Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
5 results
Search Results
Item type:Item, Моделювання руху двомасового вібраційного живильника на базі гідроімпульсного привода(ЦНТУ, 2018) Іскович - Лотоцький, Р. Д.; Коц, І. В.; Іванчук, Я. В.; Івашко, Є. І.; Искович - Лотоцкий, Р. Д.; Коц, И. В.; Иванчук, Я. В.; Ивашко, Е. И.; Iskovych-Lototskyi, R.; Kots, I.; Ivanchuk, Y.; Ivashko, Y.Розроблена нова оригінальна конструкція двомасового вібраційного живильника на базі гідроімпульсного привода, яка врівноважує надлишкові динамічні навантаження. Проведено теоретичне дослідження двомасового вібраційного живильника з гідроімпульсним приводом на базі розробленої математичної моделі. У процесі дослідження була розроблена розрахункова схема пристрою та отримані основі математичні залежності які характеризують режими його роботи та взаємозв’язок робочих параметрів, а також дають змогу оцінити актуальність та перспективність оригінальної розробки. Разработана новая оригинальная конструкция двухмассового вибрационного питателя на базе гидроимпульсного привода, которая уравновешивает избыточные динамические нагрузки. Проведено теоретическое исследование двухмассового вибрационного питателя с гидроимпульсным приводом на базе разработанной математической модели. В процессе исследования была разработана расчетная схема устройства и получены основные математические зависимости, что характеризуют режимы его работы и взаимосвязь рабочих параметров, а также дают возможность оценить актуальность и перспективность оригинальной разработки. The main disadvantage of powerful vibrating feeders with different types of drives, performed on a single-mass scheme, are high dynamic loads on the elements of load-bearing structures. The aim of the article is to develop a mathematical model of the motion of a two-mass vibrating feeder based on a hydroimpulse drive, to confirm the feasibility of developing and its performance in the future. Vibrating feeders with a hydropulse drive are tuned to near resonance mode, as a result of which the dynamic load on the foundation can reach very high values. The solution to this problem is to establish an additional reactive mass, which will absorb the excessive dynamic loads. A new original design of a two-mass vibrating feeder based on a hydropulse drive is developed, which balances the excess dynamic loads. A mathematical model of the motion of a two-mass vibrating feeder is developed, which is represented by a system of Lagrange differential equations. The solution of the mathematical model of motion of a vibrating feeder was carried out by the method of introducing a complex variable. A theoretical investigation of a two-mass vibrating feeder with a hydroimpulse drive based on the developed mathematical model is carried out. In the process of research, the design scheme of the device was developed and the mathematical dependences obtained on the basis of a system of differential equations were derived. A mathematical model of the motion of a vibrating feeder has been developed which allows to optimize the parameters of debugging of the hydroimpulse drive and to outline ways to solve the problem of extremely high dynamic loads on the foundation while developing new original designs of two-mass vibrating feeders. Solving the system of differential equations that characterize the modes of its operation and the interrelationship of operating parameters make it possible to assess the relevance and prospects of the original development.Item type:Item, 3D модель для исследования динамики центробежной соковыжималки с шаровым автобалансиром(КНТУ, 2013) Гончаров, В. В.; Филимонихин, Г. Б.; Гончаров, В. В.; Філімоніхін, Г. Б.; Goncharov, Valeriy; Filimonikhin, GennadyСоздана 3D модель центробежной соковыжималки с цилиндрическим ситом и шаровым автобалансиром для ее уравновешивания на ходу в САПР SolidWorks. С использованием модуля Cosmos Motion проведена обработка, наладка и тестирование модели. Модель предназначена для исследования динамики машины, проведения виртуальных многофакторных экспериментов. Створена 3D модель відцентрової соковижималки з циліндричним ситом і кульовим автобалансиром для її зрівноваження на ходу в САПР SolidWorks. З використанням модуля Cosmos Motion проведено обробку, налагодження і тестування моделі. Модель призначена для дослідження динаміки машини, проведення віртуальних багатофакторних експериментів. In the process of work of electric centrifugal juicers (juicers) with the cylindrical sieve the pulp is distributed non-uniformly on a sieve which causing a significant imbalance and vibration of machine case. To balance these juicers on the go in the operation the authors propose their modernization which consists in replacing the standard platform for mounting the sieve by platform combined with ball auto-balancer. In order to study the process of balancing by auto-balancer of juicer’s cylindrical sieve created its 3D model with using the CAD system SolidWorks and its module Cosmos Motion. The simulation was performed in a technique that can be adopted as the standard for modeling process-balancing in