Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
12 results
Search Results
Item Теоретичні дослідження заповненості клапанного мішка сипким матеріалом(КНТУ, 2005) Оришака, О. В.; Гончаров, В. В.; Кравцов, А. О.Обгрунтовані залежності для визначення незаповнених зон клапанного мішка і вплив на їх величину вихідної швидкості потоку сипкого матеріалу, кута нахилу завантажувального патрубка і фізико-механічних властивостей сипкого матеріалу. The proved dependences for definition of the blank zones klapans a bag and influence on their size of initial speed of a stream of a loose material, a corner of an inclination of a loading branch pipe and physicomechanical properties of a loose material.Item Теоретичне дослідження руху сипкого матеріалу в постачальному пристрої установок безперервної дії(ЦНТУ, 2019) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Орышака, О. В.; Гуцул, В. И.; Артюхов, А. Н.; Oryshaka, O.; Gutsul, V.; Artiuhov, A.Отримані залежності швидкості руху сипкого матеріалу в постачальному пристрої установок безперервної дії від геометричних параметрів постачального пристрою, а також визначено діапазон зміни швидкості руху сипкого матеріалу в постачальному пристрої. Полученны зависимости скорости истечения сыпучего материала в подающем устройстве установок непрерывного действия от геометрических параметров питающего устройства, а также определён диапазон изменения скорости истечения сыпучего материала в подающем устройстве. Continuous-action plants have several advantages over cycle-feed units (low energy costs, high productivity, lower material consumption, etc.), so improving continuous-action installations is an urgent task. The bulk material feeder, as an integral part of the continuous-action plants, requires appropriate research to substantiate and optimize the design parameters of the installation. The purpose of this work is to investigate the influence of the geometrical parameters of the stabilizing slope of the delivery devices of the continuous-action installations for loading free-flowing materials on the speed of movement of the bulk material and, thus, the technological process of the installation for loading bulk materials. The dependences of the velocity of the free-flowing material in the delivery device of the continuous devices on the geometric parameters of the supply device are determined, as well as the range of velocity variation of the bulk material movement in the feed device is determined. Research findings. The velocity of loose material increases with increasing radius r (fig. 3) and angle (fig. 2). The range of variation in speed (variability, boundary limits) of the velocity of free-flowing material in the supplying device is determined. At , the velocity of the free-flowing material varies between 2,11 ... 2,3 m / s. The obtained results allow to determine the values of the main geometric parameters of the supply device of the continuous devices to provide the required output indicators The results obtained allow us to determine the values of the basic geometric parameters of the stabilizing slope of the delivery devices of the continuous operation installations to provide the required output indicators.Item Теоретичне дослідження регулятора витоку сипкого матеріалу(ЦНТУ, 2017) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryshaka, O.; Gutsul, V.; Artiuhov, A.Отримані залежності впливу кута нахилу поверхні конусного ската регулятора витоку сипкого матеріалу та радіуса округлення торцевої частини полого циліндра регулятора витоку сипкого матеріалу на максимальне значення переміщення конусного ската, при якому площа витоку сипкого матеріалу залишається меншою за площу вхідного отвору матеріалопровода; залежності впливу значення переміщення конуса на час повного вивантажування бункера; залежності, які дозволяють визначати швидкість витоку матеріалу та об'єм вивантаженого матеріалу при різних значеннях основних параметрів регулятора. The dependences of the influence of the angle of slope of the cone-slope surface of the regulator of the outflow of loose material and the radius of rounding of the end part of the hollow cylinder of the flow-out material flow controller on the maximum value of the cone-shaped slope movement, at which the flow area of the loose material remains less than the area of the inlet of the material duct; Dependence of influence of value of cone displacement on the time of complete unloading of the hopper; Dependencies that allow to determine the flow rate of.Item Теоретичне дослідження конусного стабілізатора потоку сипкого матеріалу установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2016) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryshaka, О.; Gutsul, V.; Artiuhov, А.