Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
5 results
Search Results
Item Удосконалення технології розбирання металоконструкцій механізованого шахтного кріплення(ЦНТУ, 2023) Боков, В. М.; Сіса, О. Ф.; Мірзак, В. Я.; Телюта, Р. В.; Пукалов, В. В.; Bokov, V.; Sisa, О.; Mirzak, V.; Teliuta, R.; Pukalov, V.Запропоновано технологію для розбирання металоконструкцій шахтного кріплення, що дозволяє замінити фізично важку та небезпечну працю оператора на більш легкий, механізований процес з використанням потужного гідравлічного біпреса. During operation, the hinge connections of mine supports practically stop rotating. This is due to the fact that, as a result of the aggressive mine water and strong dustiness, the diametrical clearance of 1-2 mm between the axis and the bushing is tightly filled with oxides and coal dust, especially in the connections of the base. This circumstance leads to the fact that the axes (pins) in the hinges lose their mobility and require significant effort for their dismantling. To repair the mechanized mine support, it is necessary to dismantle the hinge connections, which are formed by axes and holes in levers (traverses), base ears, and overlaps. Currently, the dismantling of hinge connections of mine supports is carried out using manual impact tools. This operation is extremely labor-intensive, physically heavy, and belongs to hazardous work. The goal of the study is to improve the working conditions of the operator during the dismantling process of axes in hinge connections of mine supports by using a mechanized specialized hydraulic press. To achieve the set goal, the following tasks must be solved: to determine the maximum permissible disassembly force of the axes, taking into account the strength of the load-bearing structure elements; to develop a concept of a mechanized hydraulic press, including the composition of the installation, the general technical description, the principle of operation, the kinematic scheme, and the tool. Studies have been carried out on the deformation modeling of mine support elements under load using the SOLIDWORKS Simulation calculation module to determine the maximum permissible disassembly force of the axes. It has been shown that the disassembly load of the shaft support axis with a force of more than 1000 kN leads to the loss of the structural strength reserve, which is unacceptable. An effective technology for dismantling the axes of a mechanized mine support has been proposed. A concept of an original specialized hydraulic press "Kit-100" for dismantling axes has been developed, which allows replacing the physically heavy and dangerous work of the operator with a lighter, mechanized process.Item Комп’ютерне моделювання процесу прямого пресування через різні профілі матричних лійок(ЦНТУ, 2020) Свяцький, В. В.; Скрипник, О. В.; Конончук, С. В.; Sviatskyi, V.; Skrypnyk, O.; Kononchuk, S.; Свяцкий, В. В.Виходячи з аналізу напруженого і деформованого стану стадії пресування, що встановилася, запропоновано використовувати профіль матричної лійки, виконаний по лінії ковзання, що розділяє пружну і пластичну зону. Результати теоретичних досліджень, комп’ютерного моделювання процесу прямого пресування за допомогою програмного комплексу Deform 2D/3D, експериментальних дослідів показали, що кращі умови пресування досягаються через матрицю із профілем, який виконаний по лінії ковзання. The stressed and deformed state of the metal and the dimensions of the center of deformation during pressing depend significantly on the design of the tool and, in particular, on the shape of the matrix funnel. However, there is still no single point of view on the influence of the geometry of the deformation center on the energy forces of the metal pressing process. Based on the analysis of the field of slip lines of the steady-state stage of pressing through a symmetric single-point matrix, it is proposed to use the profile of the matrix funnel made along the slip line separating the elastic and plastic zones. The following types of matrix funnel profiles were investigated using computer simulation of direct extrusion of lead samples with a drawing value 81 at a speed of 1 mm/s: cycloid concave; convex; the second convex, which is built on the logarithmic dependence; conical and concave, which is built along a sliding line that separates the elastic zones from the plastic in the pressing process. The results of theoretical studies, computer simulations of the direct pressing process using the Deform 2D/3D software package, and experimental experiments have shown that optimal energy-power conditions are achieved