO. Testing adaptation was carried at the company Claas tractors and Ursus. The measurement methodology assumes that effective torque is comparable at given speed and thermal state of the motor. Resulting mass moment of inertia is treated as an average one for the full rotation of the crankshaft. In this connection there possibility of investigating the mass inertia moment the engine in any configuration that will greatly expand the use of the proposed methods for the assessment of the technical condition engine and the precision of its regulation.Item Система керування режимом розігріву процесу екструзії полімерів(КНТУ, 2013) Ярощук, Л. Д.; Жученко, О. А.; Jaroshuk, Ludmila; Zhuchenko, AlekseyЗапропонована система керування режимом розігріву процесу екструзії полімерів. Система використовує принципи керування з внутрішньою моделлю. Як математична модель процесу нагрівання використовується інтегральна ланка другого порядку з запізнюванням. Для ідентифікації моделі застосований метод інструментальних змінних. Розроблений метод налаштування системи керування, який забезпечує її робастну стійкість по відношенню до неточності параметрів математичної моделі. Проведене дослідження представленої системи керування шляхом порівняння якості її роботи з іншими відомими аналогічними системами. Результати дослідження свідчать про високу ефективність запропонованої системи керування. The control scheme based on internal model control (IMC) structure has been proposed for heating-up, which is capable of no overheating (i.e., temperature overshoot) for heating-up. Analytical controller-design formulas and quantitative tuning guidelines have been given for implementation of the desirable heating-up response together with robust tuning constraints to accommodate for process uncertainties. For temperature-control design an identification method based on the step response has been used for obtaining the heating-up model. The proposed control system was compared to the well-known Ziegler-Nichols PID tuning method based on the integrating first-order-plus-dead-time model and Skogestad IMC-based PID tuning method, using the proposed integrating second-order-plus-dead-time model. This comparison has well demonstrated the effectiveness of the developed identification method and control scheme for the application to the barrel-temperature control of polymers extrusion process.Item Визначення основних параметрів хвильових процесів при роботі електромеханічного актуатору подачі палива(КНТУ, 2013) Швець, І. А.; Shvets, IgorВ статті описано причини появи та можливі наслідки від дії хвильових процесів отриманих внаслідок короткочасного дроселювання газу під час роботи електромеханічного актуатору подачі газового палива. Представлено математичні залежності що описують параметри газового потоку та хвильових процесів для даного пристрою. Оцінено вплив зазначених процесів на роботу пристрою взагалі. The aim of this work is the definition of the main parameters of the wave processes at work electromechanical actuator supply gas fuel.In the course of this work revealed that the occurrence of wave processes directly related to the interval of time spent on the opening and closing of the metering orifice. Often sold to influence the dosage and the emergence of gas shock will have a shock wave, reflected wave and the expansion wave. Obtain the basic mathematical relations for the basic parameter has wave processes. The obtained dependences reflect the influence of the main factors on the occurrence of wave processes.Item Синтез конструктивно-технологічних схем – основа для розробки багатофункціональних комбайнів(КНТУ, 2013) Шведик, М. С.; Shvedik, NikolayУ статті наведено результати аналізу існуючих конструктивно-технологічних схем як зернозбиральних комбайнів, так і одно-, двоопераційних машин з різних галузей і на основі виявлених найбільш характерних їх функціональних особливостей, що в тій чи іншій мірі можуть бути синтезовані в одну структурно-технологічну схему, розроблено багатофункціональний збиральний комбайн. A research purpose is an analysis of existent structurally-technological charts of both combine harvesters and other devices and their synthesis in one structurally-technological chart multifunction collective to the combine. The conducted structurally-biological analysis of grain attr layer of ear grain-crops showed that 70% grains is in 30-ty centimetre ear layer, and other grain - in undersized stems. It underlay development of new principle of collection of ear grain-crops, namely is diminishing to the volume of biological mass, which is given both on threshing and on cleaning. As a result of synthesis of design-technological charts of combine harvesters and other devices a chart is worked out much-functional to the combine, which provides the twotier cut of ear and