Отримані залежності швидкості руху сипкого матеріалу по конусному стабілізатору залежно від величини кута конуса, відстані від конусного стабілізатора до заслінки клапана і коефіцієнта тертя сипкого матеріалу, зазору між торцем матеріалопровода і конусним стабілізатором, товщини шару сипкого матеріалу, що сходить з поверхні конуса. The resulting dependence of the speed of the free-flowing material in the feed device from the height of the free flight, the coefficient of friction, angle of inclination of the side walls of the receiving receiving hopper, as for the case of fixed position receiving hopper, and for the case of circular motion of the funnel for different values of the angular velocity. When you increase the angle of the surface of the cone to the horizontal and V0 the speed of descent of granular material from the cone increases, and the thickness of the layer of bulk material flow that is coming off the cone decreases. A significant impact on the speed of descent of granular material from the cone and the thickness of the layer of bulk material flow that is coming off the cone f has. For large values of the coefficient of friction of the granular material on the surface of the cone, the surface of the cone to cover the materials with small values of the coefficient of friction.Item Дослідження вихідної швидкості сипкого матеріалу з постачального пристрою гравітаційно-роторного типу(КНТУ, 2008) Артюхов, А. М.; Оришака, О. В.; Оришака, В. О.У статті розглядаються питання побудови математичної моделі технологічного процесу завантаження дрібнозернистих сипких матеріалів двороторним постачальним пристроєм у клапанні мішки, представлено результати впливу основних параметрів постачального пристрою на вихідну швидкість сипкого матеріалу для здійснення технологічного процесу. In clause questions of construction of mathematical model of technological process of loading finegrained loose materials be a bilateral feeder in valvular sacks are considered, results of influence of key parameters of a feeder for target speed of a loose material for realization of technological are presented.Item Обгрунтування параметрів установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2011) Оришака, О. В.; Оришака, В. О.; Артюхов, А. М.; Кравцов, А. О.; Oryshaka, О.; Oryshaka, W.; Artiukhov, А.; Kravtsov, А.Обґрунтовані параметри нових принципових рішень, які передбаченні в конструкції установки безперервної дії для завантаження сипких матеріалів нового покоління з метою підвищення технологічної надійності процесу завантаження, а саме телескопічного клапана, який дає можливість стабілізувати напруження в сипкому середовищі в зоні вивантажувального отвору бункера, завантажувальних пристроїв,що мають канали з випуклими криволінійними поверхнями і вертикальними вихідними патрубками, які забезпечують повне заповнення об'єму клапанного мішка сипучим матеріалом і зменшують втрати енергії при переміщенні матеріалу. In article are grounded the parameters of new of principles decisions which are foreseen in the construction of setting of unceasing action for the load of friable materials of new generation with the purpose of increase of technological reliability of process of load are grounded, namely telescopic valve, which enables to stabilize tension in a friable environment in the area of the unloading opening of bunker of loads devices with ducting, which I have protuberant curvilinear surfaces and vertical outputs union couplings which provide the complete filling of volume of alveolar sack by friable material and diminishes the losses of energy at moving of materials.Item Обгрунтування постачального пристрою установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2014) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryhsaka, O.; Gutsul, V.; Artiukhov, А.