by pressing through a matrix that has a profile made along the slip line. The results of the experimental study of the kinetics of the flow of the discrete medium showed that the shape of the matrix funnel influences the size of the deformation center and the distribution of the resulting deformation in the molding. From the analysis of deformation of the granules, it is determined that the concave funnel, built along the slip line, is characterized by a curvature of the axisymmetric particles in the direction of deformation. These curvatures decrease as the granules move to the axis of symmetry of the matrix. It is noted that for a convex funnel, the length of the deformation center is greatest; for a conical metal flow is close to the radial in the direction of the truncated cones. На основе анализа поля линий скольжения установившейся стадии прессования через симметричную одноочковую матрицу предложено использовать профиль матричной воронки, выполненный по линии скольжения, разделяющий упругую и пластическую зону. Результаты теоретических исследований, компьютерного моделирования процесса прямого прессования с помощью программного комплекса Deform 2D/3D, экспериментальных опытов показали, что оптимальные энергосиловые условия достигаются при прессовании через матрицу, которая имеет профиль, выполненный по линии скольжения.Item Комбіновані методи обробки глибоких отворів(ЦНТУ, 2019) Свяцький, В. В.; Скрипник, О. В.; Сіса, О. Ф.; Конончук, С. В.; Свяцкий, В. В.; Скрипник, О. В.; Сиса, О. Ф.; Конончук, С. В.; Sviatskyi, V.; Skrypnyk, О.; Sisa, O.; Kononchuk, S.Наведено схеми розвантаження свердла, що основані на використанні комбінованої обробки „різання — пластична деформація” і підведенням мастильно-охолодного технічного засобу з надлишковим тиском. Способи вирішують задачі зниження складових технологічного навантаження і дозволяють розширити технологічні можливості процесу свердління по глибині обробки. Приведены схемы разгрузки сверла, основанные на использовании комбинированной обработки „резани – пластическая деформация” и подводом смазывающе-охлаждающего технического средства с избыточным давлением. Способы решают задачу снижения составляющих технологической нагрузки и позволяют расширить технологические возможности процесса сверления по глубине обработки. The drilling of deep openings is a labor-intensive technological process, especially when processing viscous materials. In the system "machine-fixture-tool-workpiece" with deep drilling in the most difficult conditions the tool – a drill. Closed processing volume, various functions, the implementation of which must provide the design of the tool, forced mode of cutting forced to work the drill body, its cutting and guiding elements with high stresses. Typically, the process of drilling deep openings is carried out on special or aggregate machines using a device containing a drill installed on a tubular stalk with ducts for chip removal and a lubricant receiving system for supplying a lubricating and cooling technical device under pressure. In the process of processing, the stem of the drill is under the influence of the axial component of the cutting force, which leads to its longitudinal bending and, consequently, to reduce the accuracy of the machining and stability of the tool. Optimization of the process of deep drilling is reduced, as a rule, to the removal of certain technical limitations on the stability, strength or stiffness of the drill. However, the possibility of increasing the stiffness of the tool due to the change in the shape of the cross section of the stem of the drill is currently sufficiently studied and practically exhausted. The above theoretical and experimental studies show that the control of the load of the tool stem along the axial component of the cutting force and the resistance forces is fundamentally possible with the use of processes of combined processing of openings. Developed methods of processing deep openings solve the problem of reducing the components of technological load and allow you to expand the technological capabilities of the drilling process at the depth of processing.Item Розмірна обробка електричною дугою бічної поверхні зносостійкого інструменту(ЦНТУ, 2018) Сіса, О. Ф.; Пукалов, В. В.; Юр’єв, В. В.; Сиса, О. Ф.; Юрьев, В. В.; Sisa, O.; Pukalov, V.; Yuryev, V.