pedicellate mass, her separate threshing, the knocked out catches grain by a reel and produces other works. Conclusion: the new combine provides the twotier cut of ear and pedicellate mass, her separate threshing, the knocked out catches grain by a reel and produces other works.Item Застосування металполімерних композитів в конструкціях сферичних шарнірів просторової системи приводів(КНТУ, 2013) Струтинський, С. В.; Strutins'kij, SergeyЗапропоновано конструкцію сферичного шарніра просторової системи приводів, у якій сферичне сідло виконано з металополімерного композиту. Розроблена технологія і виготовлено дослідний зразок шарніра, поверхня сідла якого досліджена з використанням електронних мікрофотографій. Встановлена структура композиту та кількісні характеристики наявних в ньому металевих включень. Визначено розміри залізних сфер, які складають металеву основу композиту. Досліджено показники якості мікропрофіля для одержаної сферичної поверхні.The aim of the paper is the development of design and manufacturing technology manufacturing techniques spherical joints using metalpolimer composites and experimental testing of the installation parameters obtained spherical surfaces. The construction of the spherical joint space drive systems in which spherical seat is made of metalcomposite. The technology and joint production model, the surface of the saddle which investigated using electron micrographs. Installed composite structure and quantitative characteristics of existing metallic inclusions in it. As a result of work performed confirmed the possibility of spherical joints with metalpolimer composite. Found that produced spherical surface with high quality.Item Дослідження впливу конструктивних параметрів героторної передачі на зносостійкість робочих профілів коліс(КНТУ, 2013) Скібінський, О. І.; Гнатюк, А. А.; Зеленько, В. М.; Skibinskiy, Aleksandr; Gnatuk, Andrey; Zelenko, VyacheslavВ статті приведено дослідження впливу конструктивних параметрів на інтенсивність ковзання, як одної з основних причин зносу робочих профілів деталей героторних передач, а також виведення точних залежностей для визначення таких параметрів, вибір яких дозволяє зменшити вплив тертя ковзання і відповідно підвищити зносостійкість профілів. The purpose of this paper is to determine the optimal structural parameters of gerotor transmission, allowing to reduce the harmful effects of friction, which is a major cause of wear of wheel profiles. In this article is described a study of the relationship between the design parameters of the gerotor transmission and intensity of wear of the working profiles of wheels. Analysis of the work of gerotor transmission allowed us to establish portions of profiles that are most subject to wear. Because the parameter of wear is a specific sliding , the wear rate will depend on the length of the plot sliding friction. The study presents precise formulas to get the optimal value of the radius of the stator tooth, in which portions of friction profiles are equal. The obtained value of the radius of the stator tooth can not completely exclude the specific friction factor, but it allows you to evenly distribute it to the moving portions of the profile, thereby minimizing the harmful effects of friction and improve durability.Item Результати польових випробувань дискового плуга, адаптованого для роботи в умовах півдня України(КНТУ, 2013) Семенюта, А. М.; Волик, Б. А.; Дубовик, В. О.; Semenyuta, Anatoliy; Volyk, Boris; Dubovik, ViktorВ статті обґрунтовано доцільність використання дискового плуга в складних грунтових умовах, де використання полицевого плуга є проблематичним. На основі аналітичних досліджень запропонована конструкція і наведені раціональні параметри плуга для умов півдня України. Особливість запропонованого конструктивного рішення полягає в тому, що диски плуга встановлені з можливістю зміни кутів постановки до вертикалі і напрямку руху. Це дозволяє отримувати наперед обумовлені показники якості розпушення грунту в різних грунтових умовах. Наведені результати експериментальних досліджень підтверджують основні положення виконаних аналітичних досліджень. Work Objective - reducing energy output of the process of soil treatment and improving quality performance of the disk plough through definition of rational parameters of its design. Summary of the work Based on the conducted analytical studies the disk setting angles with respect to the vertical line and direction of the movement of the implement providing the best indicators of quality of soil pulverization under the soil conditions of the southern Ukraine were substantiated. A rational design scheme of the plough which provides the minimum value of the transverse component of traction resistance has been given. The paper presents the results of assessment of the quality of soil