Визначений вплив параметрів постачального пристрою на швидкість руху сипкого матеріалу в каналах патрубків в стаціонарному положенні і при обертанні пристрою, зміна лінійної питомої маси сипкого матеріалу в патрубках, а також центр мас сипкого матеріалу. Установлено, що швидкість руху сипкого матеріалу в каналах патрубків при обертанні пристрою збільшується відносно його стаціонарного положення, що виключає порушення технологічного процесу із-за забивання каналів патрубків. Modern machines for loading friable materials into valve bags require a considerable amount of energy, allow the loss of fasoo material, as well as the violation of technological process at boot friable materials, so the improvement of modern mechanization is an actual scientific problem. The effect of the parameters of the feeding device the speed of movement of the friable material in the channels of the nozzle in a stationary position during rotation of the device, the change of a specific linear mass of granular material in the channel setup. It is established that the speed of the friable material in the channels of the nozzles during rotation of the device increases relative to its stationary position, which eliminates the violation of technological process of plugging nozzles. Resume: 1. The speed of movement of the friable material in patrols postchallenge of the device increases when the rotation of the rotor relative to the stationary position of the rotor. This makes it possible to avoid the accumulation of loose material that could lead to blockage of the channel. 2. With increasing angular velocity of rotation of the rotor the flow of material moves from the lower to the upper wall of the socket. 3. The weight of friable material in patrols, when the rotor is reduced.Item Теоретичне дослідження подільчо-формуючих постачальних пристроїв машин для завантаження сипких матеріалів(КНТУ, 2010) Оришака, О. В.; Гончаров, В. В.; Артюхов, А. М.; Оришака, В. О.; Orishaka, O.; Goncharov, V.; Artyukhov, A.; Orishaka, V.Теоретично обґрунтовані параметри подільчо-формуючих постачальних пристроїв машин для завантаження сипких матеріалів в клапанні мішки, а саме постачального пристрою з лійками, на вихідних частинах яких встановлені вивантажувальні патрубки з можливістю здійснювати зворотно- обертальний рух і постачального пристрою з формуючими гравітаційними поверхнями, які жорстко встановлені на корпусі, що змонтований на матеріалопроводі з можливістю здійснювати зворотно- обертальний рух. Встановлені оптимальні співвідношення вхідних і вихідних параметрів лійки та кута нахилу гравітаційної поверхні. Parameters of the division-forming nutritious device of machines for loading loose materials in valvular sacks are theoretically proved, namely the nutritious device with funnel on which target parts unloading branch pipes with an opportunity to make back and forth motion and the nutritious device with forming gravitational surfaces which are rigidly established on the case which is mounted on materials handling with an opportunity to make return-rotary movement are established. Optimum parities of entrance parameters funnel and a corner of an inclination of a gravitational surface are established.Item Дослідження фізико-механічних властивостей дрібнозернистих сипких матеріалів(КНТУ, 2011) Артюхов, А. М.; Оришака, О. В.; Оришака, В. О.; Малашенко, Ю. А.; Artyukhov, A.; Orishaka, O.; Orishaka, V. O.Теоретично обґрунтовані та експериментально досліджені фізико-механічні властивості дрібнозернистих сипких матеріалів сільськогосподарського призначення, а саме таких, які використовуються в кормовиробництві. Отримані фізико-механічні властивості досліджених матеріалів дають змогу обґрунтовувати основні параметри і режими роботи робочих органів машин, підвищити їх продуктивність при завантаженні дрібнозернистих сипких матеріалів. Physical and mechanical properties of fine-grained friable materials for agricultural purpose, namely those used in forage production, were theoretically grounded and experimentally investigated. The obtained physical and mechanical properties of the probed materials enable to ground basic parameters and modes of operation of working organs of machines, to promote their productivity when loading fine-grained materials.Item Теоретичне дослідження установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2012) Оришака, О. В.; Гончаров, В. В.; Оришака, В. О.; Кравцов, А. О.; Oryshaka, О.; Goncharov, V.; Oryshaka, V.; Kravcov, А.Проведений аналіз продуктивності установки безперервної дії порівняно з продуктивністю машин з циклічною подачею сипких матеріалів в клапанні мішки. Продуктивність установок безперервної дії для завантаження сипких матеріалів в 1,5 рази вище продуктивності машин з циклічною подачею. Визначено оптимальне число секцій в залежності від подачі матеріалу. Установлені залежності для визначення швидкості руху сипких матеріалів по гравітаційним поверхням, які розташовуються в першій і другій четвертях. The analysis performance settings continuously compared with the productivity of machines with cyclic feed bulk materials in valve bags. Production facilities for continuous loading of bulk materials is 1.5 times higher performance machines with cyclic feeding. The optimum number of sections depending on the feed material.