Виконано обґрунтування технологічної схеми формоутворення зовнішньої бічної поверхні пуансону, способом розмірної обробки електричною дугою з урахуванням особливостей фізичних механізмів їх утворення та гідродинамічних явищ в міжелектродному проміжку. Встановлені аналітичні зв’язки технологічних характеристик процесу розмірної обробки електричною дугою твердого сплаву ВК8 з режимами обробки і геометричними параметрами. Выполнено обоснование технологической схемы формообразования внешней боковой поверхности пуансона, способом размерной обработки электрической дугой с учетом особенностей физического механизма образования и гидродинамических явлений в межэлектродном промежутке. Установлены аналитические связи технологических характеристик процесса размерной обработки электрической дугой твердого сплава ВК8 с режимами обработки и геометрическими параметрами. The article is devoted to development of the technology and equipment for rough machining of hard-face puncheon's lateral surface with electrical arc as a highly efficient alternative to the conventional methods of rough machining. In order to extend the durability period of the sheet material blanking die, the strong wearproof materials should be used. The hard-face axial puncheons are used due to high strength, hardness and wearproofness. The puncheons are made of the cylindrical hard-face cores, with diameter ranging from 2...20 mm. Then they are grinded. The cores are made of hard alloys with wolfram carbide grain size less than 1 µm, and the 8...25% of cobalt binding content. The cores are produced by the hard-face powder pressing and further sintering in vacuum-compressor furnace. When sintering the cores shrink, followed with the contraction process. The core bending may reach up to 0.35 mm and more. Such curve cores are not used for grinding. Therefore, the problem is to find some optional technologies of treating the hard-face cores for the puncheons. It is suggested to remove the puncheon's lateral surface with electrical arc at the stage of the hard-face blank treatment. This allows removing large allowances of material along with the shortest treatment time. It is suggested to produce the puncheon lateral surface with roughness of Ra = 16…30 µm following rough machining. Thus, the large allowances of material are removed with the shortest treatment time. Here, the treatment cycle of the hard-face puncheon's lateral surface reduces by 1.4...1.8 times. The substantiation was made for the process flow diagram covering fabrication of the hard-face puncheon's lateral surface subject to specifics of the physical mechanism of formation and the hydrodynamic phenomena in the inter-electrode gap. The analytical links were determined between the technological specifications of the process featuring ВК8 alloy rough machining with electrical arc, the processing modes and geometrical parameters. The resulting models enable managing the capacity, specific capacity, specific consumption of electric power and the treated surface accuracy, along with forecasting and optimizing these parameters. The technical solution is offered enabling to expand the processing capacities of the hard-face puncheon's production.Item Можливість модернізації механічної обробки багатоступінчастих валів на токарних верстатах застарілої конструкції(КНТУ, 2013) Анастасенко, С. Н.; Григурко, І. О.; Капура, І. А.; Anastasenko, Sergey; Grigyrko, Ivan; Kapyra, ІgorПредставлена модернізація токарних верстатів застарілої конструкції з реконструкцією гідрокопіювальних супортів для обробки багатоступінчастих валів та улаштування для автоматизованого завантаження, закріплення і зняття заготовок. При конструкторській розробці на заводі можливо враховувати виробничі можливості ремонтних і інструментальних цехів, на котрі покладається задача переобладнання верстатів і ретельного розрахунку економічних показів, які визначають рентабельність реконструкції і степені автоматизації. В більшості випадків при автоматизації верстатів для роботи за замкнутим циклом виготовлення простих деталей можемо рекомендувати пневмомеханічні улаштування, комбінуючи механічний барабанний привід супорту з пневматичними затискними улаштуваннями. It is presented the putmoded turn bench with reengineering of hydro-copying carrage for multiplediameters part processing and computerized work pieces loading, fixture and relieving devices. At designer development at the plant it is possible to take into account production mo-zhlivosti of repair and instrumental workshops upon which the task of re-equipment of machine-tools and careful calculation of economic pokazkiv, yaki depends determine profitability of reconstruction and degrees of automation. In most cases during automation of machine-tools for work after the reserved cycle of vigotov-lennya of simple details can recommend the pneumomassage arranging, combining a mechanical drum occasion support from.