rotor systems. It includes the steps of: 1) creation of models of details of a juicer in SolidWorks; 2) union of details in assembly; 3) kinematic and power processing of assembly by the Cosmos Motion module; 4) choice of criteria of quality of operation of the auto-balancer and juicer (the value of the module of residual acceleration of the case, time of onset of auto-balancing etc.); 5) adjustment of the model (the values of its parameters are selected in maximum accordance with the real machine); 6) the choice of model parameters; 7) test of the model of elementary tasks, the results of which are known or can be easily interpreted. The model of a juicer created by the offered technique is efficient and provides high speed of calculations. Its key parameters correspond to a natural juicer with the ball-type auto-balancer. By means of the created model it is possible to make fully - factorial and multiple-factorial experiments, in particular – with 2-levels, 3-levels, for search of optimum values of parameters of a juicer with the auto-balancer.Item type:Item, Вібромоніторинг холодновисаджувальних автоматів(КНТУ, 2013) Кришкін, Б. Б.; Теплюк, М. П.; Kryshkin, B.; Tepljuk, M.У статті описано методику вібраційного моніторингу високошвидкісних холодновисаджувальних автоматів із застосуванням програмного комплексу 20-sim. Запропоновано оптимальну послідовність процедур вібромоніторингу з метою підвищення точності на довговічності роботи обладнання. An aim of work is research and analysis of procedures of the oscillation monitoring of high-speed stamping equipment, in particular, upsetting automats. In the article the results of estimation of level and intensity of vibrations are presented in the elements of drive of automat of А1214, got with the use of programmatic complex 20-sim. It is shown that the design of shake processes with the use of such complex allows not only considerably to decrease labour intensiveness of monitoring procedures but also to provide universality and flexibility of subsequent calculations of vibrospeed and vibroacceleration. Materials, expounded in the article, can be useful to the researchers and exploitations of high-speed stamping equipment.Item type:Item, Спектральні характеристики вібраційних параметрів токарного багатошпиндельного автомата(КНТУ, 2008) Черновол, М. І.; Кропівна, А. В.; Струтинський, В. Б.В статті приведені результати експериментального визначення вібраційних параметрів токарних багатошпиндельних автоматів. Визначені резонансні частоти вібраційних збурень в динамичній системі токарного багатошпиндельного автомата 1Б2656К. In article results of experimental definition of vibration parametres of multi-spindle rod automats. Resonant frequencies of vibrating indignations are certain in dynamic system of multi-spindle rod automats of 1Б2656К.Item type:Item, Дослідження мікропрофіля поверхні одержаного вібраційною обробкою фрезами малого діаметра(КНТУ, 2015) Струтинський, В. Б.; Перфілов, І. В.; Strutynsky, Vasil; Perfilov, IvanВикладено результати досліджень мікропрофіля поверхні одержаного фрезерувальною обробкою фрезами малого діаметра на спеціально розробленому обладнанні. Показано, що мікропрофіль включає ділянки з ізольованими екстремумами та ділянки квазіперіодичності із чітко визначеним напрямком мікрорисок. Запропоновано опис мікропрофіля аналітичними залежностями. Для ділянки з ізольованими екстремумами опис мікропрофіля проводиться функціями на основі кривих Гауса. Для ділянок квазіперіодичності рекомендований спектральний аналіз мікропрофіля шляхом подання його у вигляді відрізка ряду Фур’є. Виконано аналіз особливостей мікропрофіля по різним ділянкам. The results of surface microprofile research obtained with the milling cutters of small diameter on a specially designed equipment are presented. It is shown that the microprofile includes the areas with isolated extremes and the areas of quasiperiodicity with a clear focus of microstrips. A microprofile description with analytical dependencies are suggested. For the areas with isolated extremes the description of microprofile functions is carried out based on the Gaussian curves. For areas with quasiperiodicity the spectral analysis of microprofile by submitting it as a segment of a Fourier series is recommended. The analysis of microprofile in different areas is made. The research purpose is to develop methods for assessing the quality parameters of obtained microprofile which was processed with small diameter mills with imposing high vibration on the workpiece. The special equipment for forming the microprofile was developed. Methods for estimating the microprofile parameters in areas with isolated extremes and in areas with quasi-periodic statements and valves were suggested. The analytical description of microprofile with the set of Gaussian curves and segments of Fourier rows based on microprofile spectrum analysis. The microprofile features analysis was made. The conclusion about the microprofile quality parameters obtained with vibration processing with small diameter mills and the methods of this type of microprofile analysis.