pulverization by screening of the collected samples on the sizing screen in real operating conditions. Conclusions. As a result of the field studies the following rational structural design parameters have been defined: – disk diameter, mm – 660; – disk surface curvature, mm – 620; – disk setting angle with respect to the direction of movement, degrees – 38-42; – disk setting angle with respect to the vertical, degrees – 22-26. A significant advantage of the plough is that its five-housing option can be aggregated with the tractor class 14 kN, while the regular share plough with class 30 kN.Item Розробка САК змінними нормами висіву на базі сівалки СЗ-3,6(КНТУ, 2013) Пархоменко, Ю. М.; Пархоменко, М. Д.; Parhomenko, Yuriy; Parhomenko, MikhailДосліджуються шляхи створення програмно-адаптивної автоматизованої системи керування змінними нормами висіву зерновими сівалками при сівбі за технологією точного землеробства. Визначається параметр та закон регулювання. The purpose of this paper is to investigate ways to create automatic control system (ACS) variable seeding rates for precision farming technology based drills SZ-3, 6 using the upgraded device registration and authentication of computer grain flow. The ways of creating software and adaptive automated control system for variable seed rate at sowing grain drills for precision farming technology are investigated. The parameter and the control law are determined. The hardware of the automatic control system developed includes trip computer with display, GSP receiver, routing-problem variable seed rates on an electronic medium (sowing map) Sensor speed drills, drills sensor included in the work; node registration and node synchronization preprocessing and data that make up the computer system identification ( CCI ) and play the role of feedback, line of electric control unit and lever feed shaft drill seeding machines. Function block incoming data and the formation of the current values of the density distribution of grain rely on the onboard computer. Overall, the described set is a closed dynamic ACS. In addition to improving the quality of sowing, the introduction of automatic control eliminates the need for preplant setting drills seed set rate, as this is done automatically on the first meters sowing by overshoot the programmed through each turn of the supporting-wheel drive drills.Item Применение эжекторов в пневмоструйной технике агропромышленного комплекса(КНТУ, 2013) Панков, А. А.; Щеглов, А. В.; Панков, А. О.; Щеглов, А. В.; Pankov, Andrej; Shcheglov, AndrejВ статье рассмотрены возможности применения и повышения эффективности эжекторов для питания элементов и устройств пневмоструйной техники в агропромышленном комплексе, а также представлены результаты исследования рабочего процесса плоского эжектора в однозерновом высевающем аппарате с шаговым приводом. У статті розглянуто можливості застосування і підвищення ефективності ежекторів для живлення елементів та пристроїв пневмоструминної техніки в агропромисловому комплексі, а також представлено результати дослідження робочого процесу плоского ежектора в однозерновому висіваючому апараті з кроковим приводом. The aim of the application elements ejectors is the case when using gas jet compressor (or vacuum pump) is difficult or inefficient to process or operational reasons. To create a vacuum in the agricultural machinery pnevmostruynyh devices rational use of compact elements, ejectors flat type. Analyzed by odnozernovom sowing unit ejector element has an operating pressure of 7 kPa insufficient capacity for the transport of sunflower seeds. To ensure a bottom feeder metering drum sowing material, you need to change the working nozzle orifice to increase the flow of air powered ejector 1.4 times. Thus, consider using elements of ejectors to supply components and devices pnevmostruynoy technology, as well as the results of research workflow flat ejector Planting unit with stepper drive.Item Виробничі технології як альтернатива обкатування деталей ДВЗ(КНТУ, 2013) Ошовський, В. Я.; Oshovsky, ViktorРозглядаються технології обробки в умовах виробництва як альтернатива обкатування для підвищення ресурсу деталей двигуна внутрішнього згоряння (ДВЗ). Проаналізовано недоліки обкатування та запропоновано метод збільшення ресурсу рухомих спряжень. Доведена можливість збільшення ресурсу рухомих спряжень ДВЗ притиранням і шаржуванням алмазними пастами.Technologies of treatment in the conditions of production are examined as an alternative to rolling for the increase of details resource of internal-combustion engine (ICE). The lacks of rolling-off are analysed and the method of increasing the resource of mobile interfaces is offered. Possibility of the increasing of resource of mobile interfaces by the ICE grinding and caricaturing by diamond pastes is proved.